Engineering topics

Paetel, Stefan

Publications and source records attributed to Paetel, Stefan.

7 records

DOE OSTI2024

Improved VOC in RbF-Treated Cu(In,Ga)Se2 Solar Cells via Passivation of Recombination Centers

Cu(In,Ga)Se 2 (CIGS) solar cells have benefited in recent years from the addition of heavy alkali elements, such as Rb, which increase the solar cell open-circuit voltage ( V OC ). To investigate the source of this improvement, here, we compare samples with and without Rb to perform a quantitative comparison of electronic defects and minority carrier lifetime. Deep-level transient and optical spectroscopy measurements were performed on two sets of rubidium fluoride (RbF)-treated and untreated CIGS, and three distinct traps were identified regardless of RbF treatment. The RbF treatment was found to reduce the concentration of the H2 trap, which was previously found to act as a recombination center and is located preferentially at CIGS grain boundaries. Time-resolved photoluminescence measurements showed an increase in effective lifetime after RbF and nearly all lifetime improvement resulted from reductions in bulk recombination. The observed V OC improvement is well correlated with increased minority carrier lifetime and acceptor concentration, which led to increases and decreases in electron and hole quasi-Fermi levels, respectively.

Cu(In Ga)Se2 (CIGS)↗

DOE OSTI2023

Defects in RbF - Treated Cu(InxGal-x)Se2 Solar Cells and Their Impact on Voc

Cu(In,Ga)Se2 solar cell efficiency is limited by VOC due in large part to bulk defects limiting lifetime, but alkali treatments such as RbF recover some of the VOC loss. In this work, defects in RbF-treated and untreated CIGS were quantitatively characterized using DLTS and DLOS, and three main defects were identified in each sample. The RbF-PDT resulted in a large decrease in the mid-gap trap concentration, which was accompanied by a large improvement in minority carrier lifetime. This lifetime improvement combined with a change in doping accounted for a significant portion of the VOC improvement in the RbF CIGS.

charge carrier lifetime↗

DOE OSTI2023

Photovoltaic device innovation for a solar future

Photovoltaics (PV), also known as solar cells, are now found everywhere - in utility plants; on roofs of homes and commercial buildings; on platforms at sea; in agricultural fields; on vehicles, buildings, drones, and backpacks; and, in their longest running application, providing power in space. Continuous device innovation has led to increased efficiency and improved reliability for multiple PV technologies. Confronted with an urgent need to deploy PV at multiterawatt (TW) scale over the next two decades to mitigate greenhouse gas emissions, PV device innovation takes on new urgency and impact. This perspective reviews recent progress in device design and performance for PV technologies that are currently in commercial production at greater than 1 GW/year or enabling significant space-based power generation - Si, CdTe, CIGS, and multijunction III-V - and looks ahead to the next 5 years. In conclusion, we also identify device-related topics requiring cross-cutting research and innovation.

14 SOLAR ENERGY↗

DOE OSTI2023

Nonradiative Recombination Dominates Voltage Losses in Cu(In,Ga)Se 2 Solar Cells Fabricated using Different Methods

Voltage losses reduce the photovoltaic conversion efficiency of thin‐film solar cells and are a primary efficiency limitation in Cu(In,Ga)Se 2 . Herein, voltage loss analysis of Cu(In,Ga)Se 2 solar cells fabricated at three institutions with variation in process, bandgap, absorber structure, postdeposition treatment (PDT), and efficiency is presented. Nonradiative voltage losses due to Shockley–Read–Hall charge carrier recombination dominate and constitute >75% of the total compared to <25% from radiative voltage losses. The radiative voltage loss results from nonideal absorption and carriers in band tails that stem from local composition‐driven potential fluctuations. It is shown that significant bulk lifetime improvements are achieved for all alkali PDT processed absorbers, chiefly associated with reductions in nonradiative recombination. Primary voltage loss contributions (radiative and nonradiative) change little across fabrication processes, but variation in submechanisms (bulk lifetime, net acceptor concentration, and interface recombination) differentiate nonradiative loss pathways in this series of solar cells.

14 SOLAR ENERGY↗

DOE OSTI2022

Bandgap Dependence of Near-Conduction Band State in (AgyCu1-y)(InXGa1-x)Se2 Solar Cells

(Ag, CU) (In,Ga)Se2 -based solar cells have achieved high collection efficiencies, but defects still limit efficiencies well below the theoretical limit. The near-conduction band defect, typically observed at EV+0.98 eV, has been ubiquitous across (Ag,Cu)(In,Ga)Se2 samples from multiple vendors. The current work explores a wider range of composition and demonstrates the trap energy varies relative to the valence band but is approximately constant relative to the conduction band (~Ec-0.13 eV). There is also no definitive dependence of the trap concentration on composition.

ACIGS↗

DOE OSTI2022

Evaluating Recombination Mechanisms in RbF Treated Cu(In${}_\mathrm{x}$Ga$_\mathrm{1-x}$)Se$_{2}$ Solar Cells

Rubidium fluoride (RbF) postdeposition treatment (PDT) has been shown to improve the performance of Cu(In x Ga 1-x )Se 2 (CIGS) photovoltaic devices. Here, in this study, temperature-dependent current voltage (JVT) and time-resolved photoluminescence (TRPL) experiments were combined with modeling using the solar cell capacitance simulator (SCAPS) computer code to investigate the effect of the RbF PDT. Two devices, one as-deposited and one with RbF PDT, were deposited by a three stage coevaporation process. JVT measurements suggest the dominant recombination mechanism may be tunneling-enhanced recombination via bandtail states, but that defect states in the bandgap can also be important. RbF PDT is shown to decrease the characteristic energy of the bandtails. TRPL data show an increase in the minority carrier lifetime after RbF PDT, leading to an improved open-circuit voltage. SCAPS modeling indicates that the dominant recombination mechanism is dependent on the specific defect makeup of a device, suggesting that small changes in processing conditions can impact device behavior. This explains the observation that, for some devices, defect states in the gap dominate while others, as is the case here, appear to be dominated by bandtails.

14 SOLAR ENERGY↗

DOE OSTI2020

Behavior of Na and RbF-Treated CdS/Cu(In,Ga)Se 2 Solar Cells with Stress Testing under Heat, Light, and Junction Bias

In this work, the effects of Na and RbF alkali treatment on the metastability behavior of CdS/Cu(In,Ga)Se 2 solar cells are investigated with stress factors of heat, junction bias, and illumination. Four device types with and without Na or RbF treatments are subjected to heat- and light-soaking under open- and short-circuit (OC, SC) junction bias. Low-Na devices show a higher bandgap due to increased minimum Ga content, higher recombination current, and lower open-circuit voltage (V OC ). Devices with RbF post-deposition treatment (PDT) show an improvement in net doping density ≈10 16 cm –3 , V OC , and efficiency. Heat- and light-soaking under OC junction bias provokes an increase in net carrier concentration and V OC irrespective of the alkali treatments. After SC stress, a decrease in V OC and net carrier concentration is observed, which can be stabilized by RbF-PDT. An increase in Na and oxygen concentration in CIGS is observed for baseline and low-Na devices, respectively, after OC stress. The oxygen concentration in CdS decreases after heat- and light-soaking for devices without RbF-PDT, whereas it remains unchanged for devices with RbF-PDT. The atomic concentration profiles in CIGS significantly stabilize as a function of stress with the addition of RbF-PDT.

14 SOLAR ENERGY↗