Search NASA⌕ Search

Engineering topics

Paik, Haemin

Publications and source records attributed to Paik, Haemin.

Uncovering the Network Modifier for Highly Disordered Amorphous Li‐Garnet Glass‐Ceramics

Abstract Highly disordered amorphous Li 7 La 3 Zr 2 O 12 (aLLZO) is a promising class of electrolyte separators and protective layers for hybrid or all‐solid‐state batteries due to its grain‐boundary‐free nature and wide electrochemical stability window. Unlike low‐entropy ionic glasses such as Li x PO y N z (LiPON), these medium‐entropy non‐Zachariasen aLLZO phases offer a higher number of stable structure arrangements over a wide range of tunable synthesis temperatures, providing the potential to tune the LBU‐Li + transport relation. It is revealed that lanthanum is the active “network modifier” for this new class of highly disordered Li + conductors, whereas zirconium and lithium serve as “network formers”. Specifically, within the solubility limit of La in aLLZO, increasing the La concentration can result in longer bond distances between the first nearest neighbors of Zr─O and La─O within the same local building unit (LBU) and the second nearest neighbors of Zr─La across two adjacent network‐former and network‐modifier LBUs, suggesting a more disordered medium‐ and long‐range order structure in LLZO. These findings open new avenues for future designs of amorphous Li + electrolytes and the selection of network‐modifier dopants. Moreover, the wide yet relatively low synthesis temperatures of these glass‐ceramics make them attractive candidates for low‐cost and more sustainable hybrid‐ or all‐solid‐state batteries for energy storage.

36 MATERIALS SCIENCE↗

Highly disordered amorphous Li-battery electrolytes

"Medium-entropy" highly disordered amorphous Li garnets, with ≥4 unique local bonding units (LBUs), hold promise for use as solid-state electrolytes in hybrid or all-solid-state batteries owing to their grain-boundary-free nature and low-temperature synthesis requirement. Through this work, we resolved the local structure of amorphous Li garnet and understood their implication for Li dynamics. These medium-entropy amorphous structures possess unique characteristics with edge- and face-sharing LBUs, not conforming to the classic Zachariasen glass formation rules, and can be synthesized in a wide but processing-friendly temperature range (<680°C). Within these amorphous structures, Li and Zr are identified as the network formers and La as network modifier, with maxima in Li dynamics observed for smaller Li-O and Zr-O coordination; this structure understanding serves as a baseline for identifying additional network formers to further modulate Li transport. In conclusion, our insight provides fundamental guidelines for the structure and phase design for amorphous Li garnets and paves the way for their integration in next-generation batteries.

25 ENERGY STORAGE↗

Hydrogen oxidation kinetics on platinum-palladium bimetallic thin films for solid acid fuel cells

Solid acid fuel cells (SAFCs) based on the proton-conductive electrolyte CsH 2 PO 4 have shown promising power densities at an intermediate operating temperature of ~250 °C. However, Pt loadings in SAFCs remain higher than desirable, and the electrocatalysis mechanisms in these devices are still unknown. Here, hydrogen oxidation kinetics on Pt and Pt-Pd bimetallic thin film electrodes on CsH 2 PO 4 have been evaluated to establish the potential for a beneficial role of Pd in SAFC anodes. Symmetric cells fabricated by depositing a metal film on both sides of electrolyte discs are characterized for studying hydrogen electro-oxidation across the gas|metal|CsH 2 PO 4 structure. It was found that Pd reacts with CsH 2 PO 4 , forming palladium phosphide at the metal-electrolyte interface. Accordingly, the activity of Pd was examined in a bilayer geometry of Pd|Pt|CsH 2 PO 4 |Pt|Pd. The bilayer Pt|Pd films showed much higher activity for hydrogen electro-oxidation than films of Pt alone, as measured by AC impedance spectroscopy. Ex situ low energy ion scattering and scanning transmission electron microscopy revealed that Pd diffused into the Pt layer under operating conditions. The dramatic impact of Pd along with its presence throughout the film suggests that it catalyzes reactions at both the metal-gas and metal-electrolyte interfaces, as well as increasing hydrogen diffusion rates through the films.

36 MATERIALS SCIENCE↗

Atomic layer deposition of Pt@CsH 2 PO 4 for the cathodes of solid acid fuel cells

Atomic layer deposition (ALD) has been used to apply continuous Pt films on powders of the solid acid CsH 2 PO 4 (CDP), in turn, used in the preparation of cathodes in solid acid fuel cells (SAFCs). The film deposition was carried out at 150 °C using trimethyl(methylcyclopentadienyl)platinum (MeCpPtMe 3 ) as the Pt source and ozone as the reactant for ligand removal. Chemical analysis showed a Pt growth rate of 0.09 ± 0.01 wt%/cycle subsequent to an initial nucleation delay of 84 ± 20 cycles. Electron microscopy revealed the contiguous nature of the films prepared using 200 or more cycles. The cathode overpotential (0.48 ± 0.02 V at a current density of 200 mA/cm 2 ) was independent of Pt deposition amount beyond the minimum required to achieve these continuous films. The cell electrochemical characteristics were moreover extremely stable with time, with the cathode overpotentials increasing by no more than 10 mV over a 100 h period of measurement. So, ALD holds promise as an effective tool in the preparation of SAFC cathodes with high activity and excellent stability.

25 ENERGY STORAGE↗

Effect of Ag nanoparticle concentration on the electrical and ferroelectric properties of Ag/P(VDF-TrFE) composite films

Here, we investigated the effect of the Ag nanoparticles on the ferroelectric and piezoelectric properties of Ag/poly(vinylidenefluoride-trifluoroethylene) (P(VDF-TrFE)) composite films. We found that the remanent polarization and direct piezoelectric coefficient increased up to 12.14 μC/cm 2 and 20.23 pC/N when the Ag concentration increased up to 0.005 volume percent (v%) and decreased down to 9.38 μC/cm 2 and 13.45 pC/N when it increased up to 0.01 v%. Further increase in Ag concentration resulted in precipitation of Ag phase and significant leakage current that hindered any meaningful measurement of the ferroelectric and piezoelectric properties. 46% increase of the remanent polarization value and 27% increase of the direct piezoelectric coefficient were observed in the film with the 0.005 v% of the Ag nanoparticles added without significant changes to the crystalline structure confirmed by both X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) experiments. The enhancements of both the ferroelectric and piezoelectric properties are attributed to the increase in the effective electric field induced by the reduction in the effective volume of P(VDF-TrFE) that results in more aligned dipoles.

36 MATERIALS SCIENCE↗

Vertically aligned P(VDF-TrFE) core-shell structures on flexible pillar arrays

PVDF and P(VDF-TrFE) nano- and micro- structures are widely used due to their potential applications in several fields, including sensors, actuators, vital sign transducers, and energy harvesters. In this study, we developed vertically aligned P(VDF-TrFE) core-shell structures using high modulus polyurethane acrylate (PUA) pillars as the support structure to maintain the structural integrity. In addition, we were able to improve the piezoelectric effect by 1.85 times from 40 ± 2 to 74 ± 2 pm/V when compared to the thin film counterpart, which contributes to the more efficient current generation under a given stress, by making an effective use of the P(VDF-TrFE) thin top layer as well as the side walls. We attribute the enhancement of piezoelectric effects to the contributions from the shell component and the strain confinement effect, which was supported by our modeling results. We envision that these organic-based P(VDF-TrFE) core-shell structures will be used widely as 3D sensors and power generators because they are optimized for current generations by utilizing all surface areas, including the side walls of core-shell structures.

30 DIRECT ENERGY CONVERSION↗