Search NASA⌕ Search

Engineering topics

Pak, A.

Publications and source records attributed to Pak, A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser-driven flash x-ray radiography of a shocked metallic foil

Characterizing hydrodynamic instability evolution in millimeter-scale, high-Z foils is crucial for understanding complex phenomena in high-energy-density physics. Here, we demonstrate a proof-of-concept, laser-driven flash x-ray radiography platform tailored for two-dimensional linear density mapping in shocked high-Z foils. Using chromium (Cr) foils with internal shockwaves (∼100 μm width), our platform achieves a spatial resolution of 59.8 ± 1.4 μm by employing a broadband x-ray source extending into the hundreds of keV range. The setup combines a compound parabolic concentrator cone with a tantalum wire target, a magnetic field to deflect residual transmitted electrons, and a copper casing to shield the sides and rear of the image plate pack. By varying the delay of the short-pulse beam driving the flash x-ray source, we resolve shockwave dynamics, specifically the velocity, position, width, and density profile, within the Cr foil. Reported experimental results are consistent with the corresponding hydrodynamics and radiation transport simulations, which accurately reproduce the measured electron and x-ray source terms. These developments enable the conversion of shockwave radiographs into two-dimensional density maps, enhancing interpretability for hydrodynamic instability evolution applications and validating the simulation approach.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermonuclear performance variability near ignition at the National Ignition Facility

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.

Divol, L. (ORCID:0000000269699898)↗
DOE OSTI2024

Diagnosing inertial confinement fusion ignition

Abstract Fusion ignition by inertial confinement requires compression and heating of the fusion fuel to temperatures in excess of 5 keV and densities exceeding hundreds of g/cc. In August 2021, this scientific milestone was surpassed at the National Ignition Facility (NIF), when the Lawson criterion for ignition was exceeded generating 1.37MJ of fusion energy (Abu-Shawareb et al 2022 Phys. Rev. Lett. 129 075001), and then in December 2022 target gain >1 was realized with the production of 3.1MJ of fusion energy from a target driven by 2.0MJ of laser energy (Abu-Shawareb et al 2024 Phys. Rev. Lett. 132 065102). At the NIF, inertial confinement fusion research primarily uses a laser indirect drive in which the fusion capsule is surrounded by a high-Z enclosure (‘hohlraum’) used to convert the directed laser energy into a symmetric x-ray drive on the capsule. Precise measurements of the plasma conditions, x-rays, γ -rays and neutrons produced are key to understanding the pathway to higher performance. This paper discusses the diagnostics and measurement techniques developed to understand these experiments, focusing on three main topics: (1) key diagnostic developments for achieving igniting plasmas, (2) novel signatures related to thermonuclear burn and (3) advances to diagnostic capabilities in the igniting regime with a perspective toward developments for intertial fusion energy.

Moore, A. S. (ORCID:0000000221258882)↗
DOE OSTI2024

Design and analysis of dudded fuel experiments at the National Ignition Facility

Recent experiments conducted at the National Ignition Facility (NIF) within the past 2 years have achieved the burning plasma state and exceeded the Lawson criterion for the first time in the laboratory. Here, we report on a set of experiments where the deuterium and tritium (DT) ice layers were replaced with dudded tritium, hydrogen, and deuterium (THD) fuel mixtures to remove the influence of alpha-heating on hot spot dynamics. The hot spot compression and yield in the absence of alpha particle self-heating were measured to assess the proximity of NIF implosions toward the ignition cliff. We find that the “burn-off” Lawson parameters χnoα inferred from the THD experiments are in good agreement with the inferences from postshot simulations of the DT-layered implosions. The THD for burning plasma shot N210307 yielded χnoα≈0.88±0.03 while the THD for ignition shot N210808 yielded χnoα≈1.04±0.04. These results also provide important context for the observed variability in the repeat attempts of ignition shot N210808 since implosions on the ignition cliff are expected to exhibit very large variations in the fusion yield from small changes in the initial conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Ultrabroad-band x-ray source using a picosecond, laser-driven plasma accelerator

An ultrabroad-band x-ray source, with photon energies from 10 keV to >1 MeV, based on a picosecond laser-driven plasma accelerator, is characterized and used to radiograph high-energy-density-science relevant targets. The measured yield of 10 12 photons/shot is reaching the necessary photon yields to radiograph, in a single shot, high areal density objects and matter under extreme conditions. By focusing a short laser pulse (120 J, 1 ps) into a gas jet, a < 100 mrad electron beam with energies up to 350 MeV and up to 70 nC of charge was produced by a combination of laser self-modulation instability and direct laser acceleration. A foil placed at the exit of the gas jet is used to convert part of the electron beam energy into x rays through inverse bremsstrahlung and/or inverse Compton scattering, generating a bright, broad-band, high-photon-energy beam. This beam is used to radiograph a gold half hohlraum with a high-density sphere inside with relevant characteristics for high-energy-density science and inertial confinement fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

The impact of low-mode symmetry on inertial fusion energy output in the burning plasma state

Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Observations and properties of the first laboratory fusion experiment to exceed a target gain of unity

An indirect-drive inertial fusion experiment on the National Ignition Facility was driven using 2.05 MJ of laser light at a wavelength of 351 nm and produced 3.1±0.16 MJ of total fusion yield, producing a target gain G=1.5±0.1 exceeding unity for the first time in a laboratory experiment [Phys. Rev. E 109, 025204 (2024)]. Herein we describe the experimental evidence for the increased drive on the capsule using additional laser energy and control over known degradation mechanisms, which are critical to achieving high performance. Further, improved fuel compression relative to previous megajoule-yield experiments is observed. Novel signatures of the ignition and burn propagation to high yield can now be studied in the laboratory for the first time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Diagnosing the origin and impact of low-mode asymmetries in ignition experiments at the National Ignition Facility

Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. Here we show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Reduced mixing in inertial confinement fusion with early-time interface acceleration

In inertial confinement fusion (ICF) implosions, the interface between the cryogenic DT fuel and the ablator is unstable to shock acceleration (the Richtmyer-Meshkov instability, RM) and constant acceleration (Rayleigh-Taylor instability, RT). Instability growth at this interface can reduce the final compression, limiting fusion burnup. If the constant acceleration is in the direction of the lighter material (negative Atwood number), the RT instability produces oscillatory motion that can stabilize against RM growth. Theory and simulations suggest this scenario occurred at early times in some ICF experiments on the National Ignition Facility, possibly explaining their favorable performance compared to one-dimensional simulations. In conclusion, this characteristic is being included in newer, lower adiabat designs, seeking to improve compression while minimizing ablator mixing into the fuel.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Measuring and simulating ice–ablator mix in inertial confinement fusion

Fuel–ablator mix has been established as a major performance degrading effect in the burning plasma regime of recent inertial confinement fusion (ICF) experiments. As such, the study of fuel–ablator mix with experiments and simulations can provide valuable insight for our understanding of these experiments and establish a path for even higher yields and increased robustness. Here we present a novel high-yield experimental ICF design that is motivated by recent experiments measuring ice–ablator mix with a CH ablator instead of a high-density carbon (HDC) ablator. Here we review these experiments in more detail and describe the modeling assumptions and parameters used to obtain agreement with the data from implosion and burn simulations with mix. Using this mix model calibrated a posteriori to the experimental data, we design an implosion that uses a CH ablator that is predicted to achieve better performance than a recent experiment that achieved net target gain of 1.5 in HDC. Because hydrodynamic instabilities are greatly reduced with this new design, we also expect a high reproducibility at the same implosion adiabat as current record yield experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Enhanced electron acceleration by high-intensity lasers in extended (confined) preplasma in cone targets

Here we report on experimental results from a high-intensity laser interaction with cone targets that increase the number (×3) and temperature (×3) of the measured hot electrons over a traditional planar target. This increase is caused by a substantial increase in the plasma density within the cone target geometry, which was induced by 17 ± 9 mJ prepulse that arrived 1.5 ns prior to the main high intensity (>10 19 W/cm 2 ). Three-dimensional hydrodynamic simulations are conducted using hydra which show that the cone targets create substantially longer and denser plasma than planar targets due to the geometric confinement of the expanding plasma. The density within the cone is a several hundred-micron plasma “shelf” with a density of approximately 10 20 n e /cc. The HYDRA simulated plasma densities are used as the initial conditions for two-dimensional particle-in-cell simulations using EPOCH. These simulations show that the main acceleration mechanism is direct-laser-acceleration, with close agreement between experimentally measured and simulated electron temperatures. Further analysis is conducted to investigate the acceleration of the electrons within the long plasma generated within a compound parabolic concentrator by the prepulse.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Alpha heating of indirect-drive layered implosions on the National Ignition Facility

We report in order to understand how close current layered implosions in indirect-drive inertial confinement fusion are to ignition, it is necessary to measure the level of alpha heating present. To this end, pairs of experiments were performed that consisted of a low-yield tritium–hydrogen–deuterium (THD) layered implosion and a high-yield deuterium–tritium (DT) layered implosion to validate experimentally current simulation-based methods of determining yield amplification. The THD capsules were designed to reduce simultaneously DT neutron yield (alpha heating) and maintain hydrodynamic similarity with the higher yield DT capsules. The ratio of the yields measured in these experiments then allowed the alpha heating level of the DT layered implosions to be determined. The level of alpha heating inferred is consistent with fits to simulations expressed in terms of experimentally measurable quantities and enables us to infer the level of alpha heating in recent high-performing implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Recovery of release cloud from laser shock-loaded graphite and hydrocarbon targets: in search of diamonds

Abstract This work presents first insights into the dynamics of free-surface release clouds from dynamically compressed polystyrene and pyrolytic graphite at pressures up to 200 GPa, where they transform into diamond or lonsdaleite, respectively. These ejecta clouds are released into either vacuum or various types of catcher systems, and are monitored with high-speed recordings (frame rates up to 10 MHz). Molecular dynamics simulations are used to give insights to the rate of diamond preservation throughout the free expansion and the catcher impact process, highlighting the challenges of diamond retrieval. Raman spectroscopy data show graphitic signatures on a catcher plate confirming that the shock-compressed PS is transformed. First electron microscopy analyses of solid catcher plates yield an outstanding number of different spherical-like objects in the size range between ten(s) up to hundreds of nanometres, which are one type of two potential diamond candidates identified. The origin of some objects can unambiguously be assigned, while the history of others remains speculative.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Yield degradation mechanisms for two-shock capsules evaluated through simulations

An investigation of twenty two-shock campaign indirectly driven capsules on the National Ignition Facility was conducted using the xRAGE computer code. The two-shock platform was developed to look at the sensitivity of fuel–ablator mix with shock timing, asymmetry, surface roughness, and convergence on roughly ignition size scale capsules. This platform used CH/CD (plastic/deuterated plastic) shell capsules that were about 685-μm outer radius and filled with D2 or hydrogen-tritium (HT) gas. The experimental radius and velocity vs time, neutron yield, burn averaged ion temperature (Tion), burn width, and self-emission image size were compared to one-dimensional (1D) and two-dimensional (2D) simulations. Our 2D simulations suggest that the mixing of glass from the fill tube was the dominant source of impurity in the gas region of the capsule during burn, along with fuel–ablator mix. The mass of glass mixed in is about 5–10 ng. Our 2D simulations capture most of the yield trends from different degradation mechanisms, and they match the observed burn width and Tion measurements. Our 2D models match all the available data to within 2.5 times the normalized experimental error for 19 of 20 capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗