Search NASA⌕ Search

Engineering topics

Pak, A.

Publications and source records attributed to Pak, A..

At least 55 records · Page 3

Laser-driven collisionless shock acceleration of ions from near-critical plasmas

Here, this paper overviews experimental and numerical results on acceleration of narrow energy spread ion beams by an electrostatic collisionless shockwave driven by 1 μm (Omega EP) and 10 μm (UCLA Neptune Laboratory) lasers in near critical density CH and He plasmas, respectively. Shock waves in CH targets produced high-energy ~50 MeV protons (ΔE/E of ≤30%) and 314 MeV C 6+ ions (ΔE/E of ≤10%). Observation of acceleration of both protons and carbon ions to similar velocities is consistent with reflection of particles off the moving potential of a shock front. For shocks driven by CO 2 laser in a gas jet, ~30 MeV peak in He ion spectrum was detected. Particle-in-cell simulations indicate that regardless of the target further control over its density profile is needed for optimization of accelerated ion beams in part of energy spread, yield and maximum kinetic energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Symmetric fielding of the largest diamond capsule implosions on the NIF

We present results for the largest diamond capsule implosions driven symmetrically on the National Ignition Facility (NIF) (inner radius of ~1050 μm) without the use of cross beam transfer in cylindrical Hohlraums. We show that the methodology of designing Hohlraum parameters in a semi-empirical way using an extensive database resulted in a round implosion. In addition, we show that the radiation flux symmetry is well controlled during the foot of the pulse and that swings in P2 symmetry between the inflight dense shell and hot spot are within ±4 μm and that swings around peak compression are also within the symmetry specification of ±4 μm. We observed a stronger dependence of symmetry on the capsule scale than previously observed and also observed enhanced inner beam propagation for experiments using a gas fill density of 0.3 mg/cm 3 and 1000 μm inner radius capsules. We have observed sufficient symmetry and mass remaining at near full NIF power and energy, up to 480 TW and 1.9 MJ, with little laser–plasma interactions (low laser backscattered light) and predict that this design could support extended NIF energy of up to 2.1 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent and planned hydrodynamic instability experiments on indirect-drive implosions on the National Ignition Facility

At National Ignition Facility (NIF), yield amplification due to alpha particle heating approached ~3 in the highest performing inertial confinement fusion (ICF) implosions, while yield amplification of ~15-30 is needed for ignition. Hydrodynamic instabilities are a major factor in degradation of implosions while understanding and mitigation of the instabilities are critical to achieving ignition. This article describes recent and planned hydrodynamic instability experiments with several focused platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock generation at OMEGA laser have indicated initial seeds for the instabilities in three ablators - plastic (CH), beryllium, and high-density carbon (HDC). Hydrodynamic Growth Radiography (HGR) platform was used to measure instability growth at the ablation front in the acceleration phase of implosions. This platform used pre-imposed 2-D perturbations for growth factor measurements at different perturbation wavelengths and was also used to measure growth of “native roughness” modulations, fill tubes, and capsule support membranes or “tents”. Also, in the acceleration phase several new experimental platforms have been or are being developed to measure instability growth at the ablator-ice interface. In the deceleration phase of implosions, “self-emission” and “self-backlighting” platforms were developed to measure perturbations near peak compression. This article reviews recent progress and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hotspot conditions achieved in inertial confinement fusion experiments on the National Ignition Facility

We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mixing in ICF implosions on the National Ignition Facility caused by the fill-tube

The micrometer-scale tube that fills capsules with thermonuclear fuel in inertial confinement fusion experiments at the National Ignition Facility is also one of the implosion's main degradation sources. It seeds a perturbation that injects the ablator material into the center, radiating away some of the hot-spot energy. This paper discusses how the perturbation arises in experiments using high-density carbon ablators and how the ablator mix interacts once it enters the hot-spot. Both modeling and experiments show an in-flight areal-density perturbation and localized x-ray emission at stagnation from the fill-tube. Simulations suggest that the fill-tube is degrading an otherwise 1D implosion by ~2×, but when other degradation sources are present, the yield reduction is closer to 20%. Characteristics of the fill-tube assembly, such as the through-hole size and the glue mass, alter the dynamics and magnitude of the degradation. Overall, these aspects point the way toward improvements in the design, some of which (smaller diameter fill-tube) have already shown improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of diamond nucleation rates from hydrocarbons at conditions comparable to the interiors of icy giant planets

We present measurements of the nucleation rate into a diamond lattice in dynamically compressed polystyrene obtained in a pump-probe experiment using a high-energy laser system and in situ femtosecond x-ray diffraction. Different temperature-pressure conditions that occur in planetary interiors were probed. For a single shock reaching 70 GPa and 3000 K no diamond formation was observed, while with a double shock driving polystyrene to pressures around 150 GPa and temperatures around 5000 K nucleation rates between 10 29 and 10 34 m –3 s –1 were recorded. These nucleation rates do not agree with predictions of the state-of-the-art theoretical models for carbon-hydrogen mixtures by many orders of magnitude. Our data suggest that there is significant diamond formation to be expected inside icy giant planets like Neptune and Uranus.

43 PARTICLE ACCELERATORS↗

Maintaining low-mode symmetry control with extended pulse shapes for lower-adiabat Bigfoot implosions on the National Ignition Facility

The Bigfoot approach to indirect-drive inertial confinement fusion has been developed as a compromise trading high convergence and areal densities for high implosion velocities, large adiabats, and hydrodynamic stability. Shape control and predictability are maintained by using relatively short laser pulses and merging the shocks within the deuterium-tritium-ice layer. These design choices ultimately limit the theoretically achievable performance, and one strategy to increase the 1D performance is to reduce the shell adiabat by extending the pulse shape. However, this can result in the loss of low-mode symmetry control, as the hohlraum “bubble,” the high-Z material launched by the outer-cone beams during the early part of the laser pulse, has more time to expand and will eventually intercept inner-cone beams preventing them from reaching the hohlraum waist, thus losing an equatorial capsule drive. Experiments were performed to study the shape control and predictability with extended pulse shapes in Bigfoot implosions, reducing the adiabat from nominally α~4 to α~3 and otherwise very similar experimental parameters. Lastly, the implosion shape was measured both in-flight and at stagnation, with near-round implosions and low levels of P 2 asymmetry throughout, indicating a maintained symmetry control with extended pulse shapes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reply to: Reconsidering X-ray plasmons

In this response we show a spectral and X-ray intensity analysis that unequivocally proves a spectrally resolved plasmon reported in ref. 1. The analysis takes the f-sum rules into account, is consistent with the independently and simultaneously measured wavenumber-resolved X-ray scattering signal and compares well with advanced elastic feature modelling, including density functional theory for molecular dynamics (DFTMD) as well as pseudoatom molecular dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Review of hydrodynamic instability experiments in inertially confined fusion implosions on National Ignition Facility

Hydrodynamic instabilities are a major factor in degradation of inertial confinement fusion (ICF) implosions. In the highest performing implosions on National Ignition Facility, yield amplification (YA) due to alpha particle heating approached ~3, while YA of ~15–30 is needed for ignition. Understanding and mitigation of the instabilities are critical to achieving ignition. This article reviews several experimental platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock propagation at OMEGA laser has provided results on initial seeds for the instabilities in three ablators—plastic (CH), beryllium, and high-density carbon. Additionally, at the ablation front, instability growth of pre-imposed modulations was measured in the linear regime using the hydrodynamic growth radiography platform. This platform was extended for modulation growth of 'native roughness' modulations and engineering features (fill tubes and capsule support membranes or 'tents'). Several new experimental platforms have or are being developed to measure instability growth at the ablator–ice interface. In the deceleration phase of implosions, complementary 'self-emission' and 'self-backlighting' platforms were developed to measure low-mode asymmetries and high-mode perturbations near peak compression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress of indirect drive inertial confinement fusion in the United States

Abstract Indirect drive converts high power laser light into x-rays using small high- Z cavities called hohlraums. X-rays generated at the hohlraum walls drive a capsule filled with deuterium–tritium (DT) fuel to fusion conditions. Recent experiments have produced fusion yields exceeding 50 kJ where alpha heating provides ~3× increase in yield over PdV work. Closing the gaps toward ignition is challenging, requiring optimization of the target/implosions and the laser to extract maximum energy. The US program has a three-pronged approach to maximize target performance, each closing some portion of the gap. The first item is optimizing the hohlraum to couple more energy to the capsule while maintaining symmetry control. Novel hohlraum designs are being pursued that enable a larger capsule to be driven symmetrically to both reduce 3D effects and increase energy coupled to the capsule. The second issue being addressed is capsule stability. Seeding of instabilities by the hardware used to mount the capsule and fill it with DT fuel remains a concern. Work reducing the impact of the DT fill tubes and novel capsule mounts is being pursed to reduce the effect of mix on the capsule implosions. There is also growing evidence native capsule seeds such as a micro-structure may be playing a role on limiting capsule performance and dedicated experiments are being developed to better understand the phenomenon. The last area of emphasis is the laser. As technology progresses and understanding of laser damage/mitigation advances, increasing the laser energy seems possible. This would increase the amount of energy available to couple to the capsule, and allow larger capsules, potentially increasing the hot spot pressure and confinement time. The combination of each of these focus areas has the potential to produce conditions to initiate thermo-nuclear ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Approaching a burning plasma on the NIF

The locus of National Ignition Facility (NIF) inertial confinement fusion (ICF) implosion data, in hot-spot burn-average areal density (ρR) and Brysk temperature (T) space, is shown here and illustrates that several implosions are nearing a burning plasma state, where α-heating is the dominant source of plasma heating. A formula for diagnosing a burning plasma using measured/inferred data from ICF implosion experiments is given with the underlying derivation. Plotting ICF implosion performance against inferred hot-spot energy illustrates the key need to maximize the delivery of energy to an implosion hot-spot. A very compact analytical equation for α-heating is given, which shows that fundamentally, α-heating provides a discrete “boost” to p V γ of an implosion hot-spot. It is then shown numerically that the analytical expression for the amplification of p V γ is simply related to yield amplification and to other more famous metrics used for inferring yield amplification in experiments. Interestingly, the argument of the p V γ boost equation appears to provide a fundamental ignition condition that implicitly includes the effects of asymmetry, and it also exposes the origin of why there is uncertainty in defining single ignition criteria. The resulting analysis of NIF implosion data indicates that an increase in burn-average hot-spot temperature will be needed in order to ignite, and the strategy being pursued to achieve this goal is outlined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First demonstration of ARC-accelerated proton beams at the National Ignition Facility

New short-pulse kilojoule, Petawatt-class lasers, which have recently come online and are coupled to large-scale, many-beam long-pulse facilities, undoubtedly serve as very exciting tools to capture transformational science opportunities in high energy density physics. These short-pulse lasers also happen to reside in a unique laser regime: very high-energy (kilojoule), relatively long (multi-picosecond) pulse-lengths, and large (10s of micron) focal spots, where their use in driving energetic particle beams is largely unexplored. Proton acceleration via Target Normal Sheath Acceleration (TNSA) using the Advanced Radiographic Capability (ARC) short-pulse laser at the National Ignition Facility in the Lawrence Livermore National Laboratory is demonstrated for the first time, and protons of up to 18 MeV are measured using laser irradiation of >1 ps pulse-lengths and quasi-relativistic (10 18 W/cm 2 ) intensities. This is indicative of a super-ponderomotive electron acceleration mechanism that sustains acceleration over long (multi-picosecond) time-scales and allows for proton energies to be achieved far beyond what the well-established scalings of proton acceleration via TNSA would predict at these modest intensities. Furthermore, the characteristics of the ARC laser (large ~100 μ m diameter focal spot, flat spatial profile, multi-picosecond, relatively low prepulse) provide acceleration conditions that allow for the investigation of 1D-like particle acceleration. A high flux ~50 J of laser-accelerated protons is experimentally demonstrated. In conclusion, a new capability in multi-picosecond particle-in-cell simulation is applied to model the data, corroborating the high proton energies and elucidating the physics of multi-picosecond particle acceleration.

43 PARTICLE ACCELERATORS↗

Evidence for Crystalline Structure in Dynamically-Compressed Polyethylene up to 200 GPa

Abstract We investigated the high-pressure behavior of polyethylene (CH 2 ) by probing dynamically-compressed samples with X-ray diffraction. At pressures up to 200 GPa, comparable to those present inside icy giant planets (Uranus, Neptune), shock-compressed polyethylene retains a polymer crystal structure, from which we infer the presence of significant covalent bonding. The A 2 /m structure which we observe has previously been seen at significantly lower pressures, and the equation of state measured agrees with our findings. This result appears to contrast with recent data from shock-compressed polystyrene (CH) at higher temperatures, which demonstrated demixing and recrystallization into a diamond lattice, implying the breaking of the original chemical bonds. As such chemical processes have significant implications for the structure and energy transfer within ice giants, our results highlight the need for a deeper understanding of the chemistry of high pressure hydrocarbons, and the importance of better constraining planetary temperature profiles.

36 MATERIALS SCIENCE↗

X-ray analysis methods for sources from self-modulated laser wakefield acceleration driven by picosecond lasers

A versatile set of methods for analyzing x-ray energy spectra and photon flux has been developed for laser plasma accelerator experiments driven by picosecond lasers. Forward fit provides extrapolated broad energy spectrum measurements, while Ross pair and differential average transmission analysis provide directly measured data points using a particular diagnostic. Combining these methods allows the measurement of x-ray energy spectra with improved confidence. We apply here the methods to three diagnostics (filter wheel, stacked image plate spectrometer, and step wedge), each sensitive to a different region of x-ray energies (<40 keV, 35–100 keV, and 60–1000 keV, respectively), to characterize the analysis methods using laser-driven bremsstrahlung x-rays. We then apply the methods to measure three x-ray mechanisms, betatron, inverse Compton scattering, and bremsstrahlung, driven by a laser plasma accelerator. The analysis results in the measurement of x-ray energy spectra ranging from 10 keV to 1 MeV with peak flux greater than 10 10 photons/keV/Sr. The combined analysis methods provide a robust tool to accurately measure broadband x-ray sources (keV to MeV) driven by laser plasma acceleration with picosecond, kilojoule-class lasers.

47 OTHER INSTRUMENTATION↗

A 3D dynamic model to assess the impacts of low-mode asymmetry, aneurysms and mix-induced radiative loss on capsule performance across inertial confinement fusion platforms

A simple 3D dynamic model for inertial confinement fusion (ICF) implosions has been developed and used to assess the impacts of low-mode asymmetry, aneurysms and mix-induced radiative loss on capsule performance across ICF platforms. While benchmarked against radiation hydrodynamics simulations, this model benefits from simplicity and speed to allow rapid assessment of possible sources of degradation as well as to help build intuition about the relative importance of different effects. Degradations in the model result from 3D pr areal density perturbations that grow under deceleration from a radial stagnation flow, resulting in reduced convergence, stagnation pressure and temperature. When available, experimental data are used as input to seed 3D perturbations in the model so that the actual observed hotspot and shell areal density asymmetry at stagnation, as well as the radiation loss increase from mix impurities, are accurately reproduced. This model is applied to a broad set of implosion data from the NIF and Omega, including examples from both indirect drive and direct drive. The model matches most experimental observables and explains major performance degradation mechanisms which can result in 30–100-fold reductions in yield. We investigate a modified ignition criterion that accounts for the increase in expansion pdV work, due to the presence of 3D pr perturbations and loss-of-confinement in thin regions of the shell.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liquid Structure of Shock-Compressed Hydrocarbons at Megabar Pressures

We present here results for the ionic structure in hydrocarbons (polystyrene, polyethylene) that were shock compressed to pressures of up to 190 GPa, inducing rapid melting of the samples. The structure of the resulting liquid is then probed using in situ diffraction by an x-ray free electron laser beam, demonstrating the capability to obtain reliable diffraction data in a single shot, even for low-Z samples without long range order. The data agree well with ab initio simulations, validating the ability of such approaches to model mixed samples in states where complex interparticle bonds remain, and showing that simpler models are not necessarily valid. While the results clearly exclude the possibility of complete carbon-hydrogen demixing at the conditions probed, they also, in contrast to previous predictions, indicate that diffraction is not always a sufficient diagnostic for this phenomenon.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗