High-Throughput falling ball viscometer for measuring High-Temperature molten salts
Not Available
Engineering topics
Publications and source records attributed to Pal, Uday.
Not Available
The local atomic structure of NaF-ZrF 4 (53–47 mol%) molten system and its evolution with temperature are examined with x-ray scattering measurements which are then used to validate the quality of ab initio and neural network-based molecular dynamics (NNMD) calculations in the temperature range 515–700°C. The machine-learning enhanced NNMD calculations offer improved efficiency while maintaining accuracy at higher distances compared to ab initio calculations. Looking at the evolution of the pair distribution function with increasing temperature, a fundamental change in the liquid structure within the selected temperature range, accompanied by a slight decrease in overall correlation is revealed. NNMD calculations indicate the coexistence of three different fluorozirconate complexes: [ZrF 6 ] 2– , [ZrF 7 ] 3– , and [ZrF 8 ] 4– , with a shift in the dominant coordination state from the 7-coordinated Zr cation toward a 6-coordinated cation with increasing temperature. The study also highlights the metastability of different local coordination structures, with frequent interconversions between the 6- and 7-coordinate states. Analysis of the Zr-F-Zr angular distribution function reveals the presence of both “edge-sharing” and “corner-sharing” fluorozirconate complexes with specific bond angles and distances in accord with previous studies, while the next-nearest-neighbor cation-cation correlations demonstrate a clear preference for unlike cations as nearest-neighbor pairs, emphasizing nonrandom arrangement. Finally, these findings contribute to a comprehensive understanding of the complex local structure of the molten salt, providing insights into temperature-dependent preferences and correlations within the molten system.
Not Available
Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.
Abstract Chromium poisoning of the air electrode remains an obstacle to the long-term performance of solid oxide fuel cells (SOFCs). In Sr-doped LaMnO3 (LSM) air electrodes, the poisoning process results in two types of deposits, chromium oxide (Cr2O3), and Mn, Cr spinel (MnCr2O4). The former forms electrochemically and the latter forms via a chemical reaction. By applying a small anodic reverse bias, Cr2O3 deposits can be removed because their formation is electrochemical in nature. However, MnCr2O4 deposits remain because their formation is chemical, rather than electrochemical, in nature. In situ chemical decomposition of the Mn, Cr spinel was investigated as an alternate removal method as thermodynamics supports its decomposition into constituent oxides below ∼540 °C in pure oxygen. The spinel decomposition process was characterized using thermogravimetric and X-ray diffraction analyses. The experimentally determined rate of spinel decomposition was undetectable (very slow) with isolated MnCr2O4 powders. The addition of 10 mol% gadolinia doped ceria (GDC) and silver powders significantly increased the rate of decomposition. However, the rate is limited by the diffusion of oxygen through the decomposed oxide layer. Although one strategy may be the addition of GDC and silver to the LSM air electrode to enhance spinel decomposition, the more effective mitigation strategy would be to prevent the formation of MnCr2O4 spinel in the first place through the removal of the reactants: Cr2O3 via electrochemical cleaning and mobile Mn ions in the zirconia electrolyte by incorporating a diffusion barrier layer such as GDC between the air electrode and electrolyte.
This project aimed to demonstrate a new molten salt electrodeposition process to go straight from low-cost silica at $200/tonne ($40¢/kg Si basis) to polysilicon in a single step using less than 30 kWh/kg. This would eliminate the carbothermic reduction step and all direct greenhouse emissions, along with 90% of the energy. It would also eliminate the chemical hazards of chlorosilane handling which have resulted in multiple fatalities in the polysilicon industry – in Japan, the US and China. This project had the following major accomplishments: Stakeholder engagement indicated that the solar silicon market is very sensitive to price, provided quality is sufficient. The most important measure of silicon quality is not purity but carrier lifetime, as many impurities can reduce performance at concentrations too small to measure; Experiments set a baseline of current efficiency which is too low for commercial application (~3%), with electronic current ruled out as a mechanism for reduced current efficiency; A scale-up plant narrative narrative described a potential plant and formed the basis for the TEA components; TEA showed that current efficiency, large cell size, and zirconia membrane lifetime are key factors which determine capital and operating costs for the process.
Chromium (Cr) poisoning remains a significant issue in long-term solid oxide fuel cell (SOFC) operation. While the addition of Cr in the interconnect and balance-of-plant (BOP) materials is effective in improving their resistance to oxidation, it also causes the deposition of resistive phases in the air electrode and thus cell performance loss. Previous work has investigated the mitigation of chromium deposition using getters, Cr diffusion resistant coatings, and more chromium-tolerant air electrode materials. However, these mitigation strategies merely postpone the degradation of performance due to Cr poisoning. Additionally, some strategies require the replacement of components, e.g., use of getters. Here we investigated a new, in-situ Cr poisoning mitigation strategy.
The overall objective was to infiltrate anodes with nanoparticle catalysts so that anode catalytic performance can be improved as anode operation temperature is reduced from 800°C to intermediate temperatures of 700°C and 600°C and as anode fuel utilization is increased. The addition of nickel nanoparticle catalysts into the anode improves performance by providing additional triple phase boundaries (TPBs), increasing the density of electrochemical reaction sites. To achieve this goal, both liquid phase and vapor phase methods for depositing nickel nanoparticles in the anode active layer, the region of the anode near the electrolyte where the electrochemical reaction occurs. It is imperative that nanoparticles are stable against coarsening during long-term operation, so the mechanisms and kinetics of nanoparticle stability during cell operation will be investigated. Finally, priority is given to processes that are scalable and easily transferable to industry, leveraging existing Ni-YSZ cermet anode technology. Utilizing nickel nanoparticles at different temperatures has different considerations that will be addressed. At the upper end of the intermediate temperature range (800°C), it is important that performance improvement is maintained over long periods by mitigating the instability of nanoparticles. At the middle of the temperature range (700°C), it is important that performance improvement is maintained at high fuel utilizations. At the lower end of the temperature range (600°C), where the performance of cells is poor due to increased resistances, it is important to improve anode performance by significantly increasing the electrochemical reaction site density, while nanoparticle durability is less of an issue. Finally, the objective was to explore mixed ionic and electronic (MIEC) nanoparticle catalysts like GDC to see if 2-phase boundaries can be created to increase the electrochemical reactions at the anode.
Infiltration of nanoscale electrocatalysts into Ni/yttria-stabilized zirconia (Ni-YSZ) cermets has been shown to improve the electrochemical performance of solid oxide fuel cell (SOFC) anodes. While infiltrated electrodes in SOFCs result in improved cell performance, long-term operation leads to coarsening of the infiltrated nanoparticles and negates the short-term performance improvements. This study explores the roles of humidity, temperature, and number of cycles of nanocatalyst infiltration in improving mixed conduction within the Ni-YSZ electrode. Two mixed conduction phases were studied: Gd 0.1 Ce 0.9 O 2-δ (GDC) as an infiltrant into Ni-YSZ electrodes, and Ni/transition metal doped-YSZ electrodes infiltrated with Ni. Analysis of impedance data from these cells shows improved electrochemical performance in infiltrated cells with mixed conduction compared with infiltrated cells containing purely ionic and electronic conducting phases. Improved anode performance is attributed to the availability of electronic pathways through predominantly ionic-conducting phases to connect distant Ni nanoparticles and/or Ni grains.
Chromium poisoning of the cathode remains a significant obstacle to the stable long-term performance of solid oxide fuel cells. This study reports, a quick, in-situ mitigation method, called electrochemical cleaning. By applying a mild anodic bias, the electrochemical deposition reactions of chromium-containing species are reversed. Chromium vapor species are formed, freeing active electrochemical sites in the air electrode. An LSM/YSZ-based cell was exposed to Cr vapors at 800ºC and then subjected to electrochemical cleaning. Cell performance recovery was evidenced by current-voltage and EIS measurements. Chromium removal was verified using SEM and EDS analyses. The cyclability of the electrochemical cleaning was tested by repeated poisoning and cleaning of another cell. Investigation into the effect of cell operating parameters (current density and cell temperature) on the rate of cleaning is discussed.
A new process is presented for low-cost one-step production of pure solid silicon from natural quartzite by molten salt electrolysis. At a process temperature of 1100°C, a techno-economic model including detailed mass and energy balances estimates energy consumption below 15 kWh/kg, with operating cost of $\$1.74$/kg and capital cost around $\$10,500$ per t/a (tonne annually) of production capacity for a 160,000 t/a plant. Use of an inert solid oxide membrane anode results in a pure oxygen by-product and no direct emissions. As a result, finite element analysis estimates the current density distribution and total current to inform the design of slab-shaped solid silicon cathodes.
Not Available
Mitigating activation polarization in the anode is one of the major challenges in intermediate-temperature operation of solid oxide fuel cells (SOFCs). Liquid phase infiltration of nanoscale electrocatalysts has been shown to result in significant reductions in activation polarization in SOFC anodes. In this study, we explore liquid-phase infiltration of nickel, gadolinium doped ceria (GDC), and Ni/GDC electrocatalysts into two different types of cermet anodes: one with a conventional Ni-YSZ composition, and the other with a Ni-MIEC cermet anode where the YSZ has been doped with 3 mol% TiO 2 to impart electronic conductivity. The principal goal of this study is to explore the role of electronic transport in the MIEC phase in effective utilization of the infiltrated nanoscale electrocatalysts. The role of temperature, infiltration cycles and the type of electrocatalysts have been experimentally studied in symmetric cells using electrochemical impedance spectroscopy (EIS). Distribution of relaxation times (DRT) modeling has been used to elucidate the contributions of various charge transfer processes.
Chromium poisoning is one of the primary factors that affect solid oxide fuel cell (SOFC) durability. In this study, an electrochemical cleaning method has been employed to reverse the effects of chromium poisoning. Two cells were fabricated and poisoned under identical conditions by operating them at 800°C in the presence of a Cr source. Both poisoned cells exhibited a significant reduction in maximum power density and an increase in polarization resistance. One of the poisoned cells, designated as the baseline cell, was cooled to room temperature after poisoning. Microstructural observation of the baseline cell showed significant contamination of the cathode active layer by chromium oxide and (Cr,Mn) spinel deposits. The other poisoned cell was electrochemically cleaned for two hours under a mild electrolytic condition. As a result of the electrochemical cleaning process, the chromium oxide deposits were substantially removed leading to a significant reduction of Cr concentration in the cathode, especially at the cathode/electrolyte interface. Furthermore, a substantial fraction of the cell performance loss was also reversed. To the best of our knowledge, this is a first demonstration of reversing the effects of chromium poisoning using a rapid in-situ process.
The infiltration of nanoparticle electrocatalysts into solid oxide fuel cell (SOFC) electrodes has been proven to produce a high density of electrochemically active sites, and reduce charge transfer polarization losses for SOFC electrodes. This is crucial for intermediate temperature operation, as these losses increase greatly at lower temperatures. Nickel-yttria stabilized zirconia (NiYSZ) cermets are low-cost, and exhibit excellent stability, but their main disadvantage stems from nickel coarsening and performance loss over their operational lifetimes. Infiltration of electrocatalyst nanoparticles has been shown to mitigate nickel coarsening and the consequent anode degradation. In this study, the effects of these infiltrants are observed in a standard Ni-YSZ electrode. In addition to nickel, mixed ionic and electronic conducting (MIEC) phases were infiltrated into Ni-YSZ scaffolds and their performances were characterized using electrochemical impedance spectroscopy (EIS). Cross-sectional microscopy of fractured cells was used to compare electrode microstructure and particle statistics. A model is proposed for how the nanoparticle electrocatalysts improve the anode performance.