Engineering topics

Pal, Uday B.

Publications and source records attributed to Pal, Uday B..

4 records

DOE OSTI2022

Quantifying the Relationship Between Microstructure and Performance in Gadolinium-Doped Ceria Infiltrated Ni/YSZ Symmetric Cells

Infiltration of mixed ionic/electronic conducting (MIEC) nanocatalysts into the anodes of solid oxide fuel cells (SOFCs) allow the hydrogen oxidation reaction (HOR) to occur at double-phase boundaries (DPBs), rather than being confined only to the triple phase boundaries (TPBs). In this research, we use a combination of cross-sectional scanning electron microscopy (SEM), three-dimensional (3-D) reconstruction, and electrochemical methods to characterize both baseline and gadolinium-doped ceria (GDC)-infiltrated symmetric cells, with the goal of establishing a comparison between the density of electrochemically active sites in uninfiltrated and GDC-infiltrated cells. Here, electrochemical impedance spectroscopy (EIS) and distribution of relaxation times (DRT) analysis showed GDC infiltration decreased the overall polarization of the anode by a factor of 8.78 X, and decreased the resistance associated with the reactions at the TPBs/DPBs by a factor of over 21 X. By quantifying expected GDC deposition morphology in the Ni/YSZ anode it is estimated that reactions occur in the baseline cell up to 84 nm from the active TPB lines.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Quantifying Percolated Triple Phase Boundary Density and Its Effects on Anodic Polarization in Ni-Infiltrated Ni/YSZ SOFC Anodes

Increasing the density of percolated triple phase boundaries (TPBs) by infiltrating nanoscale electrocatalysts can improve the performance of solid oxide fuel cell (SOFC) anodes. However, the complex microstructure of these infiltrated nanocatalysts creates challenges in quantifying their role in anode performance improvements. In this research, scanning electron microscopy of fractured cross-sections of a Ni-nanocatalyst infiltrated anodic symmetric cell along with three-dimensional (3-D) reconstruction of the same anode have been used to quantify the changes in percolated TPB densities due to infiltration. This change in percolated TPB density has been compared to the improvement in anode activation polarization resistance measured by electrochemical impedance spectroscopy (EIS). It was found that increased TPB densities only partially accounted for the measured performance improvement. Distribution of relaxation times (DRT) analyses showed that a reduction in the time constants of the catalytic processes in the anode also play a role, suggesting that the added nanoscale percolated TPB boundaries are more electrochemically active as compared to the cermet TPB boundaries.

25 ENERGY STORAGE↗

DOE OSTI2020

Experimental validation of solid oxide fuel cell polarization modeling: An LSM-YSZ/YSZ/Ni-YSZ case study

Polarization modeling based on the measured I-V curves is a useful tool for analyzing SOFC performance and diagnosing performance limitations. Using the polarization model, the overpotential of a cell is usually separated into different polarization contributions, including area specific ohmic polarization, activation polarization, and anodic and cathodic concentration polarizations. In this study, we aim to experimentally validate the accuracy of the polarization model. As a case study, anode-supported cells with LSM-YSZ/YSZ/Ni-YSZ configuration are used. By curve-fitting the I-V curves of a cell tested under different cathode oxygen partial pressures into the polarization model, the contributions of different polarization losses are quantified. To validate the polarization model, independent experiments/studies including electrochemical impedance spectroscopy, cathode kinetics study, ex-situ diffusivity measurement, and tortuosity measurement using 3D reconstructed anode are conducted. The results from polarization modeling and from validation studies are in good agreement, thereby validating the polarization model for SOFC performance analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Comparison of chromium poisoning between lanthanum strontium manganite and lanthanum strontium ferrite composite cathodes in solid oxide fuel cells

Degradation mechanisms of chromium poisoning have been extensively investigated for last two decades on various cathode materials for solid oxide fuel cells. While most researchers used half-cell experiments to investigate the effects of chromium impurities, this paper compares the degradation phenomena of LSM-YSZ and LSF-GDC cathodes in full cells under different operating conditions, namely polarized current density and humidity over the cathode. Under cathodic load, performance degradation of LSF-GDC cathode is significantly less than that of LSM-YSZ cathode. Most interestingly, under humidified air condition, LSF-based cell hardly experiences performance degradation while LSM-based cell shows a catastrophic degradation. Cr deposition in LSM-based cells occurs mainly near the electrolyte under both dry and humidified air conditions. In contrast, Cr deposition in LSF-based cell concentrates at the cathode surface under dry air condition, but concentrates both at cathode surface and near electrolyte under humidified air condition. Microstructure analysis reveals Mn-associated Cr deposits in LSM-based cathode, and Sr- and Fe-associated Cr deposits in LSF-based cathode. With the help of distribution of relaxation time analysis, the different electrochemical behaviors of LSM- and LSF-based cells are carefully interpreted. The effects of electrochemical deposition, Sr surface segregation, and humidity on LSM- and LSF-based cathodes are discussed.

25 ENERGY STORAGE↗