Engineering topics

Palmer, Eric

Publications and source records attributed to Palmer, Eric.

7 records

NASA NTRS2020

Operational Techniques for Dealing with Long Eclipses During the MMS Extended Mission

Launch window design for the Magnetospheric Multiscale (MMS) mission ensured that no excessive eclipses would be encountered during the prime mission. However, no orbit solutions exist that satisfy the eclipse constraints indefinitely: most extended mission years contain 1-3 eclipses long enough to potentially damage either the spacecraft or its scientific instruments. Two steps were taken to improve the situation. Firstly, raising apogee radius from 25 to 29.34 Earth radii altered the Sun-Earth-MMS phasing, so efficiently achieving reductions in the long eclipse durations. These maneuvers were performed early this year, in preparation for the first pair of long eclipses in August 2019. Secondly, a set of operational steps were taken around the time of the eclipses to help maintain spacecraft and instrument temperatures while preventing power load shedding. These operational steps included raising key onboard temperatures through adjusting the spacecraft attitude to tilt the instrument deck towards the Sun, and engaging select heaters prior to going into eclipses. In addition, all scientific instruments were turned off, as well as high-power, non-critical spacecraft systems, to conserve energy.These steps each came with trade-offs which will be discussed in the paper. Finally, the results that were obtained when the spacecraft experienced the first extremely long eclipses will be discussed, as will lessons learned for future long eclipses.

Williams, Trevor↗

NASA NTRS2020

Osiris-Rex Shape Model Performance During the Navigation Campaign

The Navigation Campaign of the OSIRIS-REx mission began when the first image of Bennu was recorded by the PolyCam high-resolution imager on Au-gust 17, 2018. In the ensuing months, two teams began building shape models based on imagery taken during the Approach and Preliminary survey phases to be used for the transition to landmark navigation in the Orbital A phase. The orbit determination team began analyzing and characterizing the performance and errors associated with each shape model delivery working closely to iterate on the next shape model delivery. By the end of Orbital A, shape models produced by the Altimetry Working Group and JPL exceeded pre-launch performance re-quirements. This paper provides a summary of the analysis performed during operations.

Leonard, Jason M.↗

NASA NTRS2019

Lunisolar Perturbations of High-Eccentricity Orbits Such as the Magnetospheric Multiscale Mission

For highly eccentric orbits such as that of the Magnetospheric Multiscale (MMS)mission, with apogee radius now 29.34 Earth radii, the third-body effects of Sun andMoon are the major perturbations. One key consequence is an oscillation in MMSperigee altitude, on an approximately 6 year cycle. This variation has already requiredperigee-raise maneuvers to avoid an untimely reentry. There is also a long-termevolution in the orientation of the MMS orbit, with period roughly twice as long. Thiseffect may potentially be useful for MMS science studies, as it can bring the spacecraftinto new regions of the magnetosphere.

Williams, Trevor↗

NASA NTRS2018

MMS Extended Mission Design: Evaluation of a Lunar Gravity Assist Option

This paper will describe a study that was carried out on the design of a set of maneuvers that were considered for the later stages of an extended mission of the Magnetospheric Multiscale (MMS) mission. The goal of these maneuvers was to put MMS into a significantly different orbit from those flown heretofore, so allowing science collection in a different region of the magnetosphere. This study was made feasible by the fact that the rate at which fuel is being consumed to maintain small formations on the MMS high-apogee orbit is less than expected pre-flight: the current consumption rate is only about 2 kg/yr/spacecraft. In addition, the spacecraft finished the prime mission with a significant amount of fuel remaining: this was about 1-sigma above the mean when compared with pre-launch Monte Carlo simulations. The resulting situation is similar to that of a libration orbit mission, where station-keeping requires so little fuel that any margin at all will lead to an extensive mission lifetime. In the case of MMS, the spacecraft could, if desired, perform formation flying in the current orbit for several decades. Alternatively, the spacecraft could use a significant fraction of the remaining fuel to perform major orbit modifications, while still leaving enough to conduct formation flying for on the order of a decade. The extended mission maneuvers studied here are further apogee-raises, with the goal of setting up one or more lunar gravity assists. Geometry dictates that a lunar encounter is only achievable when the MMS apogee vector lies approximately in the lunar orbit plane: this limits the possible dates to mid-2021 or early 2027.

Design↗

NASA NTRS2017

Satellite Formation Flight Results from Phase 1 of the Magnetospheric Multiscale Mission

This paper describes the underlying dynamics of formation flying in a high-eccentricity orbit such as that of the Magnetospheric Multiscale mission. The GPS-based results used for MMS navigation are summarized, as well as the procedures that are used to design the maneuvers used to place the spacecraft into a tetrahedron formation and then maintain it. The details of how to carry out these maneuvers are then discussed. Finally, the numerical results that have been obtained concerning formation flying for the MMS mission to date (e.g. tetrahedron sizes flown, maneuver execution error, fuel usage, etc.) are presented in detail.

satellite formation flight↗

NASA NTRS2016

Initial Satellite Formation Flight Results from the Magnetospheric Multiscale Mission

This paper describes the underlying dynamics of formation flying in a high-eccentricity orbit such as that of the Magnetospheric Multiscale mission. The GPS-based results used for MMS navigation is summarized, as well as the procedures that are used to design the maneuvers used to place the spacecraft into a tetrahedron formation and then maintain it. The details of how to carry out these maneuvers are then discussed. Finally, the numerical results that have been obtained concerning formation flying for the MMS mission to date (e.g. tetrahedron sizes flown, maneuver execution error, fuel usage, etc.) are presented in detail.

Conjunction↗

NASA NTRS2016

Initial Satellite Formation Flight Results from the Magnetospheric Multiscale Mission

This paper will describe the results that have been obtained to date concerning MMS formation flying. The MMS spacecraft spin at a rate of 3.1 RPM, with spin axis roughly aligned with Ecliptic North. Several booms are used to deploy instruments: two 5 m magnetometer booms in the spin plane, two rigid booms of length 12.5 m along the positive and negative spin axes, and four flexible wire booms of length 60 m in the spin plane. Minimizing flexible motion of the wire booms requires that reorientation of the spacecraft spin axis be kept to a minimum: this is limited to attitude maneuvers to counteract the effects of gravity-gradient and apparent solar motion. Orbital maneuvers must therefore be carried out in essentially the nominal science attitude. These burns make use of a set of monopropellant hydrazine thrusters: two (of thrust 4.5 N) along the spin axis in each direction, and eight (of thrust 18 N) in the spin plane; the latter are pulsed at the spin rate to produce a net delta-v. An on-board accelerometer-based controller is used to accurately generate a commanded delta-v. Navigation makes use of a weak-signal GPS-based system: this allows signals to be received even when MMS is flying above the GPS orbits, producing a highly accurate determination of the four MMS orbits. This data is downlinked to the MMS Mission Operations Center (MOC) and used by the MOC Flight Dynamics Operations Area (FDOA) for maneuver design. These commands are then uplinked to the spacecraft and executed autonomously using the controller, with the ground monitoring the burns in real time.

satellite↗