Search NASA⌕ Search

Engineering topics

Palmer, G. E.

Publications and source records attributed to Palmer, G. E..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Modeling Heatshield Erosion Due to Dust Particle Impacts for a Martian Entry Vehicle

Because planetary missions to Mars take years from initial design to arrival at Mars, and because of the unpredictability of major global dust storms, the de-sign of the thermal protection system (TPS) of a Mars entry vehicle requires an estimation for the potential damage caused by dust particle impacts on the heat-shield. This paper will review previous analytical and experimental approaches to modeling dust particle ero-sion and will compare the legacy models against more modern computational techniques and new dust ero-sion models that will be based on upcoming experi-ments in the German Aerospace Center (DLR) GBK facility. The various models will be compared by incorporating them into the Icarus material response code applied to a representative vehicle entering the Martian atmosphere.

planetary entry↗
NASA NTRS2019

Overview of Heatshield for Extreme Entry Environment Technology (HEEET)

The objective of the Heatshield for Extreme Entry Environment Technology (HEEET) projects is to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations such as Venus and Saturn. Destinations that have extreme entry environments with heat fluxes > 3500 W/sq cm and pressures up to 5 atmospheres, entry environments that NASA has not flown since Pioneer-Venus and Galileo. The scope of the project is broad and can be split into roughly four areas, Manufacturing/Integration, Structural Testing and Analysis, Thermal Testing and Analysis and Documentation. Manufacturing/Integration covers from raw materials, piece part fabrication to final integration on a 1-meter base diameter 45-degree sphere cone Engineering Test Unit (ETU). A key aspect of the project was to transfer as much of the manufacturing technology to industry in preparation to support future mission infusion. The forming, infusion and machining approaches were transferred to Fiber Materials Inc. and FMI then fabricated the piece parts from which the ETU was manufactured.

Thermal Protection System↗
NASA NTRS2019

Modeling Heatshield Erosion due to Dust Particle Impacts for a Martian Entry Vehicle

New surface damage models are presented that predict the heat shield erosion due to dust particle impact when a spacecraft enters the Martian atmosphere. Existing models were based on Apollo-era experimental data and approximate methods for tracking the dust particle trajectories through the shock layer. These legacy methods will be compared against new results based on more sophisticated particle tracking methods and recent experimental data.

Planetary entry↗
NASA NTRS1993

Trajectory based, 3-dimensional heating and ablation calculations for the Apollo Lunar/Earth return capsule

Three dimensional (3-D) surface heating and ablation rate distributions have been obtained based on the geometry of the project Apollo Lunar/Earth return capsule and high Reynolds number inviscid/boundary layer methods. This application is based on the principles of the pseudo-three dimensional axisymmetric streamline analogy. Inviscid surface streamlines are determined for the forebody portion of the Apollo capsule using a CFD solver. Streamlines are obtained for the 20 deg angle-of-attack flight case, and the associated streamline metrics are determined. Boundary layer heating and ablation calculations are performed along selected Apollo forebody streamlines using the non-similar boundary layer code. Surface radiative heating estimates were obtained and the validity of the streamline tracing analogy is examined. These comparisons and the Apollo trajectory heating results are discussed.

Henline, W. D.↗
NASA NTRS1990

Earth atmospheric entry studies for manned Mars missions

Decelerations, heating rates, and total heat loads encountered when returning from Mars to earth at entry speeds of 12 km/sec to 16 km/sec are studied. For entry at 14 km/sec, it is found that a lift/drag ratio (L/D) of 0.5 is required to provide a guidance corridor margin near 1 deg for the specified deceleration limit of 5 g. For a blunted, raked cone with an L/D = 0.5, the peak heating rate near the aft end of the forebody varies from 0.14 to 0.23 kW/sq cm for laminar flow. If ablation triggers boundary layer transition, the peak heating can rise to 0.5 or up to 0.72 kW/sq cm. All heating rates are sufficiently high to make ablative heat shields necessary.

Tauber, M. E.↗
NASA NTRS1985

Comparison of calculated and measured velocities near the tip of a model rotor blade at transonic speeds

The ability of the ROT22 code to predict accurately the transonic flow field in the crucial region around and beyond the tip of a high speed rotor blade was assessed. The computations were compared with extensive laser velocimetry measurements made at zero advance ratio and tip Mach numbers of 0.85, 0.88, 0.90, and 0.95. The comparison between theory and experiment was made using 300 scans for the three orthogonal velocity components covering a volume having a height of over one blade chord, a width of nearly two chords, and a length ranging from about 1 to 1.6 chords, depending on the tip speeds. The good agreement between the calculated and measured velocities established the ability of the code to predict the off blade flow field at high tip speeds. This supplements previous comparisons where surface pressures were shown to be well predicted on two different tips at advance ratios to 0.45, especially at the critical 90 deg azimuth blade position. These results demonstrate that the ROT22 code can be used with confidence to predict the important tip region flow field including the occurrence, strength, and location of shock waves causing high drag and noise.

Tauber, M. E.↗