Engineering topics

Palumbo, D. L.

Publications and source records attributed to Palumbo, D. L..

11 records

NASA NTRS1997

Optimizing an Actuator Array for the Control of Multi-Frequency Noise in Aircraft Interiors

Techniques developed for selecting an optimized actuator array for interior noise reduction at a single frequency are extended to the multi-frequency case. Transfer functions for 64 actuators were obtained at 5 frequencies from ground testing the rear section of a fully trimmed DC-9 fuselage. A single loudspeaker facing the left side of the aircraft was the primary source. A combinatorial search procedure (tabu search) was employed to find optimum actuator subsets of from 2 to 16 actuators. Noise reduction predictions derived from the transfer functions were used as a basis for evaluating actuator subsets during optimization. Results indicate that it is necessary to constrain actuator forces during optimization. Unconstrained optimizations selected actuators which require unrealistically large forces. Two methods of constraint are evaluated. It is shown that a fast, but approximate, method yields results equivalent to an accurate, but computationally expensive, method.

Palumbo, D. L.↗

NASA NTRS1996

Performance of Optimized Actuator and Sensor Arrays in an Active Noise Control System

Experiments have been conducted in NASA Langley's Acoustics and Dynamics Laboratory to determine the effectiveness of optimized actuator/sensor architectures and controller algorithms for active control of harmonic interior noise. Tests were conducted in a large scale fuselage model - a composite cylinder which simulates a commuter class aircraft fuselage with three sections of trim panel and a floor. Using an optimization technique based on the component transfer functions, combinations of 4 out of 8 piezoceramic actuators and 8 out of 462 microphone locations were evaluated against predicted performance. A combinatorial optimization technique called tabu search was employed to select the optimum transducer arrays. Three test frequencies represent the cases of a strong acoustic and strong structural response, a weak acoustic and strong structural response and a strong acoustic and weak structural response. Noise reduction was obtained using a Time Averaged/Gradient Descent (TAGD) controller. Results indicate that the optimization technique successfully predicted best and worst case performance. An enhancement of the TAGD control algorithm was also evaluated. The principal components of the actuator/sensor transfer functions were used in the PC-TAGD controller. The principal components are shown to be independent of each other while providing control as effective as the standard TAGD.

Palumbo, D. L.↗

NASA NTRS1996

Performance of Optimized Actuator and Sensor Arrays in an Active Noise Control System

Experiments have been conducted in NASA Langley s Acoustics and Dynamics Laboratory to determine the effectiveness of optimized actuator/sensor architectures and controller algorithms for active control of harmonic interior noise. Tests were conducted in a large scale fuselage model - a composite cylinder which simulates a commuter class aircraft fuselage with three sections of trim panel and a floor. Using an optimization technique based on the component transfer functions, combinations of 4 out of 8 piezoceramic actuators and 8 out of 462 microphone locations were evaluated against predicted performance. A combinatorial optimization technique call tabu search was employed to select the optimum transducer arrays. Three test frequencies represent the cases of a strong acoustic and strong structural response, a weak acoustic and strong structural response and a strong acoustic and weak structural response. Noise reduction was obtained using a Time Averaged/Gradient Descent (TAGD) controller. Results indicate that the optimization technique successfully predicted best and worst case performance. An enhancement of the TAGD control algorithm was also evaluated. The principal components of the actuator/sensor transfer functions were used in the PC-TAGD controller. The principal components are shown to be independent of each other while providing control as effective as the standard TAGD.

Palumbo, D. L.↗

NASA NTRS1986

A performance evaluation of the software-implemented fault-tolerance computer

The results of a performance evaluation of the Software-Implemented Fault-Tolerance (SIFT) computer system conducted in the NASA Avionics Integration Research Laboratory are presented. The essential system functions are described and compared to both earlier design proposals and subsequent design improvements. Using SIFT's specimen task load, the executive tasks, such as reconfiguration, clock synchronization, and interactive consistency, are found to consume significant computing resources. Together with other system overhead (e.g., voting and scheduling), the operating system overhead is in excess of 60 percent. The authors propose specific design changes that reduce this overhead burden significantly.

Palumbo, D. L.↗

NASA NTRS1986

The fault-tolerant multiprocessor computer

The development and evaluation of fault-tolerant computer architectures and software-implemented fault tolerance (SIFT) for use in advanced NASA vehicles and potentially in flight-control systems are described in a collection of previously published reports prepared for NASA. Topics addressed include the principles of fault-tolerant multiprocessor (FTMP) operation; processor and slave regional designs; FTMP executive, facilities, acceptance-test/diagnostic, applications, and support software; FTM reliability and availability models; SIFT hardware design; and SIFT validation and verification.

Smith, T. B., III↗

NASA NTRS1985

Measurement of SIFT operating system overhead

The overhead of the software implemented fault tolerance (SIFT) operating system was measured. Several versions of the operating system evolved. Each version represents different strategies employed to improve the measured performance. Three of these versions are analyzed. The internal data structures of the operating systems are discussed. The overhead of the SIFT operating system was found to be of two types: vote overhead and executive task overhead. Both types of overhead were found to be significant in all versions of the system. Improvements substantially reduced this overhead; even with these improvements, the operating system consumed well over 50% of the available processing time.

Palumbo, D. L.↗

NASA NTRS1984

Software Implemented Fault-Tolerant (SIFT) user's guide

Program development for a Software Implemented Fault Tolerant (SIFT) computer system is accomplished in the NASA LaRC AIRLAB facility using a DEC VAX-11 to interface with eight Bendix BDX 930 flight control processors. The interface software which provides this SIFT program development capability was developed by AIRLAB personnel. This technical memorandum describes the application and design of this software in detail, and is intended to assist both the user in performance of SIFT research and the systems programmer responsible for maintaining and/or upgrading the SIFT programming environment.

Green, D. F., Jr.↗

NASA NTRS1983

SIFT - A preliminary evaluation

This paper presents the results of a performance evaluation of the SIFT computer system conducted in the NASA AIRLAB facility. The essential system functions are described and compared to both earlier design proposals and subsequent design improvements. The functions supporting fault tolerance are found to consume significant computing resources. With SIFT's specimen task load, scheduled at a 30-Hz rate, the executive tasks such as reconfiguration, clock synchronization and interactive consistency, require 55 percent of the available task slots. Other system overhead (e.g., voting and scheduling) use an average of 50 percent of each remaining task slot.

Palumbo, D. L.↗

NASA NTRS1981

An operations manual for the Spinning Mode Synthesizer in the Langley Aircraft Noise Reduction Laboratory

The need for a dependable and controllable noise source and the consequent development of the Spinning Mode Synthesizer (SMS) is discussed. Configuration of the SMS incorporated into the flow duct facility is reported. Turbofan noise is composed of a series of fundamental acoustical modes, which are produced by acoustic drivers equispaced circumferentially around the flow duct. Pressure field is compared to an ideal result in an optimization algorithm, adjusting driver settings until system error is minimized. The following items are included: operating instructions, a detailed description of the system, and a user's guide to data acquisition packages available.

Palumbo, D. L.↗

NASA NTRS1973

Design of a laser rangefinder for Martian terrain measurements

Three methods for using a laser for rangefinding are discussed: optical focusing, the phase difference method, and timed pulse. For application on a Mars Rover, the timed pulse method proves to be the better choice in view of the requirements set down. This is made possible by pulse expansion techniques described in detail. Initial steps taken toward building the range finder are given, followed by a conclusion.

Palumbo, D. L.↗

NASA NTRS1973

Design of a laser rangefinder for Martian terrain measurements

Methods for using a laser for rangefinding are discussed. These are: (1) Optical Focusing, (2) the Phase Difference Method, and (3) Timed Pulse. For application on a Mars Rover, the Timed Pulse Method proves to be the better choice in view of the requirements set down. This is made possible by pulse expansion techniques described in detail. Initial steps taken toward building the range finder are given, followed by a conclusion which is actually a proposal for future steps.

Palumbo, D. L.↗