Search NASA⌕ Search

Engineering topics

Pamminger, Michael

Publications and source records attributed to Pamminger, Michael.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Next-Generation NGV Driver Information System

Measuring the amount of fuel contained in the tank of a Natural Gas Vehicle (NGV) is not as straightforward as it is for a liquid-fueled vehicle. The fuel in an NGV is a compressed gas at pressures up to 4200psig, and its pressure changes with temperature. The current state-of-the-art, which is used on most NGVs, is a simple pressure gauge as a rough guide for remaining fuel. This presents a high degree of error because pressure varies widely depending on temperature. Immediately following refueling, the temperature in the vehicle’s cylinders is often greater than 150°F. As the driver pulls out of the fueling station and begins consuming gas, the pressure drops at a very fast rate due to expansion cooling of the gas. This pressure drop appears to the driver to be a very rapid decrease in fuel level, reducing trust in the fuel level indication and leading to concern about the distance the vehicle can travel before refueling again, which is known as “range anxiety.”

03 NATURAL GAS↗
DOE OSTI2024

Algorithm for Calculating Mass of Gaseous Fuels in Enclosed Containers

This algorithm estimates the mass of gaseous fuels in enclosed tanks by utilizing measurements of pressure and temperature within the tank and leveraging thermodynamic relatio nships. For vehicle applications, information available on the vehicle's Controller Area Network bus is used to estimate tank size and gas properties.

Pamminger, Michael↗
DOE OSTI2023

Modeling the impact of the fuel injection strategy on the combustion and performance characteristics of a heavy-duty GCI engine

Gasoline compression ignition (GCI) is a promising strategy to achieve high thermal efficiency and low emissions with limited modifications to the conventional diesel engine hardware. It is a partially premixed concept, which derives its superiority from higher volatility and longer ignition delay of gasoline-like fuels combined with higher compression ratio typical of diesel engines. Here, the present study investigates the combustion process in a GCI engine operating with different injection strategies using computational fluid dynamics (CFD). Simulations are carried out on a single cylinder of a multi cylinder heavy-duty compression ignition engine, which operates at a compression ratio of 17:1 and an engine speed of 1038 rev/min. Two different injection strategies viz., late injection (LI), and early pilot injection (EP) are investigated to understand their impact on combustion and performance of the engine. Renormalized group (RNG) k-ε model is used to describe in-cylinder turbulence and KH RT model is used to simulate the fuel spray breakup. The developed CFD methodology is validated against relevant experimental data under a wide range of operating conditions for each injection strategy. The developed CFD methodology was found to capture the engine combustion behavior quite well. Based on the validated CFD model, the differences in the progress of combustion event for the two injection strategies is highlighted. It was found that a larger pilot fuel mass fraction results in a steeper rise in the initial heat release rate which in turn influences the transition to mixing controlled combustion. In line with the experimental data, the study showed that the late pilot injection strategy with three injection pulses, results in higher performance compared to the other conditions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Model predictive control of mixing controlled compression ignition operation for low reactivity fuels

Using gasoline or other low reactivity fuels with a pilot injection or port fuel injection in a compression ignition engine has shown great potential in reducing NOx emissions while keeping high thermal efficiency compared to diesel. However, excessive combustion noise is caused by a high maximum pressure rise rate in the cylinder due to the higher fractions of premixed charge of the low-reactivity fuel. This noise can result in structural damage to engine components and as such, combustion noise limits the range of the operating parameters and makes the control of such engines challenging. In this study, a simulation environment was built up in MATLAB/Simulink leveraging a physics-based zero-dimension combustion model to capture the in-cylinder pressure time traces as well as metrics relevant to thermal efficiency and combustion noise. Here, in order to also facilitate the control of emissions, machine learning models were investigated to capture NOx emissions. A kernel-based extreme learning machine (K-ELM) performed best and had a coefficient of correlation (R-squared) of 0.998. The combustion and NOx emission models are valid for not only conventional gasoline fuel but also oxygenated alternative fuel blends at three different pilot injection strategies. In order to track key combustion metrics while keeping noise and emissions within constraints, a model predictive control (MPC) was applied for a compression ignition engine operating with a range of potential fuels and fuel injection strategies. The MPC is validated under different scenarios, including a load step change, fuel type change, and injection strategy change, with proportional–integral (PI) control as the baseline. The simulation results show that MPC reduces about 26% of ringing intensity in the transient process and 17% at the steady state for E30. Generally, MPC can optimize the overall performance through modifying the main injection timing, pilot fuel mass, and exhaust gas recirculation (EGR) fraction.

42 ENGINEERING↗
DOE OSTI2021

Model predictive combustion control of a Gasoline Compression Ignition engine

Gasoline Compression Ignition is a novel combustion concept that derives its superiority from the high compression ratio of a compression ignition engine as well as the properties of gasoline fuel, such as longer ignition delay and higher volatility compared to diesel. Here, this combustion concept was experimentally tested on a 12.4L Class 8 truck engine. Based on these experimental data, prior efforts by the authors focused on the development of an engine model for a heavy-duty engine operating on a low-reactivity fuel. This engine model was leveraged within this study to investigate a combustion control strategy at different engine conditions and injection methods and was augmented to incorporate cycle-to-cycle combustion variations. State estimation is performed by means of a Kalman filter which feeds into a model predictive controller. The model predictive controller chooses control actions based on a predefined cost function under consideration of bounds reflecting physical constraints. The engine model was utilized to establish a state-space model that serves the Kalman filter and model predictive controller for estimation and prediction. A comparative study investigating control actions and engine behavior was performed with and without limiting in-cylinder peak pressure as well as combustion noise, which is of particular interest for early pilot injection strategies. In addition, the proposed control architecture was investigated at two different levels of cycle-to-cycle variations and compared to the performance of a control structure with input disturbance rejection. For increased cycle-to-cycle variations, disturbance estimation reduces state fluctuations and control effort. In general, this investigation highlights control aspects specific to a compression-ignited combustion regime with low-reactivity fuel. The control algorithm is able to maintain the desired references for brake mean effective pressure and combustion phasing while controlling peak in-cylinder pressure and combustion noise.

42 ENGINEERING↗
DOE OSTI2020

Combustion, criteria pollutant and soot property assessment of mixing-controlled high-load engine operation with gasoline and diesel

Gasoline compression ignition (GCI) is an emerging technology that can achieve high fuel efficiency and low criteria emissions in diesel engine platforms using gasoline and gasoline-like fuels. While low- and mid-range loads are enabled with low temperature combustion (LTC) approaches, high-loads are more efficient with high temperature combustion (HTC) requiring mixing-controlled combustion (MCC). Lower soot emissions are achieved with gasoline even in high-load MCC than with diesel, but detailed soot properties from gasoline and diesel have been rarely discussed. In order to better understand how high-load operations affect soot properties, in this study gasoline and diesel were tested in a six-cylinder heavy duty engine at 14 bar brake mean effective pressure (BMEP) at similar combustion phasing. Effects of pilot mass ratio and EGR on heat release rates, cylinder temperatures, ignition delay (ID) and combustion duration (CD) were examined, relating with emissions variations with applications of the two fuels. Soot mass and particle number emissions were slightly lower with gasoline than with diesel, resulting in a more favorable NOx-soot trade-off with gasoline like other reports. Contrary to other findings in the literature, gasoline and diesel soot samples presented similar particle distribution shapes, carbon crystalline structures and primary particle sizes, regardless of fuel type and EGR rate. Consequently, the current result proposes that soot particles have undergone similar soot formation and oxidation processes despite reactivity difference and oxygen availability under the examined high-load MCC with similar combustion phases.

02 PETROLEUM↗
DOE OSTI2020

A control-oriented combustion model framework for compression ignition engines operating on low-reactivity fuel

This work focuses on zero-dimensional modeling of the heat release rate in a compression ignition engine operating on gasoline-like fuels. Due to the properties of gasoline, such as high volatility and longer ignition delay than diesel, the injection strategies can vary significantly from the operation with conventional diesel fuel. Different injection strategies are commonly used to achieve varying degrees of in-cylinder stratification in order to shape the combustion event and maximize efficiency. The proposed zero-dimensional combustion model was developed to account for the different stages in combustion caused by the fuel stratification. As the ignition delay model is an integral part of the entire combustion process and significantly affects the prediction accuracy, special attention has been paid to local phenomena influencing ignition delay. A one-dimensional spray model by Musculus and Kattke was employed in conjunction with a Lagrangian tracking approach in order to estimate the local air–fuel ratio within the spray tip, as a proxy for reactivity. The local air–fuel ratio, in-cylinder temperature and pressure were used in an integral fashion to estimate the ignition delay. Heat release rates were modeled using first-order non-linear differential equations. The proposed combustion model was validated against experimental data of a heavy-duty compression ignition engine with up to three injection events at mostly 1038 r/min and 14 bar brake mean effective pressure. Further validation of the model was carried out at other engine loads and speeds. Model prediction errors in CA50 of less than 1 °CA across all conditions were found. Modeling results of other combustion metrics such as combustion duration and indicated mean effective pressure are also highly satisfactory. In addition, the model has been shown to be capable of estimating the ringing intensity for most conditions.

Pamminger, Michael↗
DOE OSTI2019

Knock Intensity Distribution and a Stochastic Control Framework for Knock Control

One of the main factors limiting the efficiency of spark-ignited (SI) engines is the occurrence of engine knock. In high temperature and high pressure in-cylinder conditions, the fuel–air mixture auto-ignites creating pressure shock waves in the cylinder. Knock can significantly damage the engine and hinder its performance; as such, conservative knock control strategies are generally implemented which avoid such operating conditions at the cost of lower thermal efficiencies. Significant improvements in the performance of conventional knock controllers are possible if the properties of the knock process are better characterized and exploited in knock controller designs. One of the methods undertaken to better characterize knocking instances is to employ a probabilistic approach, in which the likelihood of knock is derived from the statistical distribution of knock intensity (KI). In this paper, it is shown that KI values at a fixed operating point for single fuel and dual fuel engines are accurately described using a mixed lognormal distribution. The fitting accuracy is compared against those for a randomly generated mixed-lognormally distributed dataset, and shown to exceed a 95% accuracy threshold for almost all of the operating points tested. Additionally, this paper discusses a stochastic knock control approach that leverages the mixed lognormal distribution to adjust spark timing based on KI measurements. Overall, this more informed knock control strategy would allow for improvements in engine performance and fuel efficiency by minimizing knock occurrences.

42 ENGINEERING↗
DOE OSTI2019

Impact of fuel and engine operating conditions on efficiency of a heavy duty truck engine running compression ignition mode using energy and exergy analysis

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low temperature combustion with low engine-out NO x and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Previous studies by the authors demonstrated that utilizing port and direct injection of E85 gasoline simultaneously resulted in the best performance and the highest brake thermal efficiency of 47.1%, which was 1.2% higher compared to diesel baseline. For further efficiency improvement, a better understanding of energy and exergy loss mechanisms is required. As such, in this work first and second law thermodynamics analysis were applied to experiments with gasoline compression ignition at an engine speed of 1038 rpm and brake mean effective pressure of 1.4 MPa on a 12.4 L multi-cylinder heavy-duty diesel engine. The impact on the efficiency, losses, and irreversibility with respect to various parameters such as fuel, injection strategy, intake condition, and port injected water mass was quantified. The peak efficiency of ideal cycles and the combined efficiency with a waste heat recovery system were also estimated in this study to assess opportunities for further efficiency gains. It was found that the combustion irreversibility was dominated by the combustion temperature rather than the fuel structure. Despite its highest brake thermal efficiency, E85 gasoline generated the highest exergy destruction due to its lowest combustion temperature. For the same reason, retarding the combustion phasing or adopting a port and direct injection strategy increased the exergy destruction. The combustion duration loss was more notable than the phasing loss and was affected by both the combustion duration and shape of heat release profile. Water port injection increased the exhaust energy, but the available energy dropped significantly attributed to the decrease in the exhaust temperature, rendering waste heat recovery ineffective. The second law analysis serves as a helpful tool in conjunction with the first law analysis to explore pathways to maximize engine efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2019

Performance, Fuel Economy, and Economic Assessment of a Combustion Concept Employing In-Cylinder Gasoline/Natural Gas Blending for Light-Duty Vehicle Applications

In current production natural gas/gasoline bi-fuel vehicles, fuels are supplied via port fuel injection (PFI). Injecting a gaseous fuel in the intake port significantly reduces the volumetric efficiency and consequently torque as compared to gasoline. In addition to eliminating the volumetric efficiency challenge, direct injection (DI) of natural gas (NG) can enhance the in-cylinder flow, mixing, and combustion process resulting in improved efficiency and performance. A computational fluid dynamics (CFD) approach to model high-pressure gaseous injection was developed and validated against X-ray data from Argonne’s Advanced Photon Source. NG side and central DI of various designs and injection strategies were assessed experimentally along with CFD correlation. Significant effects on combustion metrics were quantified and explained via improved understanding of the in-cylinder flow effects due to NG injection. On-demand in-cylinder blending using E10 PFI and NG DI provides an additional lever to adjust in-cylinder turbulence as well as knock resistance across the engine speed and load range. NG DI improves part-load dilution tolerance due to higher in-cylinder turbulence and the high knock resistance of NG compared to E10 improves wide open throttle (WOT) performance while enabling increased compression ratios (CR). Vehicle level simulations suggest that implementing this strategy on a ½ ton pick-up truck with a naturally aspirated engine at 12.5:1 CR improves energy consumption on the aggressive US06 drive cycle by 15.5% compared to E10 operation, and gives a petroleum reduction of 78% over the blended range. There are challenges regarding market acceptance and widespread adoption of dual-fuel NG-gasoline vehicle applications beyond the performance degradation when the vehicle runs out of natural gas. Furthermore, those challenges include practical concerns such as loss of cargo volume and payload due to the NG storage tank, extended NG refueling times, fueling convenience due to gasoline and NG fuel tanks, and limited NG fueling infrastructure.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2018

Influence of charge motion and compression ratio on the performance of a combustion concept employing in-cylinder gasoline and natural gas

The present paper represents a small piece of an extensive experimental effort investigating the dual-fuel operation of a light-duty spark ignited engine. Natural gas (NG) was directly injected into the cylinder and gasoline was injected into the intake-port. Direct injection (DI) of NG was used in order to overcome the power density loss usually experienced with NG port-fuel injection (PFI) as it allows an injection after intake valve closing. Having two separate fuel systems allows for a continuum of in-cylinder blend levels from pure gasoline to pure NG operation. The huge benefit of gasoline is its availability and energy density, whereas NG allows efficient operation at high load due to improved combustion phasing enabled by its higher knock resistance. Furthermore, using NG allowed a reduction of carbon dioxide emissions across the entire engine map due to the higher hydrogen-to-carbon ratio. Exhaust gas recirculation (EGR) was used to (a) increase efficiency at low and part-load operation and (b) reduce the propensity of knock at higher compression ratios (CRs) thereby enabling blend levels with greater amount of gasoline across a wider operating range. Two integral engine parameters, CR and in cylinder turbulence levels, were varied in order to study their influence on efficiency, emissions, and performance over a specific speed and load range. Increasing the CR from 10.5 to 14.5 allowed an absolute increase in indicated thermal efficiency of snore than 3% for 7.5% NG (2.5% gasoline) operation at 8 bar net indicated mean effective pressure (IMEP) and 2500 rpm. However, as anticipated, the achievable peak load at CR 14.5 with 100% gasoline was greatly reduced due to its lower knock resistance. The in cylinder turbulence level was varied by means of tumble plates (TPs) as well as an insert for the NG injector that guides the injection "spray" to augment the tumble motion. The usage of TPs showed a significant increase in EGR dilution tolerance for pure gasoline operation, however, no such impact was found for blended operation of gasoline and NG.

Sevik, James↗
DOE OSTI2018

EFFECTS OF PORT FUEL AND DIRECT INJECTION STRATEGIES AND INTAKE CONDITIONS ON GASOLINE COMPRESSION IGNITION OPERATION

GGasoline compression ignition (GCI) using a single gasoline-type fuel for port fuel and direct injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation (EGR)) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of EGR appears more practical. Furthermore, for high temperature GCI, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high temperature GCI combustion using EEE gasoline. Engine testing was conducted at an engine speed of 1038 rpm and brake mean effective pressure (BMEP) of 14 bar. Port fuel and direct injection strategies were utilized to increase the premixed combustion fraction. The impact on engine performance and emissions with respect to varying the injection and intake operating parameters was quantified within this study. A combined effect of reducing heat transfer and increasing exhaust loss resulted in a flat trend of brake thermal efficiency (BTE) when retarding direct injection timing, while increased port fuel mass improved BTE due to advanced combustion phasing and reduced heat transfer loss. Overall, varying intake valve close timing, EGR, intake pressure and temperature with the current pressure rise rate and soot emissions constraint was not effective in improving BTE, as the benefit of low heat transfer loss was always offset by increased exhaust loss.

Wang, Buyu↗
DOE OSTI2018

Impact of Injection Strategies on Combustion Characteristics, Efficiency and Emissions of Gasoline Compression Ignition Operation in a Heavy-duty Multi-cylinder Engine

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NO(x)and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Additionally, engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. Furthermore, the impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

42 ENGINEERING↗
DOE OSTI2017

Instantaneous and cycle optimization of fuel usage on a dual fuel vehicle leveraging gasoline and natural gas

Recent increases in natural gas supply have led to a desire to leverage this fuel in the transportation sector. Dual fuel engines provide a platform on which to use natural gas efficiently; these engines, however, require new hardware and new control strategies to properly utilize two fuels simultaneously. This paper explores the impact of implementing dual fuel capabilities on a sedan and demonstrates that a dual fuel E10 and compressed natural gas engine is able to improve the average engine efficiency by up to 6.5% compared to a single fuel engine on standard drive cycles. An optimal control technique is also developed, and the proposed approach allows factors including fuel cost and fuel availability to be taken into account. Optimization at each time instant is investigated and contrasted with optimization over the entire cycle. Cycle optimization is shown to have particular value for cases in which the level in one fuel tank is low.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2017

Optimal Energy Control of a Dual Fuel Vehicle Fuelled by Natural Gas and E10

Due to the increasing availability of natural gas, there is growing interest in using this fuel for transportation. Utilizing natural gas along with gasoline can provide a way to leverage the high knock resistance of natural gas while avoiding some of the ignitability challenges of this fuel. This paper leverages experimental data for a single cylinder engine to model power production on a mid-size sedan. Using this model, an optimal energy management strategy is explored. Several weighting strategies are considered including techniques which consider fuel availability, fuel cost, and carbon emissions. The effectiveness of these methods are considered over the UDDS, HWY, and US06 cycles. While there is little benefit to such a fuel blending algorithm at low loads, at high loads (such as those encountered in the US06 cycle) blending can provide up to a 7% improvement in efficiency.

Control and diagnosis of automotive systems↗
DOE OSTI2017

Effects of Fuel Laminar Flame Speed Compared to Engine Tumble Ratio, Ignition Energy, and Injection Strategy on Lean and EGR Dilute Spark Ignition Combustion

Previously we show that fuels with higher laminar flame speed also have increased tolerance to EGR dilution. In this work, the effects of fuel laminar flame speed on both lean and EGR dilute spark ignition combustion stability were examined. Fuels blends of pure components (iso-octane, n-heptane, toluene, ethanol, and methanol) were derived at two levels of laminar flame speed. Each fuel blend was tested in a single-cylinder spark-ignition engine under both lean-out and EGR dilution sweeps until the coefficient of variance of indicated mean effective pressure increased above thresholds of 3% and 5%. The relative importance of fuel laminar flame speed to changes to engine design parameters (spark ignition energy, tumble ratio, and port vs. direct injection) was also assessed. Our results showed that fuel laminar flame speed can have as big an effect on lean or EGR dilute engine operation as engine design parameters, with the largest effects seen during EGR dilute operation and when changes were made to cylinder charge motion.

10 SYNTHETIC FUELS↗
DOE OSTI2017

Influence of Compression Ratio on High Load Performance and Knock Behavior for Gasoline Port-Fuel Injection, Natural Gas Direct Injection and Blended Operation in a Spark Ignition Engine

Natural Gas (NG) is an alternative fuel which has attracted a lot of attention recently, in particular in the US due to shale gas availability. The higher hydrogen-to-carbon (H/C) ratio, compared to gasoline, allows for decreasing carbon dioxide emissions throughout the entire engine map. Furthermore, the high knock resistance of NG allows increasing the efficiency at high engine loads compared to fuels with lower knock resistance. NG direct injection (DI) allows for fuel to be added after intake valve closing (IVC) resulting in an increase in power density compared to an injection before IVC. Steady-state engine tests were performed on a single-cylinder research engine equipped with gasoline (E10) port-fuel injection (PFI) and NG DI to allow for in-cylinder blending of both fuels. Knock investigations were performed at two discrete compression ratios (CR), 10.5 and 12.5. Operating conditions span mid-load, wide-open-throttle and boosted conditions, depending on the knock response of the fuel blend. Blended operation was performed using E10 gasoline and NG. An additional gasoline type fuel (E85) with higher knock resistance than E10 was used as a high-octane reference fuel, since the octane rating of E10-NG fuel blends is unknown. Spark timing was varied at different loads under stoichiometric conditions in order to study the knock response as well as the effects on performance and efficiency. As anticipated, results suggest that the knock resistance can be increased significantly by increasing the NG amount. Comparing the engine operation with the least knock resistant fuel, E10 PFI, and the fuel blend with the highest knock resistance, 75% NG DI, shows an increase in indicated mean effective pressure of about 9 bar at CR 12.5. The usage of reference fuels with known knock characteristics allowed an assessment of knock characteristic of intermediate E10-NG blend levels. Mathematical correlations were developed allowing characterizing the occurrence of knocking combustion by using the Livengood-Wu knock integral. For most of the fueling strategies and operating conditions, the mathematical correlations show good agreement when compared to experimental data.

combustion↗