Engineering topics
Pan, Mingao
Publications and source records attributed to Pan, Mingao.
A Chlorinated Donor Polymer Achieving High‐Performance Organic Solar Cells with a Wide Range of Polymer Molecular Weight
Abstract In the field of non‐fullerene organic solar cells (OSCs), compared to the rapid development of non‐fullerene acceptors, the progress of high‐performance donor polymers is relatively slow. The property and performance of donor polymers in OSCs are often sensitive to the molecular weight of the polymers. In this study, a chlorinated donor polymer named D18‐Cl is reported, which can achieve high performance with a wide range of polymer molecular weight. The devices based on D18‐Cl show a higher open‐circuit voltage ( V OC ) due to the slightly deeper energy levels and an outstanding short‐circuit current density ( J SC ) owing to the appropriate long periods of blend films and less ([6,6]‐phenyl‐C71‐butyric acid methyl ester) (PC 71 BM) in mixed domains, leading to the higher efficiency of 17.97% than those of the D18‐based devices (17.21%). Meanwhile, D18‐Cl can achieve high efficiencies (17.30–17.97%) when its number‐averaged molecular weight ( M n ) is ranged from 45 to 72 kDa. In contrast, the D18‐based devices only exhibit relatively high efficiencies in a narrow M n range of ≈70 kDa. Such property and performance make D18‐Cl a promising donor polymer for scale‐up and low‐cost production.
A Difluoro‐Monobromo End Group Enables High‐Performance Polymer Acceptor and Efficient All‐Polymer Solar Cells Processable with Green Solvent under Ambient Condition
Abstract In this paper, a difluoro‐monobromo end group is designed and synthesized, which is then used to construct a novel polymer acceptor (named PY2F‐T) yielding high‐performance all‐polymer solar cells with 15.22% efficiency. The fluorination strategy can increase the intramolecular charge transfer and interchain packing of the previous PY‐T based acceptor, and significantly improve photon harvesting and charge mobility of the resulting polymer acceptor. In addition, detailed morphology investigations reveal that the PY2F‐T‐based blend shows smaller domain spacing and higher domain purity, which significantly suppress charge recombination as supported by time‐resolved techniques. These polymer properties enable simultaneously enhanced J SC and FF of the PY2F‐T‐based devices, eventually delivering device efficiencies of over 15%, significantly outperforming that of the devices based on the non‐fluorinated PY‐T polymer (13%). More importantly, the PY2F‐T‐based active layers can be processed under ambient conditions and still achieve a 14.37% efficiency. They can also be processed using non‐halogenated solvent o ‐xylene (no additive) and yield a decent performance of 13.05%. This work demonstrates the success of the fluorination strategy in the design of high‐performance polymer acceptors, which provide guidelines for developing new all‐PSCs with better efficiencies and stabilities for commercial applications.
Regio‐Regular Polymer Acceptors Enabled by Determined Fluorination on End Groups for All‐Polymer Solar Cells with 15.2 % Efficiency
Abstract Polymerization sites of small molecule acceptors (SMAs) play vital roles in determining device performance of all‐polymer solar cells (all‐PSCs). Different from our recent work about fluoro‐ and bromo‐ co‐modified end group of IC‐FBr (a mixture of IC‐FBr1 and IC‐FBr2), in this paper, we synthesized and purified two regiospecific fluoro‐ and bromo‐ substituted end groups (IC‐FBr‐ o & IC‐FBr‐ m ), which were then employed to construct two regio‐regular polymer acceptors named PYF‐T‐ o and PYF‐T‐ m , respectively . In comparison with its isomeric counterparts named PYF‐T‐ m with different conjugated coupling sites, PYF‐T‐ o exhibits stronger and bathochromic absorption to achieve better photon harvesting. Meanwhile, PYF‐T‐ o adopts more ordered inter‐chain packing and suitable phase separation after blending with the donor polymer PM6, which resulted in suppressed charge recombination and efficient charge transport. Strikingly, we observed a dramatic performance difference between the two isomeric polymer acceptors PYF‐T‐ o and PYF‐T‐ m . While devices based on PM6:PYF‐T‐ o can yield power conversion efficiency (PCE) of 15.2 %, devices based on PM6:PYF‐T‐ m only show poor efficiencies of 1.4 %. This work demonstrates the success of configuration‐unique fluorinated end groups in designing high‐performance regular polymer acceptors, which provides guidelines towards developing all‐PSCs with better efficiencies.
Regio‐Regular Polymer Acceptors Enabled by Determined Fluorination on End Groups for All‐Polymer Solar Cells with 15.2 % Efficiency
Abstract Polymerization sites of small molecule acceptors (SMAs) play vital roles in determining device performance of all‐polymer solar cells (all‐PSCs). Different from our recent work about fluoro‐ and bromo‐ co‐modified end group of IC‐FBr (a mixture of IC‐FBr1 and IC‐FBr2), in this paper, we synthesized and purified two regiospecific fluoro‐ and bromo‐ substituted end groups (IC‐FBr‐ o & IC‐FBr‐ m ), which were then employed to construct two regio‐regular polymer acceptors named PYF‐T‐ o and PYF‐T‐ m , respectively . In comparison with its isomeric counterparts named PYF‐T‐ m with different conjugated coupling sites, PYF‐T‐ o exhibits stronger and bathochromic absorption to achieve better photon harvesting. Meanwhile, PYF‐T‐ o adopts more ordered inter‐chain packing and suitable phase separation after blending with the donor polymer PM6, which resulted in suppressed charge recombination and efficient charge transport. Strikingly, we observed a dramatic performance difference between the two isomeric polymer acceptors PYF‐T‐ o and PYF‐T‐ m . While devices based on PM6:PYF‐T‐ o can yield power conversion efficiency (PCE) of 15.2 %, devices based on PM6:PYF‐T‐ m only show poor efficiencies of 1.4 %. This work demonstrates the success of configuration‐unique fluorinated end groups in designing high‐performance regular polymer acceptors, which provides guidelines towards developing all‐PSCs with better efficiencies.
Random Polymerization Strategy Leads to a Family of Donor Polymers Enabling Well‐Controlled Morphology and Multiple Cases of High‐Performance Organic Solar Cells
Abstract Developing high‐performance donor polymers is important for nonfullerene organic solar cells (NF‐OSCs), as state‐of‐the‐art nonfullerene acceptors can only perform well if they are coupled with a matching donor with suitable energy levels. However, there are very limited choices of donor polymers for NF‐OSCs, and the most commonly used ones are polymers named PM6 and PM7, which suffer from several problems. First, the performance of these polymers (particularly PM7) relies on precise control of their molecular weights. Also, their optimal morphology is extremely sensitive to any structural modification. In this work, a family of donor polymers is developed based on a random polymerization strategy. These polymers can achieve well‐controlled morphology and high‐performance with a variety of chemical structures and molecular weights. The polymer donors are D–A1–D–A2‐type random copolymers in which the D and A1 units are monomers originating from PM6 or PM7, while the A2 unit comprises an electron‐deficient core flanked by two thiophene rings with branched alkyl chains. Consequently, multiple cases of highly efficient NF‐OSCs are achieved with efficiencies between 16.0% and 17.1%. As the electron‐deficient cores can be changed to many other structural units, the strategy can easily expand the choices of high‐performance donor polymers for NF‐OSCs.