Search NASA⌕ Search

Engineering topics

Papadopoulos, P.

Publications and source records attributed to Papadopoulos, P..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

The Exo-Brake as an Inexpensive Means of Achieving Sample Return from Low Earth Orbit – Recent Flight

The Exo-Brake is a simple, non-propulsive means of deorbiting small pay-loads from orbital platforms such as the Inter-national Space Station (ISS). Recent flight experiments involving the TechEdSat (TES) 6, 7, 8 are discussed in terms of both ‘targeted’ and ‘disposal’ de-orbit techniques. These build on the previous flight experiments with fixed surface areas – and now involve improved uplink/downlink communication and GPS for improved targeting and control. The recent targeting experiments are dis-cussed involving the TechEdSat-6,7,8 nanosatellites. The extension of the concept to a 1-stage, 3-stage, and lifting entry sample re-turn system are discussed.

Murbach, Marcus S.↗
NASA NTRS2018

The TechEdSat-N Series: A Collaborative Technology Development Platform in the Nano-Satellite Form Factor

The TechEdSat-1 (TES-1) was the first U.S. CubeSat to be deployed from the ISS (International Space Station). This permitted the initiation of a flight series that has recently de-orbited the 6th nano-satellite with subsequent numbers 7-10 under development. The nano-satellites range from 1U (1 unit) to 6U (TechEdSat-8) but have the critical ISS Safety design features standardized in order to focus on the particular experiment objectives. Incremental experimental development has included unique communication subsystems such as command/control of the nanosatellite through email commands -as well as a recent record for Wifi transmission. Also, the thermophysics of controlled drag devices (Exo-Brake) has been developed which will prelude sample return and planetary exploration applications. The successful "rapid incremental experiment" approach has also been incorporated into collaborations with academia, permitting professors/student interns to be exposed to the rigors of space mission hardware design and execution. The TechEdSat-8, a linear 6U configuration, allows for 5 different groups to contribute an "experiment, sensor, or sub-system" through a well-defined common interface. Lastly, the flying laboratory concept is helpful in developing future interplanetary nano-satellite subsystems which will advance exploration goals by allowing rapid demonstration/validation first in LEO (Low Earth Orbit).

Small Payload Quick Return↗
NASA NTRS2017

TechEdSat-N and ETC Series

This presentation address the issues and how to involve students in the process of develping, building and certifying flight hardware for ISS and development of Mars missions.

Murbach, M.↗
NASA NTRS2016

Modeling the Exo-Brake and the Development of Strategies for De-Orbit Drag Modulation

The Exo-Brake is a simple, non-propulsive means of de-orbiting small payloads from orbital platforms such as the International Space Station (ISS). Two de-orbiting experiments with fixed surface area Exo-Brakes have been successfully conducted in the last two years on the TechEdSat-3 and -4 nano-satellite missions. The development of the free molecular flow aerodynamic data-base is presented in terms of angle of attack, projected front surface area variation, and altitude. Altitudes are considered ranging from the 400km ISS jettison altitude to 90km. Trajectory tools are then used to predict de-orbit/entry corridors with the inclusion of the key atmospheric and geomagnetic uncertainties. Control system strategies are discussed which will be applied to the next two planned TechEdSat-5 and -6 nano-satellite missions - thus increasing the targeting accuracy at the Von Karman altitude through the proposed drag modulation technique.

Exo-Brake↗
NASA NTRS1995

Estimates of Heat Shielding Requirements for Saturn Probe Missions

Entry trajectories, decelerations, heating and heat shielding requirements of probes entering the atmosphere of Saturn at relative entry velocities ranging from 26.5 - 33.0 km/sec were studied. Much of the Galileo Jupiter probe technology was applicable to these outer planet probes; therefore, the same configuration was used. A wide range entry flight path angles were used in the trajectory analysis in order to satisfy the complete range of arrival conditions and trajectory requirements. Various entry probe sizes and a range of entry masses from 32 - 258 kg were considered. The carbon phenolic heat shield material used on the Galileo and the successful Pioneer-Venus probes was selected. Turbulent boundary layer convection dominated the heating of the Saturn probes; radiative heating was negligible by comparison at the entry velocities considered. The peak heating rates were found to be about 4 kW per square centimeter, or approximately 17% of the Galileo probe's expected maximum value. The forebody heat shield mass fractions for the Saturn probes were found to vary from about 0.18 to 0.28. By comparison, the Pioneer-Venus probes' heat shield mass fractions ranged from 0.10 to 0.13 and the Galileo probe's forebody value is 0.43.

Wercinski, P.↗
NASA NTRS1995

The NASA Ames 16-Inch Shock Tunnel Nozzle Simulations and Experimental Comparison

The 16-Inch Shock Tunnel at NASA Ames Research Center is a unique test facility used for hypersonic propulsion testing. To provide information necessary to understand the hypersonic testing of the combustor model, computational simulations of the facility nozzle were performed and results are compared with available experimental data, namely static pressure along the nozzle walls and pitot pressure at the exit of the nozzle section. Both quasi-one-dimensional and axisymmetric approaches were used to study the numerous modeling issues involved. The facility nozzle flow was examined for three hypersonic test conditions, and the computational results are presented in detail. The effects of variations in reservoir conditions, boundary layer growth, and parameters of numerical modeling are explored.

TokarcikPolsky, S.↗
NASA NTRS1992

MESUR probe aerobrake preliminary design study

Aerobrake design for the Mars Environmental Survey (MESUR) vehicles is considered which is intended for both a nominal entry velocity of 7 km/sec and a high-speed case of 9 km/sec. Topics discussed include the entry environment, the thermal protection requirements for several types of heat shield materials, the structural design of the aeroshell, and the total aerobrake masses and mass fractions. For the nominal 7 km/sec entry, a silicone elastometric charring ablator, SLA-561, was found to be the lightest heat shield material. For the 7 km/sec entry, the mass fraction of the aerobrake was 13.2 percent. For the 9 km/sec entry, the heat shield consisted of the medium-density ablator AVCOAT-5026; SLA-561 was used on part of the conical skirt. The aerobrake mass fraction in this case was 18 percent. It is recommended that separate aerobrakes be designed for probes entering at 7 and 9 km/sec.

Tauber, M.↗