Search NASA⌕ Search

Engineering topics

Paquette, Beth

Publications and source records attributed to Paquette, Beth.

Additive Manufacturing Circuitry on Rigid and Flexible Substrates for Space Applications

Additive manufacturing techniques for electronics, including Aerosol Jet Printing (AJP), Syringe Printing, and Ink Jet Printing, will enable new detector assemblies that were not previously possible with traditional assembly processes. This technology has the potential to reduce mass and volume for fabrication and assembly of detector, instrument and electronics concepts by reducing trace widths down to 10 microns, printing on complex geometries, and allowing new concept production. This presentation summarizes efforts developing printing techniques to manufacture detectors and circuitry for space applications.

Detectors↗

Optical Communications Feasibility Study for Science Mission Located at Sun-Earth Lagrange Point L2

NASA's Exploration and Space Communications projects division recently completed an investigative study, researching the feasibility of integrating optical communications capabilities onto a science-based mission orbiting at Lagrange Point 2 (L2). Optical communications has been demonstrated and integrated into many low-Earth-orbiting missions, however, using the technology as far as L2 needed to be thoroughly researched and proven similarly as efficient as the mission's planned radio frequency (RF) system, but preferably more efficient that the equivalent RF systems. The investigation team was charged with assessing the feasibility of including optical communications on the mission without interfering with its primary science objectives. This came to be known as the "Do No Harm" approach to accommodation. As science and detection technologies become more advanced, data rates and communications requirements continue to evolve. Missions with complex science instruments have a need for more optimized communications capabilities. Optical communications technologies provide NASA and industry missions with increased data rates and quicker response times, allowing scientists to access more data than ever before. Missions utilizing optical communications will have a lighter and more efficient method of transmitting data to users on Earth. The team investigating this opportunity discovered that including an optical communications payload on board the mission to provide a bi-directional link between the spacecraft and Earth-based ground stations is feasible and reaches data rates that are comparable to, and even exceed, the mission's RF system. In the course of their investigation, the team also discovered significant navigation and ranging benefits provided by the optical communications payload (OCP).

LCRD↗

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Aerosol Jet Printing (AJP) and other additive electronics technologies will enable new detector assemblies that were not previously possible with traditional assembly processes. This technology has the potential to reduce mass and volume for fabrication and assembly of detector, instrument and electronics concepts by reducing trace widths down to 10 microns, printing on complex geometries, and allowing new concept production. This poster summarizes development efforts of printed interconnects for space applications.

Printed Hybrid Electronics↗

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Direct-write printing techniques will enable new detector assemblies that were not previously possible with traditional assembly processes. Detector concepts were manufactured using this technology to validate repeatability. Additional detector applications and printed wires on a 3-dimensional magnetometer bobbin will be designed for print. This effort focuses on evaluating performance for direct-write manufacturing techniques on 3-dimensional surfaces. Direct-write manufacturing has the potential to reduce mass and volume for fabrication and assembly of advanced detector concepts by reducing trace widths down to 10 microns, printing on complex geometries, allowing new electronic concept production, and reduced production times of complex those electronics.

Direct-write printing↗

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Direct-write printing techniques will enable new detector assemblies that were not previously possible with traditional assembly processes. Detector concepts were manufactured using this technology to validate repeatability. Additional detector applications and printed wires on a 3-dimensional magnetometer bobbin will be designed for print. This effort focuses on evaluating performance for direct-write manufacturing techniques on 3-dimensional surfaces. Direct-write manufacturing has the potential to reduce mass and volume for fabrication and assembly of advanced detector concepts by reducing trace widths down to 10 microns, printing on complex geometries, allowing new electronic concept production, and reduced production times of complex those electronics.

Additive Manufacturing↗

Direct Write Printing on Thin and Flexible Substrates for Space Applications

This presentation describes the work done on direct-write printing conductive traces for a flexible detector application. A Repeatability Plan was established to define detector requirements, material and printer selections, printing facilities, and tests to verify requirements are met. Designs were created for the detector, and printed using an aerosol jet printer. Testing for requirement verification is ongoing.

flexible↗