Search NASA⌕ Search

Engineering topics

Paranthaman, Mariappan Parans

Publications and source records attributed to Paranthaman, Mariappan Parans.

At least 91 records · Page 5

Hetero-junction photovoltaic device and method of fabricating the device

A hetero-junction device and fabrication method in which phase-separated n-type and p-type semiconductor pillars define vertically-oriented p-n junctions extending above a substrate. Semiconductor materials are selected for the p-type and n-type pillars that are thermodynamically stable and substantially insoluble in one another. An epitaxial deposition process is employed to form the pillars on a nucleation layer and the mutual insolubility drives phase separation of the materials. During the epitaxial deposition process, the orientation is such that the nucleation layer initiates propagation of vertical columns resulting in a substantially ordered, three-dimensional structure throughout the deposited material. An oxidation state of at least a portion of one of the p-type or the n-type semiconductor materials is altered relative to the other, such that the band-gap energy of the semiconductor materials differ with respect to stoichiometric compositions and the device preferentially absorbs particular selected bands of radiation.

42 ENGINEERING↗

Tailored Recovery of Carbons from Waste Tires for Enhanced Performance as Anodes in Lithium-ion Batteries

Morphologically tailored pyrolysis-recovered carbon black is utilized in lithium-ion batteries as a potential solution for adding value to waste tire-rubber-derived materials. Micronized tire rubber was digested in a hot oleum bath to yield a sulfonated rubber slurry that was then filtered, washed, and compressed into a solid cake. Carbon was recovered from the modified rubber cake by pyrolysis in a nitrogen atmosphere. The chemical pretreatment of rubber produced a carbon monolith with higher yield than that from the control (a fluffy tire-rubber-derived carbon black). The carbon monolith showed a very small volume fraction of pores of widths 3 4 nm, reduced specific surface area, and an ordered assembly of graphitic domains. Electrochemical studies on the recovered-carbon-based anode revealed an improved Li-ion battery performance with higher reversible capacity than that of commercial carbon materials. Anodes made with a sulfonated tire-rubber-derived carbon and a control tire-rubber-derived carbon, respectively, exhibited an initial coulombic efficiency of 80% and 45%, respectively. The reversible capacity of the cell with the sulfonated carbon as anode was 400 mAh/g after 100 cycles, with nearly 100% coulombic efficiency. Our success in producing higher performance carbon material from waste tire rubber for potential use in energy storage applications adds a new avenue to tire rubber recycling.

Naskar, Amit K↗

Chemical Solution Derived Planarization Layers for Highly Aligned IBAD MgO Templates

The main goal of this research is to develop a chemical solution derived planarization layer to fabricate highly aligned IBAD-MgO templates for the development of high temperature superconductor (HTS) based coated conductors. The standard IBAD-MgO template needs an additional electrochemical polishing step of the mechanically polished 50- m-thick Hastelloy C-276 substrates to ensure a flat and smooth surface for subsequent growth of multi-layer buffer architectures, which include: sputtered 80-nm Al2O3; sputtered 7-nm Y2O3; IBAD 10-nm MgO; sputtered 30-nm homo-epi MgO; and sputtered 30-nm LaMnO3 (LMO) layers. We have successfully developed a solution planarization layer that removes the electrochemical polishing step and also acts as a barrier layer. Crack-free, smooth Al2O3 layers were prepared on mechanically polished Hastelloy substrates using a chemical solution process. A nearly 10-15-nm thick Al2O3 layer was formed with each coating and the coating was repeated several times to achieve the desired film thickness with intermediate heat-treatments after each coating. The Al2O3 planarization layer significantly reduced the surface roughness of the substrate. The average surface roughness value, Ra for a starting substrate was 9-10 nm. After 8 coatings of Al2O3 layer, the Ra was reduced to 2 nm. Highly aligned IBAD-MgO layers with out-of-plane and in-plane textures comparable to the standard IBAD-MgO layers were successfully deposited on top of the solution planarization Al2O3 layers with an Y2O3 nucleation layer using a reel-to-reel ion-beam sputtering system. Both homo-epi MgO and LMO layers were subsequently deposited on the IBAD-MgO layers using rf sputtering to complete the buffer stack required for the growth of HTS films. YBa2Cu3O7- (YBCO) films with a thickness of 0.8 m deposited on these IBAD-MgO templates by pulsed laser deposition showed a high self-field critical current density, Jc of 3.04 MA/cm2 at 77 K and 6.05 MA/cm2 at 65 K. These results demonstrate that a low-cost chemical-solution-based, high-throughput Al2O3 planarization layer can remove the electro-polishing step and replace sputtered Al2O3 layers for the production of high Jc YBCO-coated conductors.

Paranthaman, Mariappan Parans↗

Neutron diffraction and electrochemical studies of Na0.79(Co,Mn)O2 cathodes for sodium-ion batteries

Na0.79CoO2 and Na0.79Co0.7Mn0.3O2 with a layered hexagonal structure (P2-type) were synthesized by the Pechini process followed by heat treatment at elevated temperatures in order to achieve the crystalline phases. The samples were characterized with x-ray diffraction, neutron diffraction, magnetic measurements and electrochemical charge-discharge cycling. X-ray diffraction confirmed the P2 layered hexagonal structure after heat treatment at 900 C in air. Neutron diffraction patterns confirm Mn doping on Co sites without forming pronounced Mn-Co ordering. Cyclic voltammetry showed the oxidation and reduction peaks of Co and Mn, indicating the intercalation and de-intercalation behavior of the Na ions. A discharge capacity of 60 mAh/g was achieved for both the compositions, with the Na0.79Co0.70Mn0.3O2 composition showing a more stable discharge capacity up to 60 cycles.

Beck, Faith R↗

Cr, N-Codoped TiO2 Mesoporous Microspheres for Li-ion Rechargeable Batteries with Enhanced Electrochemical Performance

Cr,N-codoped TiO2 mesoporous microspheres synthesized using hydrothermal and subsequent nitridation treatment, exhibited higher solubility of nitrogen, and improved electrical conductivity than N-doped TiO2, as anode for Lithium-ion rechargeable batteries, which led to improving charge-discharge capacity at 0.1 C and twice higher rate capability compared to that of nitrogen-doped TiO2 mesoporous microsphere at 10 C

Bi, Zhonghe↗

Synthesis and Characterization of Lithium Bis(fluoromalonato)borate (LiBFMB) for Lithium Ion Battery Applications

A new orthochelated salt, lithium bis(monofluoromalonato)borate (LiBFMB), has been synthesized and purified for the first time for application in lithium ion batteries. The presence of fluorine in the borate anion of LiBFMB increases its oxidation potential and also facilitates ion dissociation, as reflected by the ratio of ionic conductivity measured by electrochemical impedance spectroscopy ( exp) and that by ion diffusivity coefficients obtained using pulsed field gradient nuclear magnetic resonance (PFG-NMR) technique ( NMR). Half-cell tests using 5.0 V lithium nickel manganese oxide (LiNi0.5Mn1.5O4) as a cathode and EC/DMC/DEC as a solvent reveals that the impedance of the LiBFMB cell is much larger than those of LiPF6 and LiBOB based cells, which results in lower capacity and poor cycling performance of the former. XPS spectra of the cycled cathode electrode suggest that because of the stability of the LiBFMB salt, the solid electrolyte interphase (SEI) formed on the cathode surface is significantly different from those of LiPF6 and LiBOB based electrolytes, resulting in more solvent decomposition and thicker SEI layer. Initial results also indicate that using high dielectric constant solvent PC alters the surface chemistry, reduces the interfacial impedance, and enhances the performance of LiBFMB based 5.0V cell.

Liao, Chen↗

Radiation Resistance of XLPE Nano-dielectrics for Advanced Reactor Applications

Recently there has been renewed interest in nuclear reactor safety, particularly as commercial reactors are approaching 40 years service and lifetime extensions are considered, as well as for new reactor building projects around the world. The materials that are currently used in cabling for instrumentation, reactor control, and communications include cross-linked polyethylene (XLPE), ethylene propylene rubber (EPR), polyvinyl chloride (PVC), neoprene, and chlorosulfonated polyethylene. While these materials show suitable radiation tolerance in laboratory tests, failures before their useful lifetime occur due to the combined environmental effects of radiation, temperature and moisture, or operation under abnormal conditions. In addition, the extended use of commercial reactors beyond their original service life places a greater demand on insulating materials to perform beyond their current ratings in these nuclear environments. Nanocomposite materials that are based on XLPE and other epoxy resins incorporating TiO2, MgO, SiO2, and Al2O3 nanoparticles are being fabricated using a novel in-situ method established at ORNL to demonstrate materials with increased resistance to radiation. As novel nanocomposite dielectric materials are developed, characterization of the non-irradiated and irradiated nanodielectrics will lead to a knowledge base that allow for dielectric materials to be engineered with specific nanoparticle additions for maximum benefit to wide-variety of radiation environments found in nuclear reactors. This paper presents the initial findings on the development of XLPE-based SiO2 nano-composite dielectrics in the context of electrical performance and radiation degradation.

dielectrics↗

Defect chemistry of phospho-olivine nanoparticles synthesized by a microwave-assisted solvothermal process

Nanocrystalline LiFePO{sub 4} powders synthesized by a microwave-assisted solvothermal (MW-ST) process have been structurally characterized with a combination of high resolution powder neutron diffraction, synchrotron X-ray diffraction, and aberration-corrected HAADF STEM imaging. A significant level of defects has been found in the samples prepared at 255 and 275 °C. These temperatures are significantly higher than what has previously been suggested to be the maximum temperature for defect formation in LiFePO{sub 4}, so the presence of defects is likely related to the rapid MW-ST synthesis involving a short reaction time (∼5 min). A defect model has been tentatively proposed, though it has been shown that powder diffraction data alone cannot conclusively determine the precise defect distribution in LiFePO{sub 4} samples. The model is consistent with other literature reports on nanopowders synthesized at low temperatures, in which the unit cell volume is significantly reduced relative to defect-free, micron-sized LiFePO{sub 4} powders. - Graphical abstract: Temperature-dependent antisite defect formation has been observed in nanocrystalline LiFePO{sub 4} powders synthesized by a microwave solvothermal process, using high resolution diffraction and STEM imaging. Display Omitted - Highlights: • LiFePO{sub 4} nanopowders synthesized by a microwave-assisted solvothermal process. • Defects directly observed by aberration-corrected HAADF STEM imaging. • Antisite defects present from synthesis at 255 and 275 °C. • Defects present from higher temperature synthesis than previously reported. • Powder diffraction data have been analyzed in detail for various defect models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Method for producing microstructured templates and their use in providing pinning enhancements in superconducting films deposited thereon

The present invention relates to a method for producing a phase-separated layer useful as a flux pinning substrate for a superconducting film, wherein the method includes subjecting at least a first and a second target material to a sputtering deposition technique in order that a phase-separated layer is deposited epitaxially on a primary substrate containing an ordered surface layer. The invention is also directed to a method for producing a superconducting tape containing pinning defects therein by depositing a superconducting film on a phase-separated layer produced by the method described above.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanostructured columnar heterostructures of TiO{sub 2} and Cu{sub 2}O enabled by a thin-film self-assembly approach: Potential for photovoltaics

Graphical abstract: Display Omitted Highlights: ► Material self-assembly in phase-separated oxides is exploited. ► Three-dimensionally nanostructured epitaxial films are grown using sputtering. ► Films are composed of well-ordered oriented nanopillars of n-type TiO{sub 2} and p-type Cu{sub 2}O. ► Observed interfaces at adjacent TiO{sub 2}–Cu{sub 2}O columns are nearly atomically distinct. ► Absorption profile of the composite film captures a wide range of the solar spectrum. -- Abstract: Significant efforts are being devoted to the development of multifunctional thin-film heterostructures and nanostructured material architectures for components with novel applications of superconductivity, multiferroicity, solar photocatalysis and energy conversion. In particular, nanostructured assemblies with well-defined geometrical shapes have emerged as possible high efficiency and economically viable alternatives to planar photovoltaic thin-film architectures. By exploiting phase-separated self-assembly, here we present advances in a vertically oriented two-component system that offers potential for future development of nanostructured thin film solar cells. Through a single-step deposition by magnetron sputtering, we demonstrate growth of an epitaxial, composite film matrix formed as self-assembled, well ordered, phase segregated, and oriented nanopillars of n-type TiO{sub 2} and p-type Cu{sub 2}O. The composite films were structurally characterized to atomic resolution by a variety of analytical tools, and evaluated for preliminary optical properties using absorption measurements. We find nearly atomically distinct TiO{sub 2}–Cu{sub 2}O interfaces (i.e., needed for possible active p–n junctions), and an absorption profile that captures a wide range of the solar spectrum extending from ultraviolet to visible wavelengths. This high-quality materials system could lead to photovoltaic devices that can be optimized for both incident light absorption and carrier collection.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Mesoporous TiO2 spheres with a nitridated conducting layer

Nitridated TiO2 mesoporous spheres have been synthesized by hydrothermal processing followed by post-nitridation with NH3. Characterization data reveal a nitridated conducting layer, in addition to a mesoporous, and nanosized building-block morphology resulting in a large surface area. The samples have an average pore size and surface area of, respectively, 10 nm and 87 m2/g. The nitridated TiO2 mesoporous spheres exhibit a high capacity of > 200 mAh/g with good cyclability and high rate capability, as the nitridated conducting layer and favorable morphology of nanosized spheres provides good electrical contact, accommodates cycling induced strain smoothly, and facilitates lithium-ion diffusion.

anode↗

Self-Organized Amorphous TiO2 Nanotube Arrays on Porous Ti Foam for Rechargeable Lithium and Sodium Ion Batteries

Self-organized amorphous TiO2 nanotube arrays (NTAs) were successfully fabricated on both Ti foil and porous Ti foam through electrochemical anodization techniques. The starting Ti foams were fabricated using ARCAM s Electron Beam Melting (EBM) technology. The TiO2 NTAs on Ti foam were used as anodes in lithium ion batteries; they exhibited high capacities of 103 Ahcm-2 at 10 Acm-2 and 83 Ahcm-2 at 500 Acm-2, which are two to three times higher than those achieved on the standard Ti foil, which is around 40 Ahcm-2 at 10 Acm-2 and 24 Ahcm-2 at 500 Acm-2, respectively. This improvement is mainly attributed to higher surface area of the Ti foam and higher porosity of the nanotube arrays layer grown on the Ti foam. In addition, a Na-ion half-cell composed of these NTAs anodes and Na metal showed a self-improving specific capacity upon cycling at 10 Acm-2. These results indicate that TiO2 NTAs grown on Ti porous foam are promising electrodes for Li-ion or Na-ion rechargeable batteries.

Bi, Zhonghe↗

Overcoming phase instability of RBaCo2O5+ (R = Y and Ho) by Sr substitution for application as cathodes in solid oxide fuel cells

Phase instabilities of the RBaCo2O5+ (R = Y and Ho) layered-perovskites and their decompositions into RCoO3 and BaCoO3-z at 800 oC in air were investigated. This will restrict their high temperature applications such as cathodes in solid oxide fuel cell (SOFC). However, appropriate amount of Sr substitution ( 60 % for R = Y and 70 % for R = Ho) for Ba successfully stabilized the R(Ba1-xSrx)Co2O5+ phase at elevated temperatures. This can be explained by decreasing oxygen vacancies at R-O layer, decreasing R-O bonding length, and consequent improvement of structural integrity. In addition, the Sr substitution (x = 0.6 - 1.0) for Ba provided added benefit with respect to the chemical stability against Ce0.8Gd0.2O1.9 (GDC) electrolyte, which is a critical requirement for the cathodes in SOFC. Among the various compositions investigated, the Y(Ba0.3Sr0.7)Co2O5+ + GDC composite cathode delivered the optimum electrochemical performances with a stable phase demonstrating the potential as a cathode in SOFC.

HoBaCo2O5+↗

Temperature Dependence of Aliovalent-vanadium Doping in LiFePO4 Cathodes

Vanadium-doped olivine LiFePO4 cathode materials have been synthesized by a novel low-temperature microwave-assisted solvothermal (MW-ST) method at 300 oC. Based on chemical and powder neutron/X-ray diffraction analysis, the compositions of the synthesized materials were found to be LiFe1-3x/2Vx x/2PO4 (0 x 0.2) with the presence of a small number of lithium vacancies charge-compensated by V4+, not Fe3+, leading to an average oxidation state of ~ 3.2+ for vanadium. Heating the pristine 15 % V-doped sample in inert or reducing atmospheres led to a loss of vanadium from the olivine lattice with the concomitant formation of a Li3V2(PO4)3 impurity phase; after phase segregation, a partially V-doped olivine phase remained. For comparison, V-doped samples were also synthesized by conventional ball milling and heating, but only ~ 10 % V could be accommodated in the olivine lattice in agreement with previous studies. The higher degree of doping realized with the MW-ST samples demonstrates the temperature dependence of the aliovalent-vanadium doping in LiFePO4.

Harrison, Katharine L↗