Search NASA⌕ Search

Engineering topics

Paranthaman, Mariappan Parans

Publications and source records attributed to Paranthaman, Mariappan Parans.

At least 145 records · Page 8

YBCO COATED CONDUCTORS

Since the discovery of high-temperature superconductors (HTS) in 1986, both (Bi,Pb)2Sr2Ca2Cu3O10 (BSCCO or 2223 with a critical temperature, Tc of 110 K) and YBa2Cu3O7- (YBCO or 123 with a Tc of 91 K) have emerged as the leading candidate materials for the first generation (1G) and second generation (2G) high temperature superconductor wires or tapes that will carry high critical current density in liquid nitrogen temperatures [1-7]. The crystal structures and detailed fundamental properties of BSCCO and YBCO superconductors have been reviewed by Matsumoto in a separate chapter in this book. The U.S. Department of Energy s target price for the conductor is close to the current copper wire cost of $10-50/kA-meter, i.e. a meter of copper type conductor carrying 1000 A current costs ~ $ 50 [8]. The long-term goal for the DOE, Office of Electricity, Advanced Conductors and Cables program is to achieve HTS wire in 1000 meters long with current carrying capacity of 1000 A/cm [8]. Robust, high-performance HTS wire will certainly revolutionize the electric power grid and various other electric power equipments as well. Sumitomo Electric Power (Japan) has been widely recognized as the world leader in manufacturing the first-generation HTS wires based on BSCCO materials using the Oxide-Powder-In-Tube (OPIT) over-pressure process [9]. Typically, 1G HTS wires carry critical currents, Ic, of over 200 Amperes (A) in piece lengths of one kilometer lengths at the standard 4 mm width and ~ 200 m thickness. However, due to the higher cost of 1G wire, mainly because of the cost of Ag alloy sheath, the researchers shifted their effort towards the development of YBCO (second generation 2G) tapes in the last fifteen years [1-7]. One of the main obstacles to the ability to carry high critical currents in YBCO films has been the phenomenon of weak links, i.e., grain boundaries formed by the misalignment of neighboring YBCO grains are known to form obstacles to current flow [10]. By carefully aligning the grains in YBCO films, low angle boundaries between superconducting YBCO grains allow more current to flow. In fact below a critical misalignment angle of 4 , the critical current density approaches that of YBCO films grown on single crystal substrates [10]. Typically, 2G HTS wires have three components, flexible metal substrate, buffer layers, and REBa2Cu3O7- (REBCO: RE = Rare Earth) superconductor layers [1-7]. Several methods were developed to obtain biaxially textured templates suitable for fabricating high-performance YBCO coated conductors. They are Ion-Beam Assisted Deposition (IBAD), Rolling-Assisted Biaxially Textured Substrates (RABiTS) and Inclined-Substrate Deposition (ISD). Compared to 1G wire, for producing 2G wires using RABiTS or IBAD process, silver is replaced by a low cost nickel alloy, which allows for fabrication of less expensive HTS wires.

36 MATERIALS SCIENCE↗

Chemical solution deposition method of fabricating highly aligned MgO templates

A superconducting article includes a substrate having an untextured metal surface; an untextured barrier layer of La.sub.2Zr.sub.2O.sub.7 or Gd.sub.2Zr.sub.2O.sub.7 supported by and in contact with the surface of the substrate; a biaxially textured buffer layer supported by the untextured barrier layer; and a biaxially textured superconducting layer supported by the biaxially textured buffer layer. Moreover, a method of forming a buffer layer on a metal substrate includes the steps of: providing a substrate having an untextured metal surface; coating the surface of the substrate with a barrier layer precursor; converting the precursor to an untextured barrier layer; and depositing a biaxially textured buffer layer above and supported by the untextured barrier layer.

36 MATERIALS SCIENCE↗

Synthesis and characterization of anodized titanium-oxide nanotube arrays

Anodized titanium-oxide containing highly ordered, vertically oriented TiO2 nanotube arrays is a nanomaterial architecture that shows promise for diverse applications. In this paper, an anodization synthesis using HF-free aqueous solution is described. The anodized TiO2 film samples (amorphous, anatase, and rutile) on titanium foils were characterized with scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. Additional characterization in terms of photocurrent generated by an anode consisting of a titanium foil coated by TiO2 nanotubes was performed using an electrochemical cell. A platinum cathode was used in the electrochemical cell. Results were analyzed in terms of the efficiency of the current generated, defined as the ratio of the difference between the electrical energy output and the electrical energy input divided by the input radiation energy, with the goal of determining which phase of TiO2 nanotubes leads to more efficient hydrogen production. It was determined that the anatase crystalline structure converts light into current more efficiently and is therefore a better photocatalytic material for hydrogen production via photoelectrochemical splitting of water.

08 HYDROGEN↗

Magnetic order in CaMn2Sb2 studied via powder neutron diffraction.

This paper reports a neutron powder diffraction study of CaMn2Sb2 in the terperature range of 20-300K. Collinear long-range antiferromagnetic order of manganese ions occurs below 85K, where a transition is observed in the dc magnetic susceptibiloity measured with a single crystal.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Magnetic field orientation dependence of flux pinning in (Gd,Y)Ba2Cu3O7-x coated conductor with tilted lattice and nanostructures

The dependence of the critical current density (J{sub c}) on the orientation of an applied magnetic field was studied for a prototype (Gd,Y)Ba{sub 2}Cu{sub 3}O{sub 7?x} (GdYBCO) coated conductor fabricated by MOCVD on an IBAD-MgO template. Additional rare-earth cations (Y and Gd) and Zr were incorporated into the superconducting film to form (Y,Gd){sub 2}O{sub 3} and BaZrO{sub 3} nanoparticles extended nearly parallel to the a-b planes and to the c-axis, respectively, to enhance the flux pinning. In-field measurement of J{sub c} was carried out with electrical current flowing either along or perpendicular to the longitudinal axis of the tape, while a maximum Lorentz force configuration was always maintained. Details in the angular dependence of J{sub c} were related to the unique structure of the film, specifically the tilt in the GdYBCO lattice and the tilts in the extended (Y,Gd){sub 2}O{sub 3} and BaZrO{sub 3} nanoparticles. XRD and TEM were used to study the structure of the coated conductor. The effect of the misalignment between the external field H and the internal field B on the angular dependence of J{sub c} is discussed.

36 MATERIALS SCIENCE↗

Epitaxial Growth of MgO/TiN Multilayers on Cu

The growth of epitaxial MgO/TiN multilayer films on (001) Cu has been investigated. In particular, epitaxial structures were grown on (001) Cu layers that were epitaxial on (001) SrTiO{sub 3}. X-ray diffraction and reflection high-energy electron diffraction indicate that the multilayer structures are epitaxial on the (001) Cu surface. The motivation is the use of crystalline MgO/TiN multilayers as a diffusion barrier to both copper and oxygen. MgO/TiN multilayers are potentially useful as diffusion barriers for Cu interconnects on semiconductors as well as for superconducting wires based on the epitaxial growth of cuprate superconductors on biaxially textured copper.

36 MATERIALS SCIENCE↗

Vapor-Phase Synthesis of Gallium Phosphide Nanowires

Gallium phosphide (GaP) nanowires were synthesized in a high yield by vapor-phase reaction of gallium vapor and phosphorus vapor at 1150 C in a tube furnace system. The nanowires have diameters in the range of 25-100 nm and lengths of up to tens of micrometers. Twinning growth occurs in GaP nanowires, and as a result most nanowires contain a high density of twinning faults. Novel necklacelike GaP nanostructures that were formed by stringing tens of amorphous Ga-P-O microbeads upon one crystalline GaP nanowires were also found in some synthesis runs. This simple vapor-phase approach may be applied to synthesize other important group III-V compound nanowires.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Aligned ZnO Nanorod Arrays Grown Directly on Zinc Foils and Zinc Spheres by a Low-Temperature Oxidation Method.

Vertically aligned, dense ZnO nanorod arrays were grown directly on zinc foils by a catalyst-free, low-temperature (450-500 C) oxidization method. The zinc foils remain conductive even after the growth of ZnO nanorods on its surface. The success of this synthesis largely relies on the level of control over oxygen introduction. By replacing zinc foils with zinc microspheres, unique and sophisticated urchin-like ZnO nanorod assemblies can be readily obtained.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Enhanced flux pinning by BaZrO3 and (Gd,y)2O3 nano-structures in metal organic chemical vapor deposited GdYBCO high temperature superconductor tapes

We have formed BaZrO3 nano-columns and (Gd,Y)2O3 nano-precipitates in reel-to-reel MOCVD processed (Gd,Y)Ba2Cu3O7-x coated conductors and increased the critical currents (Ic) of the conductors in applied magnetic fields to remarkable levels. A (Gd,Y)Ba2Cu3O7-x tape of 1m length with 6.5% Zr-additions and 30% composition rich in both Gd and Y showed Ic values of 813 A/cm-width at (self-field, 77K) and above 186 A/cm-width at (1T, 77K). The strongly enhanced flux pinning over a wide range of magnetic field orientations can be attributed to the bidirectionally aligned defect structures of BaZrO3 and (Gd,Y)2O3 created by optimized MOCVD conditions.

36 MATERIALS SCIENCE↗

Deposition studies and coordinated characterization of MOCVD YBCO films on IBAD-MgO templates.

A recently installed research metal organic chemical vapor deposition (MOCVD) system at Oak Ridge National Laboratory, provided by SuperPower, Inc., has been used to investigate the processing variables of MOCVD YBCO precursors and trends in the resulting properties. Systematic studies of film growth were carried out by optimizing deposition temperature and oxygen flow rate. Structural and superconducting properties of the YBCO films were analyzed by extensive X-ray diffraction, scanning electron microspcopy and transport measurements. The identification of intermediate phase formations after the YBCO precursor transformation was investigated with coordinated reel-to-reel Raman microprobe analysis. With the combination of these characterization techniques, an improved understanding of the growth characteristics of MOCVD YBCO films was established. Finally, critical current densities greater than 2 MA/cm2 for film thicknesses of 0.8 m have been demonstrated.

36 MATERIALS SCIENCE↗

Size control of highly ordered HfO2 nanotube arrays and a possible growth mechanism

Highly ordered HfO{sub 2} nanotube arrays were prepared through an electrochemical anodization in the presence of NH{sub 4}F and ethylene glycol. The voltage-dependent pore size, wall thickness and porosity were studied using scanning electron microscopy and a wall thickness to pore size ratio was proposed on the basis of the results to serve as a boundary condition additional to the 10% porosity rule introduced by the Gosele group. The average distributions of the tube sizes and wall thicknesses of the nanotubes prepared at 20 V were determined from the small-angle x-ray scattering data using a simple polydisperse core-shell cylinder model fit. Temperature-dependent x-ray diffraction measurements show that the as-grown amorphous nanotube arrays can be converted into crystalline nanotube arrays at a temperature above 500 C. Transmission electron microscopy study of the dimple layer under the as-grown nanotube arrays reveals the presence of a layer of ordered HfO{sub 2} nanocrystals. Further microscopic investigation of the nanotube root region indicates that the nanotubes develop from bulbs produced during anodization. A possible gas bubble initiated growth mechanism based on these observations was proposed.

36 MATERIALS SCIENCE↗

Bandgap narrowing of titanium oxide semiconductors by non-compensated anion-cation codoping for enhanced visible-light photoactivity

Titanium dioxide (TiO2) is widely recognized as one of the most promising photocatalysts for solar energy utilization and environmental cleanup, but because of its wide bandgap, pure TiO2 can only absorbs ultraviolet light, which represents 4% of the solar spectrum1-6. Here we establish a conceptually novel approach, termed non-compensated n-p codoping, to narrow the bandgap of TiO2 and shift the optical response into the visible spectral range where a much larger fraction of the solar spectrum can be captured. The concept embodies two key ingredients: The electrostatic attraction within the n-p dopant pair enhances the thermodynamic and kinetic solubility in substitutional doping, and the non-compensated nature ensures the creation of broadened intermediate electronic states that effectively narrow the bandgap. The concept is demonstrated quantitatively within first-principles density functional theory. The experimental evidence for bandgap narrowing is obtained in the forms of direct measurements of the density of states by scanning tunneling spectroscopy, dramatically redshifted and increased optical absorbance, and enhanced photoactivity manifested by efficient hole-electron separation in the visible spectral region. These findings represent the first crucial steps toward development of a new class of titania-based photocatalysts with greatly enhanced efficiency of solar energy conversion facilitating environmentally friendly applications ofrenewable energy.

14 SOLAR ENERGY↗

Strategic Buffer Layer Development for YBCO Coated Conductors

We have developed a simplified buffer layer architecture for the rolling-assisted biaxially textured substrates (RABiTS) template approach. The overall purpose of this research is to enable potentially a low-cost, high throughput and high yield manufacturing processes for buffer fabrication and to gain fundamental understanding of the growth of buffer layers for RABiTS templates. This understanding is critical to the development of a reliable, robust, and long-length manufacturing process for second generation wires. In this study, efforts are being made to either reduce the number of vacuum deposited layers or to replace one or more of these vacuum deposited layers with a solution based layer. We have chosen Gd{sub 2}O{sub 3} - ZrO{sub 2} system as a potential barrier layer for this study. We have deposited epitaxial Gadolinia Stabilized Zirconia (GSZ) (Zr{sub 1-x}Gd{sub x}O{sub y}; x = 0-1) films on 30-nm thick e-beam evaporated Y{sub 2}O{sub 3} seeded Ni-W (3 at. %) (Ni-3W) substrates using a metal-organic decomposition (MOD) process. Detailed X-ray studies indicated that all of the MOD-GSZ layers were cube textured and both in-plane and out-of-plane lattice parameters increases linearly with increasing the Gd content. We have also developed process conditions for reactively sputter deposited epitaxial Gd{sub 2}Zr{sub 2}O{sub 7} (Gadolinium Zirconium Oxide (GZO); Zr{sub 1-x}Gd{sub x}O{sub y} (x = 0.5)) films on the e-beam evaporated Y{sub 2}O{sub 3}/Ni - 3W substrates. YBCO films with a critical current density J{sub c} of 2.14 times 10{sup 6} A/cm{sup 2} and 1.4 times 10{sup 6} A/cm{sup 2} at 77 K and self-field were grown on the newly developed architectures of Gd{sub 2}Zr{sub 2}O{sub 7}/Y{sub 2}O{sub 3}/Ni - 3W and Zr{sub 1-x}Gd{sub x}O{sub y} (x = 0.2)/Y{sub 2}O{sub 3}/Ni - 3W substrates, respectively using a pulsed laser deposition (PLD) process. This work promises a route for producing cost-effective simplified buffer architectures for the RABiTS-based YBCO coated conductors.

36 MATERIALS SCIENCE↗

Phase-Separated, Epitaxial, Nanostructured LaMnO 3 +MgO Composite Cap Layer Films for Propagation of Pinning Defects in YBa 2 Cu 3 O 7-x Coated Conductors

Nanostructural modulation in the cap layer used in coated conductors can be a potential source for nucleating microstructural defects into the superconducting layer for improving the flux-pinning. We report on the successful fabrication of phase separated, epitaxial, nanostructured films comprised of LaMnO{sub 3} (LMO) and MgO via pulsed laser deposition (PLD) on biaxially-textured MgO metallic templates with a LMO buffer layer. Scanning Auger compositional mapping and transmission electron microscopy cross sectional images confirm the nanoscale, spatial modulation corresponding to the nanostructured phase separation in the film. YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} films (0.8 {micro}m thick) grown using PLD on such phase separated, nanostructured cap layers show reduced field dependence of the critical current density with an ? value of -0.38 (in J{sub c}-H{sup -{alpha}}).

36 MATERIALS SCIENCE↗

Properties of YBCO on LaMnO3-capped IBAD MgO-templates without Homo-epitaxial MgO layer.

Previously, it has been well established that in an IBAD architecture for coated conductors, (1) LaMnO3 (LMO) buffer layers are structurally and chemically compatible with an underlying homo-epitaxial MgO layer and (2) high current density YBCO films can be grown on these LMO templates. In the present work, the homo-epi MgO layer has been successfully eliminated and a LMO cap layer was grown directly on the IBAD (MgO) template. The performance of the LMO/IBAD (MgO) samples has been qualified by depositing 1 m-thick YBCO coatings by pulsed laser deposition. Electrical transport measurements of YBCO films on the standard (with homo-epi MgO) and simplified (without homo-epi MgO) IBAD architectures were carried out. The angular dependencies of critical current density (Jc) are similar for both IBAD architectures. XRD measurements indicate good, c-axis aligned YBCO films. Transmission electron microscopy (TEM) images reveal that microstructures of YBCO/LMO/IBAD (MgO) and YBCO/LMO/homo-epi MgO/IBAD (MgO) templates are similar. These results demonstrate the strong potential of using LMO as a single cap layer directly on IBAD (MgO) for the development of a simplified IBAD architecture.

36 MATERIALS SCIENCE↗

Magnetic order in the polar intermetallic CaMn2Sb2 studied via powder neutron diffraction.

This paper reports a neutron powder diffraction study of CaMn2Sb2 in the temperature range of 20-300 K. Short-range magnetic order, characterized by a broad diffraction peak corresponding to a d spacing of 4 , is observed between 120 and 200 K. Collinear long-range antiferromagnetic order of manganese ions occurs below 85 K, where a transition is observed in the DC magnetic susceptibility measured on a single crystal. The long range antiferromagnetic order is characterized by a propagation vector k = (0 0 0) with a magnetic moment of 3.38 μB at 20 K. Two possible magnetic models have been identified, which differ in the orientation of the spins with respect to the ab plane. The model with the spins oriented at a 25(2)o angle relative to the ab plane gives an improved fit compared to the other model in which the spins are constrained to the ab plane. Representational analysis cannot account for a model involving a c-axis component without the mixing of two irreducible representations, suggesting the presence of first-order character in the phase transition.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Enhanced flux pinning in MOCVD-YBCO films through Zr-additions:Systematic feasibility studies

Systematic effects of Zr additions on the structural and flux pinning properties of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films deposited by metal-organic chemical vapor deposition (MOCVD) have been investigated. Detailed characterization, conducted by coordinated transport, x-ray diffraction, scanning and transmission electron microscopy analyses, and imaging Raman microscopy have revealed trends in the resulting property/performance correlations of these films with respect to varying mole percentages (mol%) of added Zr. For compositions {le} 7.5 mol%, Zr additions lead to improved in-field critical current density, as well as extra correlated pinning along the c-axis direction of the YBCO films via the formation of columnar, self-assembled stacks of BaZrO{sub 3} nanodots.

36 MATERIALS SCIENCE↗