Search NASA⌕ Search

Engineering topics

Parikh, Dhrupadkumar

Publications and source records attributed to Parikh, Dhrupadkumar.

Understanding slurry formulations to guide solution-processing of solid electrolytes

Scalable processing of thin solid electrolytes is crucial for engineering solid-state batteries with practical energy densities. To leverage existing battery production infrastructure, pathways for solution processing of solid electrolyte films must be investigated. Here, roll-to-roll compatible film preparation of aluminum-doped lithium lanthanum zirconate oxide was studied. Four slurry configurations accounting for different solvent properties and solid loadings were evaluated to investigate the ternary interactions within the dispersions. Rheological and coating stability analyses were carried out on the processed slurries. The analysis and characterization indicated that improved component interactions within the ethanol/toluene system result in homogenized distribution of the particles, binder, and plasticizer, and enable the extraction of free-standing thin films with thicknesses of 20 μm and large area (>15 in. 2 ). The drawbacks and opportunities of several protocols for high temperature sintering of the dried green films were investigated. This study highlights the importance of engineering dispersions during the development of processing protocols for solid electrolytes and provides guidelines for the best practices that can be leveraged for solution processing–based fabrications for a wide range of solid electrolyte materials.

25 ENERGY STORAGE↗

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗