Engineering topics

Parish, Chad [ORNL] (ORCID:0000000312097439)

Publications and source records attributed to Parish, Chad [ORNL] (ORCID:0000000312097439).

5 records

DOE OSTI2026

Using X-ray spectrum imaging to quantify fission gas in high-burnup UO2 fuel

Analysis of fission gas bubbles (FGBs) in light-water reactor (LWR) fuel is needed to improve the understanding and predictive capability of fuel evolution under normal- and transient conditions. One of the most important parameters of a FGB is the pressure of the gas, primarily Xe, inside it. Bubble volume and location (inter- vs. intragranular) are important considerations as well. However, experimental analysis of such bubbles is challenging due to their small size and embedded nature, and usefulness of the data requires large numbers be analyzed. This paper proposes a method to measure the pressure of Xe bubbles using X-ray spectrum imaging (XSI) in scanning transmission electron microscopy (STEM). From X-ray generation and instrumental parameters, the number of Xe atoms yielding a given number of Xe L-series X-ray counts is estimated, and then from the estimated volume of the bubble the Xe density is estimated, which can then be converted to pressure via an equation-of-state. We apply the method to XSI datasets from high burnup (HBu) fuel from North Anna 1 reactor in as-irradiated and post-LOCA-test conditions and find Xe pressures in the FGBs clustered around 1 GPa.

Parish, Chad [ORNL] (ORCID:0000000312097439)↗

DOE OSTI2026

The U.S. Fusion Materials Community Roadmap: Near-term research priorities for the development of plasma-facing and structural materials for fusion power plants

In response to the needs of a rapidly growing private fusion industry, the U.S. Fusion Materials Coordinating Committee (FMCC) and the broader U.S. fusion materials research community undertook an extensive effort to create a comprehensive roadmap for fusion materials development. The result of this effort was the U.S. Fusion Materials Community Roadmap (US-FMCR), which describes the steps needed to advance the technical maturity of leading candidates for plasma-facing materials and structural materials for fusion power plants from laboratory-scale experiments to a point of sufficient technological readiness for industrial adoption and implementation. However, researchers face significant resource constraints as well as very aggressive pilot plant development timelines. Thus, the research strategies detailed in the US-FMCR require further assessment to downselect the specific tasks that must be prioritized within the next two to three years, in order to make the most efficient use of funding, human resources, and experimental facilities. This paper presents an overview of the US-FMCR and its development process. We also present the subset of research objectives that the FMCC identified as the most urgent research priorities for the U.S. fusion materials research community. The state-of-the-art of materials research is also highlighted for each class of materials considered in the US-FMCR. The recommendations presented here integrate an extensive evaluation of the current status of fusion materials research with a broad cross-section of opinion from the wider U.S. fusion community.

Ferry, Sara [Massachusetts Institute of Technology↗

DOE OSTI2026

Hierarchical microstructure of Yb-filled skutterudites through ultrasonically atomized spherical powders for enhanced thermoelectric performance

Hierarchical microstructures are widely explored as a strategy to reduce lattice thermal conductivity in thermoelectric materials while preserving favorable electronic transport. Here we demonstrate that ultrasonic atomization of precursor powders provides an intrinsic pathway to generate such architectures in n-type Yb0.3Co4Sb12 skutterudites. Materials were synthesized by both conventional sealed-ampoule and ultrasonic atomization routes, each yielding essentially single-phase skutterudite after densification. However, the atomized spherical powders undergo a distinct reaction-driven microstructural evolution during thermal treatment prior to densification. Electron microscopy reveals that the skutterudite phase within the particles induces swelling, cracking, and fragmentation of the droplets before consolidation. Multimodal structural and microstructural characterizations show that densification of these fragmented powders produces a hierarchical microstructure consisting of submicron grains, micrometer-scale faceted crystallites, and powder-derived domains separated by oxide-decorated boundaries. Comprehensive thermoelectric transport measurements evidence that this multiscale architecture lowers the lattice thermal conductivity while maintaining favorable electronic transport, leading to an average ~10% enhancement in the thermoelectric figure of merit. Complementary 121Sb Mössbauer spectroscopy further indicates lattice softening in the atomized material. These results demonstrate that ultrasonic atomization provides an effective route to engineer hierarchical microstructures in skutterudite thermoelectrics and offers a promising strategy for tailoring thermal transport in energy-conversion materials.

Bouteiller, Hugo [ORNL] (ORCID:0009000421322962)↗

DOE OSTI2026

Identifying microstructures susceptible to pulverization in commercially irradiated high burnup UO2 under LOCA conditions

High burnup fuel fragmentation (HBFF) has been a concern in the nuclear industry for many years. When UO2 reaches and exceeds pellet average burnups around 55 GWd/tU, microstructural changes in the fuel pellet begin to occur that render the pellet susceptible to fine fragmentation under loss-of-coolant accident (LOCA) conditions. During a LOCA event, the cladding balloons and bursts, potentially releasing part of these fine fuel fragments into the reactor pressure vessel. This process is known as fuel fragmentation, relocation, and dispersal (FFRD). Presently, the US nuclear industry is developing a safety basis for FFRD with the goal of increasing burnups and pressurized water reactor cycle lengths. Increased cycle lengths would push the burnup limits of the fuel rods past the known threshold for HBFF susceptibility. In this work, the microstructural impact on HBFF was investigated by comparing the microstructures of as-irradiated rod segments to their post-LOCA tested counterparts. This investigation found that varied operational histories result in different microstructural evolutions across the pellet radius, which impacts the fragmentation behavior and radial location of the fragmentation. It is noted that regions with a high bubble density and a high density of grain boundaries fragment under LOCA-relevant conditions. In addition to the fragmentation that has been previously reported at the periphery of the fuel, fragmentation was also noted in the dark zone toward the fuel center. Analysis of the power histories of the fuel samples suggests that the dark zone forms in the central regions of the pellet between temperatures of approximately 740 and 960 °C.

McKinney, Casey [ORNL] (ORCID:0000000335383614)↗

DOE OSTI2025

XPS post-mortem analysis of plasma-facing units extracted from WEST after the C3 (2018) and C4 (2019) campaigns

Four monoblocks coming from one ITER-like plasma-facing unit from the Q3B sector of the lower divertor, named as monoblock (MB)3, MB9, MB20, and MB30, were exposed to the deuterium and helium plasma mixture during the C3 (2018) and C4 (2019) campaigns of the Tungsten Environment in Steady-state Tokamak (WEST), followed by a detailed ex-situ X-ray photoelectron spectroscopy investigation. The surface and in-depth chemistry of the tungsten monoblocks indicated the formation of a re-deposited mixture in the deposition-dominated area of the divertor, thicker than 218 and 172 nm for MB3 and MB9, respectively. The redeposition layer was dominated by a mixture of boron carbides accompanied by tungsten carbides in MB3, while in MB9, the redeposition layer was dominated by tungsten borides. The remaining two monoblocks, MB20 and MB30, were collected from the erosion region and showed similar chemical behavior with a blended mixture of oxidized and metallic tungsten followed by boron carbides within a 50 nm depth range. Boron fixation in the layers is an expected consequence of the boronizations used during the operation, but the chemical status of redeposited elements was characterized for the first time in this work.

Marin, Alexandru [Pennsylvania State University]↗