Post-Irradiation Examination of 3D-Printed SiC
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Parish, Chad.
Explore the source record for details and available documents.
Tungsten (W) has been perceived as one of the most promising plasma facing materials (PFMs) for future fusion reactors. In the past decade, its behavior under irradiation and helium (He) plasma interaction has been extensively studied. However, some key knowledge gaps still exist, such as the influence of crystallographic orientation on the surface and subsurface evolutions. In this work, we focus on the He ion-beam irradiation damage effects in mirror-polished single-crystalline W samples with three different surface planes of {100}, {110} and {111}. Irradiation was performed at room temperature using 40 keV He+ to a fluence of 1 × 10 16 /cm 2 , followed by thermal desorption spectroscopy (TDS) up to ~1920 K. The microstructures of He-irradiated W before and after TDS heat treatment were characterized by scanning and transmission electron microscopy. Subsurface He bubbles were imaged in all irradiated samples, but newly formed <111>-oriented surface grains and surface blisters were only observed in W {100} and {110} starting orientations. These results reveal that radiation damage, He thermal desorption, and surface/subsurface evolution are all strongly dependent on crystallographic orientation. Underlying physical mechanisms are discussed based on ion channeling effects, He-vacancy interactions, and surface diffusion. In conclusion, these findings provide new insights into He effects in W.
Explore the source record for details and available documents.
Tungsten is the primary candidate for plasma-facing materials in the critical regions of a magnetic fusion energy (MFE) device, such as a tokamak. However, tungsten (and many other metals) grow copious nanotendril "fuzz" when exposed to fusion-relevant He-bearing plasmas, and the impact of this fuzz on reactor operation is still unknown. Further, the mechanism of fuzz growth is also poorly understood at present. In order to experimentally probe the growth mechanisms, we developed a new sample preparation technique to examine the interface of individual nanotendril roots with the substrate (substrate/tendril interface) using electron microscopy and measured the grain boundary character distributions (GBCDs) of substrate/tendril interfaces, the GBs within individual tendrils (tendril/tendril interfaces), and GBs within the substrate (substrate/substrate interfaces). We find the substrate/tendril and tendril/tendril GBCDs are essentially indistinguishable, but very different from the substrate/substrate GBCDs, which implies that tendril growth periodically forms new GBs at the substrate/tendril interface, and these GBs are pushed upward to become tendril/tendril interfaces within the fuzz mat. These results will help guide future computational modelling studies to elucidate the details of the growth mechanisms.
Explore the source record for details and available documents.
New candidate materials for GenIV or fusion nuclear energy systems, e.g., nanostructured ferritic alloys, are distinguished from older-generation nuclear materials by much smaller feature sizes and complex local nanochemistry and crystallography. Established and perspective nuclear materials, e.g. reactor pressure vessel steels or plasma-facing tungsten, also form small nanoscale structures under in-reactor service. Here, we discuss recent advances in materials characterization – high-efficiency X-ray mapping combined with datamining; transmission Kikuchi diffraction; and atom probe tomography – that make it possible to quantitatively characterize these nanoscale structures in unprecedented detail, which enables advances in understanding and modelling of radiation service and degradation.
Ultrasonic additive manufacturing (UAM) is a solid-state process, which uses ultrasonic vibrations at 20 kHz along with mechanized tape layering and intermittent milling operation, to build fully functional three-dimensional parts. In the literature, UAM builds made with low power (1.5 kW) exhibited poor tensile properties in Z-direction, i.e., normal to the interfaces. This reduction in properties is often attributed to the lack of bonding at faying interfaces. The generality of this conclusion is evaluated further in 6061 aluminum alloy builds made with very high power UAM (9 kW). Tensile deformation behavior along X and Z directions were evaluated with small-scale in-situ mechanical testing equipped with high-resolution digital image correlation, as well as, multi-scale characterization of builds. Interestingly, even with complete metallurgical bonding across the interfaces without any discernable voids, poor Z-direction properties were observed. This reduction is correlated to coalescence of pre-existing shear bands at interfaces into micro voids, leading to strain localization and spontaneous failure on tensile loading.
The epitaxially stabilized metallic α - FeSi 2 thin films on Si(001) were grown using pulsed laser deposition. While the bulk material of α - FeSi 2 is a high temperature metastable phase and nonmagnetic, the thin film is stabilized at room temperature and shows unusual electronic transport and magnetic properties due to strain modification. The transport renders two different conducting states with a strong crossover at 50 K accompanied by an onset of ferromagnetism as well as a substantial magnetocaloric effect and magnetoresistance. These experimental results are discussed in terms of the unusual electronic structure of α - FeSi 2 obtained within density functional calculations and Boltzmann transport calculations with and without strain. Our findings provide an example of a tailored material with interesting physics properties for practical applications.
Explore the source record for details and available documents.
The goal of the current project was to help make the US solar industry a world leader in the manufacture of thin film photovoltaics. The overall approach was to leverage ORNL’s unique characterization and processing technologies to gain a better understanding of the fundamental challenges for solar cell processing and apply that knowledge to targeted projects with industry members. ORNL has the capabilities in place and the expertise required to understand how basic material properties including defects, impurities, and grain boundaries affect the solar cell performance. ORNL also has unique processing capabilities to optimize the manufacturing process for fabrication of high efficiency and low cost solar cells. ORNL recently established the Center for Advanced Thin-film Systems (CATS), which contains a suite of optical and electrical characterization equipment specifically focused on solar cell research.
Erbium metal thin-films have been deposited on molybdenum-on-silicon substrates and then converted to erbium dideuteride (ErD{sub 2}). Here, we study the effects of deposition temperature ({approx}300 or 723 K) and deposition rate (1 or 20 nm/s) upon the initial Er metal microstructure and subsequent ErD{sub 2} microstructure. We find that low deposition temperature and low deposition rate lead to small Er metal grain sizes, and high deposition temperature and deposition rate led to larger Er metal grain sizes, consistent with published models of metal thin-film growth. ErD{sub 2} grain sizes are strongly influenced by the prior-metal grain size, with small metal grains leading to large ErD{sub 2} grains. A novel sample preparation technique for electron backscatter diffraction of air-sensitive ErD{sub 2} was developed, and allowed the quantitative measurement of ErD{sub 2} grain size and crystallographic texture. Finer-grained ErD{sub 2} showed a strong (1 1 1) fiber texture, whereas larger grained ErD{sub 2} had only weak texture. We hypothesize that this inverse correlation may arise from improved hydrogen diffusion kinetics in the more defective fine-grained metal structure or due to improved nucleation in the textured large-grain Er.