Engineering topics
Park, Yensil
Publications and source records attributed to Park, Yensil.
Alkylperoxy radicals are responsible for the formation of oxygenated primary organic aerosol
Organic aerosol (OA) is an air pollutant ubiquitous in urban atmospheres. Urban OA is usually apportioned into primary OA (POA), mostly emitted by mobile sources, and secondary OA (SOA), which forms in the atmosphere due to oxidation of gas-phase precursors from anthropogenic and biogenic sources. By performing coordinated measurements in the particle phase and the gas phase, we show that the alkylperoxy radical chemistry that is responsible for low-temperature ignition also leads to the formation of oxygenated POA (OxyPOA). OxyPOA is distinct from POA emitted during high-temperature ignition and is chemically similar to SOA. We present evidence for the prevalence of OxyPOA in emissions of a spark-ignition engine and a next-generation advanced compression-ignition engine, highlighting the importance of understanding OxyPOA for predicting urban air pollution patterns in current and future atmospheres.
Detailed hydrocarbon speciation and particulate matter emissions during cold-start from turbocharged and naturally aspirated trucks
Not Available
Impact of Biofuel Blending on Hydrocarbon Speciation and Particulate Matter from a Medium-Duty Multimode Combustion Strategy
The U.S. Department of Energy’s Co-Optima initiative simultaneous focused on diversifying fuel sources, improving efficiency, and reducing emissions through using novel combustion strategies and sustainable fuel blends. For medium-duty/heavy-duty diesel engines, research in this area has led to the development of a multimode strategy that uses premixed charge compression ignition (PCCI) at low loads and conventional diesel combustion (CDC) at mid–high loads. The aim of this study was to understand how emissions were impacted when using PCCI instead of CDC at low loads and switching to an oxygenated biofuel blend. It provides a detailed speciation of the hydrocarbon (HC) and particulate matter (PM) emissions from a multimode medium-duty engine operating at low loads in PCCI and CDC modes and high loads in CDC. The effect of the oxygenated biofuel blend on emissions was studied at all three mode–load conditions using #2 ULSD and a bio-derived fuel (25% hexyl hexanoate (HHN)) blended in #2 ULSD. The PCCI mode effectively decreased NOx, total HC, and PM/PN emissions, with a substantial decrease in larger particles (≥50 nm). A PM/PN reduction was observed at high loads with the 25% HHN fuel. While the total HC emissions were not impacted by fuel type, the detailed HC analysis exposed changes in the HC’s composition.
Microwave Regeneration and Thermal and Oxidative Stability of Imidazolium Cyanopyrrolide Ionic Liquid for Direct Air Capture of Carbon Dioxide
Abstract Understanding the oxidative and thermal degradation of CO 2 sorbents is essential for assessing long‐term sorbent stability in direct air capture (DAC). The potential degradation pathway of imidazolium cyanopyrrolide, an ionic liquid (IL) functionalized for superior CO 2 capacity and selectivity, is evaluated under accelerated degradation conditions to elucidate the secondary reactions that can occur during repetitive absorption‐desorption thermal‐swing cycles. The combined analysis from various spectroscopic, chromatographic, and thermal gravimetric measurements indicated that radical and S N 2 mechanisms in degradation are encouraged by the nucleophilicity of the anion. Thickening of the liquid and gas evolution are accompanied by 50 % reduction in CO 2 capacity after a 7‐day exposure to O 2 under 80 °C. To prevent long exposure to conventional thermal heating, microwave (MW) regeneration of the CO 2 ‐reactive IL is used, where dielectric heating at 80 and 100 °C rapidly desorbs CO 2 and regenerates the IL without any measurable degradation.
Impact of Hydrogen Bonds on CO 2 Binding in Eutectic Solvents: An Experimental and Computational Study toward Sorbent Design for CO 2 Capture
Choline-based amino acid ionic liquids with anions glycinate, β-alaninate, phenylalaninate, and prolinate were synthesized and mixed with ethylene glycol to form lower-viscosity benign eutectic solvents for CO 2 capture. The highest capacity measured was 0.7 moles of CO 2 per mole of ionic liquid (2 moles CO 2 per kg solvent) for a 1 to 2 mole ratio mixture of choline prolinate to ethylene glycol at 1 bar of CO 2 and 25 °C. Under 5000 ppm of CO 2 , half of this capacity was realized. Here, through a combined study of quantitative 13 C NMR spectroscopy, molecular dynamics simulations and density functional theory calculations, we show that hydrogen bonding in the eutectic solvent prevents proton-transfer between prolinate anions upon CO 2 absorption, which occurs in the absence of ethylene glycol and deactivates binding sites. Blocking this proton transfer leads to a higher binding capacity compared to neat choline prolinate. This work demonstrates the impact of hydrogen bonding on the CO 2 binding mechanism and energetics, as well as physical and thermal properties in eutectic solvents, thus addressing an unmet need and informing future studies on the development of benign sorbents for capturing CO 2 from dilute streams.
Spray Pyrolysis-Aerosol Deposition for the Production of Thick Yttria-Stabilized Zirconia Coatings
Aerosol deposition (AD) is a coating technique wherein particles are impacted onto a target substrate at reduced pressures, and supersonic particle impact velocities lead to coating consolidation. The limiting step in AD application is often not supersonic deposition operation, but aerosolization of powder particles with the proper size distribution; the translational impact velocity is strongly size-dependent. It is demonstrated that by directly synthesizing particles in the gas phase, size-controlled ceramic particles can be injected into AD systems. This in situ formation step obviates the need for particle aerosolization. Ultrasonic spray pyrolysis (USP) is applied to produce yttria-stabilized zirconia (YSZ), and USP is directly coupled with AD to produce consolidated, thick, YSZ coatings on metal substrates. USP-AD yields YSZ coatings on stainless steel and aluminum substrates with porosities <0.20, which grow to thicknesses beyond 100 μm. Aerodynamic particle spectrometry and electron microscopy reveal that the depositing particles are 200 nm–1.2 μm in diameter, though each particle is composed of nanocrystalline YSZ. Supporting computational fluid dynamics calculations demonstrate that the YSZ particle impact speeds are above 300 m s -1 . Thermal conductivity measurements demonstrate that USP-AD coatings have conductivities consistent with those produced from high-temperature processes.