Search NASA⌕ Search

Engineering topics

Parks, David

Publications and source records attributed to Parks, David.

Combined crystal plasticity and grain boundary modeling of creep in ferritic-martensitic steels: II. The effect of stress and temperature on engineering and microstructural properties

This paper describes a series of physically-based crystal plasticity finite element method (CPFEM) simulations of long-term creep and creep rupture of Grade 91 steel. It is Part 2 of a two part series of papers. Part 1 describes the simulation framework; this part focuses on specific simulations and on how the predicted long-term creep properties of Grade 91 compare to the assumptions used in current high temperature design practices. This work extends the model developed in Part 1 to look at creep properties at different temperatures, principal stresses, and multiaxial stress states. The simulations show that empirically extrapolating creep rupture stresses from short-term experimental data may substantially over predict the actual long-term creep properties of Grade 91. Additionally, the CPFEM calculations predict a transition from notch strengthening creep behavior for high values of maximum principal stress and moderate notch severity to notch weakening behavior for low principal stresses and more severe notches. The latter regime better categorizes conditions in engineering components designed for long term elevated temperature use, which implies Grade 91 may be a notch weakening material in actual service. This would have a significant impact on high temperature design practices, though confirmatory test data on long-life, low stress notched specimens is difficult to obtain. Finally, one advantage of the physically-based modeling approach adopted here is that the simulation results also elucidate the microstructural mechanisms causing the macroscopic trends in engineering properties predicted by the simulations. This paper shows that the detailed micromechanical mechanisms predicted by the CPFEM simulations can be abstracted with a simple micromechanical model that can be used to both explain the detailed results and make improved predictions of engineering properties from experimental data.

36 MATERIALS SCIENCE↗

Summary report describing CASL accomplishments in support of the GTRF Challenge Problem

Coolant flow-induced relative motions between structural components in the cores of lightwater nuclear reactor cores, a phenomenon called Grid-To-Rod Fretting (GTRF), can result in progressive wear damage. Wear-through of the cladding on fuel rods can introduce radioactive species into the coolant loop. Such an event is termed a “leaker” and may cause premature and expensive reactor shut-down. GTRF results in wear scars of various sizes, shapes, and depths on the sides of the fuel rod cladding. Fretting damage may also occur on the springs and dimples that hold the fuel rods in place, resulting in the formation of gaps. Due to variability in the operating conditions of the reactor (burn-up rates and operating campaigns) and the associated variable cladding surface oxide film growth and removal rates, the wear coefficient is unlikely to remain constant over time. Therefore, constant wear rate models do not accurately account for transients in the operating conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Data File Standard for Flow Cytometry, Version FCS 3.1

The flow cytometry data file standard provides the specifications needed to completely describe flow cytometry data sets within the confines of the file containing the experimental data. In 1984, the first Flow Cytometry Standard format for data files was adopted as FCS 1.0. This standard was modified in 1990 as FCS 2.0 and again in 1997 as FCS 3.0. We report here on the next generation flow cytometry standard data file format. FCS 3.1 is a minor revision based on suggested improvements from the community. The unchanged goal of the standard is to provide a uniform file format that allows files created by one type of acquisition hardware and software to be analyzed by any other type. The FCS 3.1 standard retains the basic FCS file structure and most features of previous versions of the standard. Changes included in FCS 3.1 address potential ambiguities in the previous versions and provide a more robust standard. The major changes include simplified support for international characters and improved support for storing compensation. The major additions are support for preferred display scale, a standardized way of capturing the sample volume, information about originality of the data file, and support for plate and well identification in high throughput, plate based experiments. Please see the normative version of the FCS 3.1 specification in Supporting Information for this manuscript (or at http://www.isac-net.org/ in the Current standards section) for a complete list of changes.

59 BASIC BIOLOGICAL SCIENCES↗