Search NASA⌕ Search

Engineering topics

Parks, P B

Publications and source records attributed to Parks, P B.

Modeling of Lithium Granule Injection in NSTX with M3D-C1

In this paper we present initial simulations of pedestal control by Lithium Granule Injection (LGI) in NSTX. A model for small granule ablation has been implemented in the M3D-C1 code [1], allowing the simulation of realistic Lithium granule injections. 2D simulations in NSTX L-mode and H-mode plasmas are done and the effect of granule size, injection angle and velocity on the pedestal gradient increase are studied. For H-mode cases, the amplitude of the local pressure perturbation caused by the granules is highly dependent on the solid granule size. In our simulations, reducing the granule injection velocity allows one to inject more particles at the pedestal top.

Fil, A↗

Effect of Applied Toroidal Electric Field on the Growth/Decay of Plateau-Phase Runaway Electron Currents in DIII-D

Large relativistic runaway electron currents (0.1-0.5 MA) persisting for similar to 100 ms are created in the DIII-D tokamak during rapid discharge shut down caused by argon pellet injection. Slow upward and downward ramps in runaway currents were found in response to externally applied loop voltages. Comparison between the observed current growth/decay rate and the rate expected from the knock-on avalanche mechanism suggests that classical collisional dissipation of runaways alone cannot account for the measured growth/damping rates. It appears that a fairly constant anomalous dissipation rate of order 10 s(-1) exists, possibly stemming from radial transport or direct orbit losses to the vessel walls, although the possibility of an apparent loss due to current profile shrinking cannot be ruled out at present.

Hollmann, E M↗

Pellet interaction with runaway electrons

We describe results from recent experiments studying interaction of solid polystyrene pellets with a runaway electron current channel generated after cryogenic argon pellet rapid shutdown of DIII-D. Fast camera imaging shows the pellet trajectory and continuum emission from the subsequent explosion, with geometric calibration providing detailed explosion analysis and runaway energy. Electron cyclotron emission also occurs, associated with knock-on electrons broken free from the pellet by RE which then accelerate and runaway, and also with a short lived hot plasma blown off the pellet surface. In addition, we compare heating and explosion times from observations and a model of pellet heating and breakdown by runaway interaction. (C) 2011 Elsevier B.V. All rights reserved

43 PARTICLE ACCELERATORS↗

Plasma-surface interactions during tokamak disruptions and rapid shutdowns

Recent progress in understanding of disruptions and in developing methods to avoid disruption damage is presented. Nearly complete mitigation of conducted heat loads has been achieved with high-Z gas jet shutdown. The resulting local radiation heat flash melting in the main chamber might be a concern in ITER, especially with beryllium walls. During the current quench, significant vessel forces can occur due to halo currents I-halo; however, these are found to fall reliably below a boundary of (halo current fraction times halo current peaking factor) <0.7 both experimentally and numerically. Numerical simulations indicate that runaway electrons (REs) could cause serious damage to hard-to reach components in ITER, making their suppression a high priority. During the current quench, less than 20% of the density required for collisional suppression of REs appears to have been achieved. Collisional suppression of REs may have been achieved, however, in full-current RE beams with gas injection. (C) 2010 Elsevier B.V. All rights reserved.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Demonstration of rapid shutdown using large shattered deuterium pellet injection in DIII-D

A severe consequence of a disruption on large tokamaks such as ITER could be the generation of multi-megaelectronvolt electron beams that could damage the vacuum vessel and the structures of the machine if they hit the wall unmitigated. The mitigation of runaway electron beams is thus a key requirement for reliable operation of ITER. In order to achieve reliable disruption mitigation, a new fast shutdown technique has been developed: the injection of a large shattered cryogenic pellet in the plasma, which is expected to increase the electron density up to levels where the beam generation processes are mitigated by collisional losses. This technique has been implemented and tested for the first time ever on DIII-D. The first tests show evidence of an almost instantaneous deposition of more than 260 Pa m(3) of deuterium deep in the core. Record local densities during the thermal quench were observed for each injection with a very high reliability. Pellet mass and plasma energy content scans show an improvement of the assimilation of the particles for higher plasma energy and larger pellet mass.

Commaux, Nicolas JC↗

Experiments in DIII-D toward achieving rapid shutdown with runaway electron suppression

Experiments have been performed in the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] toward understanding runaway electron formation and amplification during rapid discharge shutdown, as well as toward achieving complete collisional suppression of these runaway electrons via massive delivery of impurities. Runaway acceleration and amplification appear to be well explained using the zero-dimensional (0D) current quench toroidal electric field. 0D or even one-dimensional modeling using a Dreicer seed term, however, appears to be too small to explain the initial runaway seed formation. Up to 15% of the line-average electron density required for complete runaway suppression has been achieved in the middle of the current quench using optimized massive gas injection with multiple small gas valves firing simultaneously. The novel rapid shutdown techniques of massive shattered pellet injection and shell pellet injection have been demonstrated for the first time. Experiments using external magnetic perturbations to deconfine runaways have shown promising preliminary results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of the low order rational q surfaces on the pellet deposition profile

Pellet injection is planned to be the main fuelling method on ITER. The high temperature of the plasma during a fusion burn will limit the penetration of the pellet to the outer third of the minor radius. This limited penetration is expected to be compensated by a polarization drift, which will deposit the particles deeper in the plasma for the pellets injected from the high field side. In order to evaluate the expected depth of the fuelling on ITER, a good understanding of this drift effect is important. Experimental data acquired on the DIII-D (USA) and Tore Supra (France) tokamaks show that the polarization drift is influenced by the low order rational q surfaces. These surfaces appear to attenuate the polarization mechanism as the drifting particles cross them. In this paper, a correlation between the maximum of the pellet mass deposition profile and the positions of the q = 2 and q = 3 surfaces on DIII-D and Tore Supra is shown for high field side and low field side injection. A model is proposed to explain this effect and compared with the experimental results. To conclude, the possible consequences of this phenomenon on the fuelling in ITER are described.

Commaux, Nicolas JC↗

Low-Z Shell Pellet Experiments on DIII-D

Small (o.d. = 1.8 mm, t = 0.37 mm) polystyrene shells filled with either pressurized argon gas or boron powder have been fired into DIII-D plasmas for disruption mitigation experiments. The pellet shells were observed to burn up at rhoapprox =0.5, roughly consistent with ablation rate calculations. Pellet slowing from 350 m/s down to 100 m/s was observed, which is not well-understood at present. Negligible plasma current contraction or MHD onset were seen as a result of the shell burn-up in the plasma edge, consistent with calculations. The pellet payloads were observed to ionize rapidly in the pellet vicinity (<1 cm radius) and rapid (<15 ms) mixing through the plasma core was observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Charging and ExB rotation of ablation clouds surrounding refueling pellets in hot fusion plasmas

The finite resistivity magnetohydrodynamic code FRONTIER-MHD[R. Samulyak et al., Nucl. Fusion 47, 103 (2007)] is used to simulate the ablation rate of refueling pellets, including the novel effect of electrostatically induced ExB rotation of the ablation cloud about its symmetry axis parallel to the magnetic field. The key finding is that the centrifugal force of cloud rotation pushes the cloud density radially outwards, creating a more ''transparent'' ablation channel. With reduced shielding, the steady state ablation rate of a deuterium pellet significantly increases from {approx}35% to 100%, depending on the B-field strength. This new effect brings the ablation rate into better accord with a known theoretical scaling law, which agrees with most current experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗