Search NASA⌕ Search

Engineering topics

Parks, P. B.

Publications and source records attributed to Parks, P. B..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Self-consistent investigation of density fueling needs on ITER and CFETR utilizing the new Pellet Ablation Module

Abstract Self-consistent modeling using the stability, transport, equilibrium, and pedestal (STEP) workflow in the OMFIT integrated modeling framework (predicting pedestal with EPED, core profiles with TGYRO, current profile with ONETWO, and EFIT for equilibrium) suggests ITER and future devices such as China Fusion Engineering Test Reactor (CFETR) Zhuang et al (2019 Nucl. Fusion 59 112010) will benefit from high-density operation (Greenwald limit fraction f g w ≈ 0.7−1.3). Regimes with an operational density near the Greenwald limit will likely need peaked density profiles so that the pedestal density remains below the Greenwald limit. Peaked density profiles can be achieved with the help of pellet injection. A flexible Pellet Ablation Module (PAM), which predicts the density source based on a comprehensive analytical pellet ablation model, has been developed for predicting pellet fueling for transport studies, and has been incorporated into the STEP workflow for predictive modeling. This workflow is applied to DIII-D and finds good agreement with experiments. On ITER the effect of pellet fueling is examined in an advanced inductive scenario, where a fusion gain of up to Q = 9 is predicted with strong central pellet fueling. On CFETR, with a mid-radius density source, an average of 1.5 × 10 22 electrons s −1 are required to achieve the density and temperature profiles necessary for the 1000 MW advanced scenario with a tritium burn-up fraction of ∼ 3 % .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Estimate of pre-thermal quench non-thermal electron density profile during Ar pellet shutdowns of low-density target plasmas in DIII-D

The radial density profile of pre-thermal quench (pre-TQ) early-time runaway electrons (REs) is estimated by combining electron cyclotron emission (ECE) and soft x-ray (SXR) data during rapid shutdown of low-density (n e ≲ 10 13 cm -3 ) DIII-D target plasmas with cryogenic argon pellet injection. This technique is limited in these experiments to the pre-TQ phase and quickly loses validity during the TQ. Two different cases are studied: a high (10 keV) temperature target and a lower (4 keV) temperature target. The results indicate that early-time, low-energy (~10 keV) REs form ahead of the argon pellet as it enters the plasma, affecting the pellet ablation rate; it is hypothesized that this may be caused by rapid cross-field transport of argon ions ahead of the pellet. Fokker-Planck modeling of the two shots suggests that the RE current is quite significant during the pre-TQ phase (up to 50% of the total current). Comparison between modeled pre-TQ RE current and post-TQ RE current inferred from avalanche theory suggests that RE current increases during the high temperature target TQ but decreases during the low temperature target TQ. Here, the uncertainties in this estimate are large; but, if true, this suggests that TQ loss of REs can be larger than previously estimated in DIII-D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Toroidal modeling of runaway avalanche in DIII-D discharges

Abstract A toroidal modeling tool is developed to study the runaway electron (RE) avalanche production process in tokamak plasmas, by coupling the Rosenbluth–Putvinski avalanche model (Rosenbluth and Putvinski 1997 Nucl. Fusion 37 1355) with an n = 0 magneto-hydrodynamic (MHD) solver. Initial value numerical simulations are carried out for two DIII-D discharges with different plasma shapes (one near circular, and the other with high elongation). It is found that, assuming the same level of about 1% seed current level, the Rosenbluth–Putvinski model somewhat underestimates the RE plateau current for the circular-shaped plasma, as compared with that measured in DIII-D experiments. For an elongated, higher current plasma, simulations find strong runaway current avalanche production despite the lack of measured plateau RE current in experiments. A possible reason for this discrepancy is a lack of additional RE dissipation physics in the present two-dimensional model. Systematic scans of the plasma boundary shape, at fixed pre-disruption plasma current, find that the plasma elongation helps to reduce the RE avalanche production, confirming recent results obtained with an analytic model (Fülöp et al 2020 J. Plasma Phys. 86 474860101). The effect of the plasma triangularity (either positive or negative), on the other hand, has a minor effect. On the physics side, the avalanche process involves two competing mechanisms associated with the electric field. On the one hand, a stronger electric field produces a higher instantaneous avalanche growth rate. On the other hand, a fast growing RE current quickly reduces the fraction of the conduction current together with the electric field, and hence a faster dissipation of the poloidal flux. As a final result of these two dynamic processes, the runaway plateau current is not always the largest with the strongest initial electric field. These results lay the foundation for future self-consistent inclusion of the MHD dynamics and the RE amplification process.

Physics↗
DOE OSTI2021

Numerical simulation of the hot-tail runaway electron production mechanism using CQL3D and comparison with Smith–Verwichte analytical model

Abstract The hot-tail mechanism of runaway electron (RE) production (Harvey et al 2000 Phys. Plasmas 7 4590) is the primary source of RE in the case of rapidly cooling tokamak plasma. Quantifying this mechanism is very important as it can provide most of the post-thermal-quench (TQ) current, or a seed current for the secondary source of RE through the avalanche mechanism. An analytic model which omits pitch-angle scattering is often used in literature for estimating the hot-tail RE density (Smith and Verwichte 2008 Phys. Plasmas 15 072502). In the present study, we use the CQL3D bounce-averaged Fokker–Planck code (Harvey and McCoy 1992 Proc. IAEA Technical Committee Meeting on Advances in Simulation and Modeling of Thermonuclear Plasmas p 527) to test the limits of validity of the model. In particular, we examine the cases of Z = 1 and Z = 18 ions, for sets of different initial temperature, density, electric field and the characteristic time of temperature decay. We show that for Z = 1 plasma, the ratio of RE density computed by CQL3D to that estimated from the model is within 0.6–6.0 in studied cases. For the Z = 18 case, this factor is systematically a much smaller number, typically 0.02–0.6. We suggest a simple correction to the model that narrows down the range of this ratio to 0.3–3.8 in all of the cases, including Z = 1 and Z = 18 plasmas.

Physics↗
DOE OSTI2020

Observation of non-thermal electron formation during the thermal quench of shattered pellet injection shutdowns in DIII-D

Formation of non-thermal (hot) electrons is studied during the thermal quench of shattered pellet injection (SPI) discharge shutdowns in the DIII-D tokamak. Both pure neon and mixed neon/deuterium shutdowns are studied. High-energy radiation (SXR and EUV) brightness levels show indications of non-thermal electron formation during the TQ. The non-thermal densities are of order 10 18 m –3 and non-thermal temperatures are estimated to be of order 10 keV. The non-thermal electrons appear to be mostly lost during the subsequent current quench, as no signal of relativistic runaway electrons is typically seen at the end of the current quench. In conclusion, the non-thermals appear to have an effect on the deposition profile of the SPI pellets, especially at the end of the TQ, due to increased pellet ablation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Toroidal modeling of runaway electron loss due to 3-D fields in DIII-D and COMPASS

The 3-D field induced relativistic runaway electron (RE) loss has been simulated for DIII-D, COMPASS and ITER plasmas, utilizing the MARS-F code incorporated with the recently developed and updated RE orbit module (REORBIT). Modeling shows effectively 100% loss of a post-disruption, high-current runaway beam in DIII-D, due to the 1 kG level of magnetic field perturbation produced by a fast growing n = 1 resistive kink instability. The RE loss is shown to be independent of the particle energy or the initial location of particles in the configuration space. Applied resonant magnetic perturbation (RMP) fields from in-vessel coils are not effective for RE beam mitigation in DIII-D, but do produce finite (>10%) RE loss in COMPASS, consistent with experimental observations in above two devices. The major reasons for this difference in RE control by RMP between these two devices are (i) the coil proximity to the RE beam and (ii) the effective coil current scaling versus the machine size and the toroidal magnetic field. About 10% RE loss fraction is also predicted for an ITER 15 MA scenario with pre-disruption plasma, highlighting the role of the plasma response. Up to 30% loss is computed, however, by artificially scaling the equilibrium pressure to zero. This is due to the more resistive plasma response and stronger resulting field line stochasticity. Distributions of the lost REs to the limiting surface show poloidally peaked profile near the high-field-side in both DIII-D and COMPASS, covering about 100o poloidal angle. Higher perturbation field level and/or higher particle energy also result in REs being lost to the low-field-side of the limiting surface of these two devices, increasing the effective wetted area. Finally, for the modeled ITER plasmas, the applied RMP field, with optimal poloidal spectrum that maximizes the edge localized mode control, leads to REs being lost to the lower divertor region of the limiting surface within a narrow poloidal band.

3-D field↗
DOE OSTI2020

Study of argon expulsion from the post-disruption runaway electron plateau following low-Z massive gas injection in DIII-D

Herein, a 1D radial diffusion model is developed to study the observed rapid expulsion of argon from the runaway electron plateau in the DIII-D tokamak following secondary massive low-Z (D 2 or He) gas injection. The expulsion of argon is found to be caused by further cooling of the background plasma due to the added neutrals, accompanied by recombination of argon ions and greatly increased outward radial transport rate of argon (now dominantly in neutral form) out of the runaway electron beam. After argon expulsion, power loss out of the runaway electron plateau is found to be dominated by neutral transport to the wall (rather than by radiation); this result resolves the power balance discrepancy highlighted in previous work on argon expulsion out of the runaway electron plateau.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1994

Uniform hydrogen fuel layers for inertial fusion targets by microgravity

A critical concern in the fabrication of targets for inertial confinement fusion (ICF) is ensuring that the hydrogenic (D(sub 2) or DT) fuel layer maintains spherical symmetry. Solid layered targets have structural integrity, but lack the needed surface smoothness. Liquid targets are inherently smooth, but suffer from gravitationally induced sagging. One method to reduce the effective gravitational field environment is freefall insertion into the target chamber. Another method to counterbalance field gravitational force is to use an applied magnetic field combined with a gradient field to induce a magnetic dipole force on the liquid fuel layer. Based on time dependent calculations of the dynamics of the liquid fuel layer in microgravity environments, we show that it may be possible to produce a liquid layered ICF target that satisfies both smoothness and symmetry requirements.

Parks, P. B.↗