Engineering topics

Parmley, Richard T.

Publications and source records attributed to Parmley, Richard T..

6 records

NASA NTRS1990

Installing scientific instruments into a cold LHe dewar - The Gravity Probe B approach

Gravity Probe B is an orbital test of Einstein's general theory of relativity using gyroscopes. The precession of the gyroscopes will measure both the geodetic effect (6.6 arcsec/yr) through the curved space-time surrounding the earth and the motional effect (0.042 arcsec/yr) due to the rotating earth dragging space-time around with it. To achieve the extraordinary accuracies needed to measure these small precessions, it is necessary to have the gyroscopes operating in the following environments: a vacuum of less than 10 exp -10 torr; an acceleration level of less than 10 exp -10 g's; a magnetic field of less than 10 exp -7 gauss; and a temperature near 2 K. This paper discusses designs that allow scientific instruments to be installed into a dewar at 4.2 K. Methods for structurally supporting the instruments, transferring heat across joints at low temperature in vacuum, and excluding air during the insertion process are discussed. The structural support method is designed for Shuttle launch loads.

Parmley, Richard T.↗

NASA NTRS1988

Design and test of a modified passive orbital disconnect strut (PODS-IV)

The design and testing of a modification to the Passive Orbital Disconnect Struts (PODS) III system (designed to reduce support conductance and superfluid-helium-tank dewar weights), PODS IV, are discussed. The PODS IV design was found to achieve a nominal increase of 630-812 percent in side-load resistance over the PODS-III design, with a predicted 15-percent increase in thermal conductance. It is noted that the increase in side-load resistance largely removes the limitation on length of the orbit tube inherent in the PODS III design. The higher resistance of the longer orbit tube results in lower total conductance for the PODS-IV design.

Spradley, Iran E.↗

NASA NTRS1988

Unique cryogenic features of the Gravity Probe B (GP-B) experiment

Cryogenic designs to simplify launch-pad operations for the Gravity Probe B experiment (an orbital test of Einsteins's general theory of relativity using gyroscopes) while achieving an orbital lifetime of two years are discussed. The proposed system allows the probe to be loaded into a cold dewar, provides good structural support and thermal contact after insertion, and eliminates the need for a pumping system during ground hold. The use of a gamma alumina/epoxy minimizes the parasitic heat loads into the dewar through the telescope aperture and the tank supports.

Parmley, Richard T.↗

NASA NTRS1987

Thermally Insulating Support for Cryogenic Tanks

Passive alternate-load-path support scheme keeps weight low while conserving cryogenic liquid. Method of supporting inner vessel of large Dewar container minimizes heat conductance and weight but ensures high strength and impact resistance. Accommodates thermal expansion and contraction of vessel while introducing minimal stresses in structure. Inner vessel hangs from struts in outer vessel. Thin wall graphite/epoxy tube protected from high loads by close tolerance stops.

Parmley, Richard T.↗

NASA NTRS1987

The prototype design of the Stanford Relativity Gyro Experiment

The Stanford Relativity Gyroscope Experiment constitutes a fundamental test of Einstein's General Theory of Relativity, probing such heretofore untested aspects of the theory as those that relate to spin by means of drag-free satellite-borne gyroscopes. General Relativity's prediction of two orthogonal precessions (motional and geodetic) for a perfect Newtonian gyroscope in polar orbit has not yet been experimentally assessed, and will mark a significant advancement in experimental gravitation. The technology employed in the experiment has been under development for 25 years at NASA's Marshall Space Flight Center. Four fused quartz gyroscopes will be used.

Parkinson, Bradford W.↗

NASA NTRS1986

System structural test results - Six PODS III supports

Passive orbital disconnect struts can potentially reduce the support conductance a factor of 10 over state-of-the-art tension band nondisconnect supports and cut helium dewar weights in half for the same lifetime. A series of thermal and structural tests were performed to verify that this performance improvement is real. Structural tests on a PODS-III support system (consisting of six struts) is reported here. The results show the predicted performance improvements can be achieved and the PODS-III supports are ready for flight applications. For large tankage systems requiring higher side load capability, a PODS-IV version is currently being developed.

Parmley, Richard T.↗