Search NASA⌕ Search

Engineering topics

Parrott, T. L.

Publications and source records attributed to Parrott, T. L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Investigation of an Anomaly Observed in Impedance Eduction Techniques

An intensive investigation into the cause of anomalous behavior commonly observed in impedance eduction techniques is performed. The investigation consists of grid refinement studies, detailed evaluation of results at and near anti-resonance frequencies, comparisons of different model results with synthesized and measured data, assessment or optimization techniques, and evaluation or boundary condition effects. Results show that the root cause of the anomalous behavior is the sensitivity of the educed impedance to small errors in the measured termination resistance at frequencies near anti-resonance or cut-on of a higher-order mode. Evidence is presented to show that the common usage of an anechoic, plane wave termination boundary condition in ducts where the "true" termination is reflective may act as a trigger for these anomalies. Replacing the exit impedance boundary condition by an exit pressure condition is shown to reduce the anomalous results.

Watson, W. R.↗
NASA NTRS2008

Uncertainty and Sensitivity Analyses of a Two-Parameter Impedance Prediction Model

This paper presents comparisons of predicted impedance uncertainty limits derived from Monte-Carlo-type simulations with a Two-Parameter (TP) impedance prediction model and measured impedance uncertainty limits based on multiple tests acquired in NASA Langley test rigs. These predicted and measured impedance uncertainty limits are used to evaluate the effects of simultaneous randomization of each input parameter for the impedance prediction and measurement processes. A sensitivity analysis is then used to further evaluate the TP prediction model by varying its input parameters on an individual basis. The variation imposed on the input parameters is based on measurements conducted with multiple tests in the NASA Langley normal incidence and grazing incidence impedance tubes; thus, the input parameters are assigned uncertainties commensurate with those of the measured data. These same measured data are used with the NASA Langley impedance measurement (eduction) processes to determine the corresponding measured impedance uncertainty limits, such that the predicted and measured impedance uncertainty limits (95% confidence intervals) can be compared. The measured reactance 95% confidence intervals encompass the corresponding predicted reactance confidence intervals over the frequency range of interest. The same is true for the confidence intervals of the measured and predicted resistance at near-resonance frequencies, but the predicted resistance confidence intervals are lower than the measured resistance confidence intervals (no overlap) at frequencies away from resonance. A sensitivity analysis indicates the discharge coefficient uncertainty is the major contributor to uncertainty in the predicted impedances for the perforate-over-honeycomb liner used in this study. This insight regarding the relative importance of each input parameter will be used to guide the design of experiments with test rigs currently being brought on-line at NASA Langley.

Jones, M. G.↗
NASA NTRS2006

Cascaded Perforates as One-Dimensional, Bulk Absorbers

Porous cell honeycomb liners for aircraft engine nacelles offer the possibility of exploiting extended reaction effects to improve liner attenuation bandwidth as generally attributed to the performance of bulk absorbers. This paper describes an analytical procedure, starting with an impedance prediction model for a single perforated plate, to estimate the bulk-absorber parameters for a cascade of such perforates - a first step to modeling a porous wall honeycomb structure. The objective is to build confidence in a lumped element impedance model, when applied to a uniformly-spaced set of porous plates to predict its .bulk. absorber properties. The model is based upon a modified version of the two-parameter flow resistance model of the form A + BV(sub inc), where A and B are physics-based, semi-empirical parameters that are adjusted to provide an optimum fit to a composite dataset from three plate porosities of 2.5, 5 and 10%. The composite dataset is achieved by reformulating the two-parameter flow resistance model into a .reduced pressure drop coefficient. dependency on perforate hole Reynolds number. The resulting impedance model is employed to calculate surface impedance spectra for N and 2N-layer perforate cascades. The well-known two-thickness method for experimental determination of bulk-absorber parameters is then applied to these .synthesized. data sets to predict the characteristic impedance and propagation constant for the perforate cascades. These results are then compared with experimental results reported in a companion paper.

Parrott, T. L.↗
NASA NTRS2005

A Quasi-3-D Theory for Impedance Eduction in Uniform Grazing Flow

A 2-D impedance eduction methodology is extended to quasi-3-D sound fields in uniform or shearing mean flow. We introduce a nonlocal, nonreflecting boundary condition to terminate the duct and then educe the impedance by minimizing an objective function. The introduction of a parallel, sparse, equation solver significantly reduces the wall clock time for educing the impedance when compared to that of the sequential band solver used in the 2-D methodology. The accuracy, efficiency, and robustness of the methodology is demonstrated using two examples. In the first example, we show that the method reproduces the known impedance of a ceramic tubular test liner. In the second example, we illustrate that the approach educes the impedance of a four-segment liner where the first, second, and fourth segments consist of a perforated face sheet bonded to honeycomb, and the third segment is a cut from the ceramic tubular test liner. The ability of the method to educe the impedances of multisegmented liners has the potential to significantly reduce the amount of time and cost required to determine the impedance of several uniform liners by allowing them to be placed in series in the test section and to educe the impedance of each segment using a single numerical experiment. Finally, we probe the objective function in great detail and show that it contains a single minimum. Thus, our objective function is ideal for use with local, inexpensive, gradient-based optimizers.

Watson, W. R.↗
NASA NTRS2003

A Computational and Experimental Study of Slit Resonators

Computational and experimental studies are carried out to offer validation of the results obtained from direct numerical simulation (DNS) of the flow and acoustic fields of slit resonators. The test cases include slits with 90-degree corners and slits with 45-degree bevel angle housed inside an acoustic impedance tube. Three slit widths are used. Six frequencies from 0.5 to 3.0 kHz are chosen. Good agreement is found between computed and measured reflection factors. In addition, incident sound waves having white noise spectrum and a prescribed pseudo-random noise spectrum are used in subsequent series of tests. The computed broadband results are again found to agree well with experimental data. It is believed the present results provide strong support that DNS can eventually be a useful and accurate prediction tool for liner aeroacoustics. The usage of DNS as a design tool is discussed and illustrated by a simple example.

Tam, C. K. W.↗
NASA NTRS2003

Comparison of Acoustic Impedance Eduction Techniques for Locally-Reacting Liners

Typical acoustic liners used in current aircraft inlets and aft-fan ducts consist of some type of perforated facesheet bonded to a honeycomb core. A number of techniques for determining the acoustic impedance of these locallyreacting liners have been developed over the last five decades. In addition, a number of models have been developed to predict the acoustic impedance of locallyreacting liners in the presence of grazing flow, and to use that information together with aeroacoustic propagation codes to assess the noise absorption provided by these liners. These prediction models have incorporated the results from databases acquired with specific impedance eduction techniques. Thus, while these prediction models are acceptable for liners that are similar to those tested in these databases, their application to new liner configurations must be viewed with caution. The primary purpose of this paper is to provide a comparison of impedance eduction techniques that have been implemented at various aerospace research laboratories in the United States (NASA Langley Research Center, General Electric Aircraft Engines, B. F. Goodrich and Boeing). A secondary purpose is to provide data for liner configurations that extend the porosity range beyond that which has been previously used in common aircraft engine nacelles. Two sets of liners were designed to study the effects of three parameters: perforate hole diameter, facesheet thickness and porosity. These two sets of liners were constructed for testing in each of the laboratories listed above. The first set of liners was designed to fit into the NASA Langley and Boeing test facilities. The second set was designed to fit into the General Electric Aircraft Engines and B. F. Goodrich test facilities. By using the same parent material, both sets of liners were identical to within the limits of material and fabrication variability. Baseline data were obtained in the normal incidence impedance tubes at NASA Langley and B. F. Goodrich. The results were found to compare extremely well. The samples were then tested in the grazing flow ducts of each of the four laboratories. Perhaps the most significant result of these comparisons is that the educed acoustic resistances for the liners used in this study increase as the mean flow profile is modified from uniform to 3-D shear. This realization has demonstrated the need for an frequency-dependent impedance eduction technique that incorporates 3-D shear flow and is efficient.

Jones, M. G.↗
NASA NTRS2002

A Method for Optimizing Non-Axisymmetric Liners for Multimodal Sound Sources

Central processor unit times and memory requirements for a commonly used solver are compared to that of a state-of-the-art, parallel, sparse solver. The sparse solver is then used in conjunction with three constrained optimization methodologies to assess the relative merits of non-axisymmetric versus axisymmetric liner concepts for improving liner acoustic suppression. This assessment is performed with a multimodal noise source (with equal mode amplitudes and phases) in a finite-length rectangular duct without flow. The sparse solver is found to reduce memory requirements by a factor of five and central processing time by a factor of eleven when compared with the commonly used solver. Results show that the optimum impedance of the uniform liner is dominated by the least attenuated mode, whose attenuation is maximized by the Cremer optimum impedance. An optimized, four-segmented liner with impedance segments in a checkerboard arrangement is found to be inferior to an optimized spanwise segmented liner. This optimized spanwise segmented liner is shown to attenuate substantially more sound than the optimized uniform liner and tends to be more effective at the higher frequencies. The most important result of this study is the discovery that when optimized, a spanwise segmented liner with two segments gives attenuations equal to or substantially greater than an optimized axially segmented liner with the same number of segments.

Watson, W. R.↗
NASA NTRS1986

Responses of a hot film and a pressure probe to acoustic excitation in mean flow

The responses of a hot film sensor and a pressure probe to acoustic excitation in steady flow up to a Mach number of 0.5 were measured and compared with the responses of a microphone, flush mounted in the wall of the flow duct. When compared in terms of fluctuating pressure, the response of the pressure probe was less than that of the wall microphone by about 2.1 dB or less at the 0.5 Mach number, while the response of the ho film probe was as much as 6.0 dB above that of the wall sensor, at the Mach numbers 0.3 and 0.5. In terms of fluctuating Reynolds number, the response of the hot film probe was greater than that of the wall-mounted sensor by at most 5.0 dB at the same Mach numbers. Removing the response contribution from fluctuating temperature in the hot film mathematical model improved the agreement between the two transducer responses for both comparisons.

Jones, M. G.↗
NASA NTRS1986

Pressure probe and hot-film probe rsponses to acoustic excitation in mean flow

An experiment was conducted to compare the relative responses of a hot-film probe and a pressure probe positioned in a flow duct carrying mean flow and progressive acoustic waves. The response of each probe was compared with that of a condenser-type microphone flush mounted in the duct wall for flow Mach numbers up to about 0.5. The response of the pressure probe was less than that of the flush-mounted microphone by not more than about 2.1 dB at the highest centerline Mach number. This decreased response of the probe can likely be attributed to flow-induced impedance changes at the probe sensor orifices. The response of the hot-film probe, expressed in terms of fluctuating pressure, was greater than that of the flush-mounted microphone by as much as 6.0 dB at the two higher centerline Mach numbers. Removal of the contribution from fluctuating temperature in the hot-film analytical model greatly improved the agreement between the two transducer responses.

Parrott, T. L.↗
NASA NTRS1986

Natural laminar flow flight experiments on a turbine engine nacelle fairing

Flight experiments are being conducted with the objective to investigate the interactions between acoustic disturbances and laminar flow in the flight environment. In the experiments, the laminar boundary layer on the nacelles will be exposed to discrete and broadband external noises, and the effect of varying noise levels and frequencies on the stability of the laminar flow will be studied. The present paper provides an overview of the complete project and a status report on the results which have been obtained. The flight experiment is conducted with the aid of a modified research aircraft. The phase I flight tests are concerned with a quick and simple determination of natural laminar flow (NLF) behavior on an engine nacelle. Attention is given to instrumentation, the acoustic noise source, flow visualization, and the test results.

Obara, C. J.↗
NASA NTRS1985

Analytical study of acoustic response of a semireverberant enclosure with application to active noise control

The acoustic response of a semireverberant enclosure with two interacting, velocity-prescribed source distributions was analyzed using standard modal analysis techniques with a view toward a better understanding of active noise control. Different source and enclosure dimensions, source separations, and single-wall admittances were studied over representative frequency bandwidths of 10 Hz with source relative phase as a parameter. Results indicate that power radiated into the enclosure agree qualitatively with the spatial average of the mean square pressure, even though the reverberant field is nondiffuse. Decreases in acoustic power can therefore be used to estimate global noise reduction in a nondiffuse semireverberant environment. As might be expected, parametric studies indicate that maximum power reductions of up to 25 dB can be achieved when secondary and primary sources are compact and closely spaced. Although less success is achieved with increasing frequency and source separation or size, significant suppression of up to 8 dB still occurs over the 1 to 2 Hz bandwidth.

Parrott, T. L.↗
NASA NTRS1983

Comparison of three methods for measuring acoustic properties of bulk materials

Three methods for measuring the acoustic properties of bulk materials have been evaluated. The methods differ from one another in their practical implementation and reliability. The two more convenient methods exploit changes in surface impedance of test samples resulting from a change in the test sample geometry or boundary conditions. The results from these surface methods are compared with that obtained using Scott's method. In Scott's method the propagation constant is obtained by a 'direct' measurement inside the test material by means of a probe tube. The comparisons suggest that the surface methods will provide reliable and accurate results when the test sample behaves as a rigid porous structure.

Smith, C. D.↗
NASA NTRS1983

The design and flight test of an engine inlet bulk acoustic liner

This paper summarizes the design, fabrication and flight evaluation of a Kevlar acoustic liner configuration for a JT15D turbofan engine. The liner was designed to suppress, by a measurable amount, a dominant (13,0) BPF tone. This tone or spinning mode was produced for research purposes by installing 41 circumferentially distributed small diameter rods upstream of the 28 fan blades. Duct liner attenuations calculated by a finite element procedure were compared to far field power (insertion) losses deduced from flight data. The finite element program modeled the variable geometry of the JT15D inlet and used a uniform flow with a boundary layer roll-off to model the inlet flow field. Calculated liner losses were generally conservative. That is, measured far field power losses were generally greater than attenuations calculated by the finite element computer program.

Lester, H. C.↗
NASA NTRS1983

Comparison of measured and calculated mode redistribution associated with spinning mode transmission through circumferentially segmented lined ducts

An experiment was conducted to investigate mode redistribution in lined circular ducts with circumferential impedance nonuniformities. Mode insertion losses were measured for six-segment, two-segment, and uniform liners in a spinning mode synthesizer (SMS) in the quiet flow facility in the Langley Aircraft Noise Reduction Laboratory and correlated with predicted transmission losses. Both experiment and theory show that circumferentially segmented duct liners do scatter energy into circumferential modes of different orders. Good agreement measured and calculated attenuations was obtained for circumferential mode numbers paired with zero order radial mode numbers. For the higher order radials, the agreement was not as good.

Parrott, T. L.↗
NASA NTRS1980

Calculated and measured performance of a 'near ideal' locally reacting duct liner in grazing incidence

The calculated acoustic response of a nearly ideal (locally reacting and linear) duct liner has been compared with its measured performance. The ceramic honeycomb liner structure was such that the local reaction assumption was well satisfied over the frequency range of interest (0.5-3.0 kHz). In addition, the high repeatability of the measured impedance values over a large SPL range verified the assumption of linearity. A finite element algorithm was used to compute the duct liner transmission properties in terms of the liner's normal incidence impedance and the duct termination impedance using a plane wave source. Very good agreement between theory and experiment was observed in general, but required accurate normal impedance values in the high attenuation frequency bands of the liner's response.

Parrott, T. L.↗
NASA NTRS1979

Application of a finite element method for computing grazing incidence wave structure in an impedance tube - Comparison with experiment

The acoustic performance of a liner specimen, in a grazing incidence impedance tube, is analyzed using a finite element method. The liner specimen was designed to be a locally reacting, two-degree-of-freedom type with the resistance and reactance provided by perforated facesheets and compartmented cavities. Measured and calculated wave structures are compared for both normal and grazing incidence from 0.3 to 1.2 kHz. A finite element algorithm was incorporated into an optimization loop in order to predict liner grazing incidence impedance from measured SWR and null position data. Results suggest that extended reaction effects may have been responsible for differences between normal and grazing incidence impedance estimates.

Lester, H. C.↗
NASA NTRS1978

Impedance measurement using a two-microphone, random-excitation method

The feasibility of using a two-microphone, random-excitation technique for the measurement of acoustic impedance was studied. Equations were developed, including the effect of mean flow, which show that acoustic impedance is related to the pressure ratio and phase difference between two points in a duct carrying plane waves only. The impedances of a honeycomb ceramic specimen and a Helmholtz resonator were measured and compared with impedances obtained using the conventional standing-wave method. Agreement between the two methods was generally good. A sensitivity analysis was performed to pinpoint possible error sources and recommendations were made for future study. The two-microphone approach evaluated in this study appears to have some advantages over other impedance measuring techniques.

Seybert, A. F.↗