Asymmetric gas diffusion layers for improved water management in PGM-free electrodes
Not Available
25 ENERGY STORAGE↗
Engineering topics
Pasaogullari, Ugur
Publications and source records attributed to Pasaogullari, Ugur.
Self-Sacrificial Template Synthesis of Fe-N-C Catalysts with Dense Active Sites Deposited on A Porous Carbon Network for High Performance in PEMFC
In this study, iron-nitrogen-carbon (Fe-N-C) single-atom catalysts are promising sustainable alternatives to the costly and scarce platinum (Pt) to catalyze the oxygen reduction reactions (ORR) at the cathode of proton exchange membrane fuel cells (PEMFCs). However, Fe-N-C cathodes for PEMFC are made thicker than Pt/C ones, in order to compensate for the lower intrinsic ORR activity and site density of Fe-N-C materials. The thick electrodes are bound with mass transport issues that limit their performance at high current densities, especially in H 2 /air PEMFCs. Practical Fe-N-C electrodes must combine high intrinsic ORR activity, high site density, and fast mass transport. Herein, it has achieved an improved combination of these properties with a Fe-N-C catalyst prepared via a two-step synthesis approach, constructing first a porous zinc-nitrogen-carbon (Zn-N-C) substrate, followed by transmetallating Zn by Fe via chemical vapor deposition. A cathode comprising this Fe-N-C catalyst has exhibited a maximum power density of 0.53 W cm -2 in H 2 /air PEMFC at 80 °C. The improved power density is associated with the hierarchical porosity of the Zn-N-C substrate of this work, which is achieved by epitaxial growth of ZIF-8 onto g-C 3 N 4 , leading to a micro-mesoporous substrate.
25 ENERGY STORAGE↗
AMES: MS and MENG in Advanced Manufacturing for Energy at the University of Connecticut (Final Technical Report)
The objective of the project is to develop and implement an advanced degree program (MS and MENG in Advanced Manufacturing for Energy Systems, AMES) responding to the long-term workforce and technology requirements of the nation’s advanced energy products manufacturing industry. The program provided an industry relevant research experience by leveraging existing energy (e.g. fuels, power electronics, electrochemical power sources) and advanced manufacturing (e.g. additive manufacturing, composites, sensing) research at UConn funded by federal and state agencies, and industry, as well as through our industry partnerships. The trainees have joined research teams, advised by faculty with relevant research interests and expertise and were co-advised by industrial mentors. The AMES program have developed a truly interdisciplinary curriculum, first graduate degree program at UConn School (now College) of Engineering not housed in an academic department, with concentrations focusing on various challenges in advanced manufacturing for energy systems, e.g. advanced materials and processing. The project also developed new courses focusing on common technical and professional skills, and integrated various components for an industry relevant training. The program has admitted 29 Master of Science (MS) students since inception in January 2019. Twenty six of these students were AMES fellows, who have received partial funding from DoE through this project. The program far exceeded the goal of admitting at least five new MS (with thesis) students. All students were required to complete a thesis (M.S.) or a capstone (M.Eng.) project that are defined in collaboration with industry partners to ensure industrial relevancy, addressing a current industrial challenges. Industrial mentors also participated in advising the students in their research. AMES fellows, in addition were also required to complete an industrial internship for further industrial experience.
36 MATERIALS SCIENCE↗
A Goldilocks Approach to Water Management: Hydrochannel Porous Transport Layers for Unitized Reversible Fuel Cells
Abstract This work presents a novel porous transport layer (PTL), the hydrochannel PTL, that enables improved water management and record high round trip efficiency in unitized reversible fuel cells (URFCs). URFCs require rapid transport of O 2 and H 2 O to provide high performance in both fuel cell and water electrolyzer operation, but cell design is complicated by conflicting water management requirements: electrolyzers perform best with high liquid water saturation, whereas fuel cells perform best when liquid water saturation is as low as possible while still maintaining effective ionomer hydration. The hydrochannel PTL circumvents this obstacle by providing hydrophilic channels for water transport through an otherwise hydrophobic PTL, enabling optimal performance in both fuel cell and water electrolyzer modes. Neutron radiography measurements of water content in both operating modes confirm that the hydrochannel PTL enables high performance due to its improved water management capabilities.
25 ENERGY STORAGE↗
Simulation of 12-bed vacuum pressure-swing adsorption for hydrogen separation from methanol-steam reforming off-gas
This study focuses on analysis of a 12-bed vacuum pressure-swing adsorption (VPSA) process capable of purifying hydrogen from a ternary mixture (H 2 /CO 2 /CO 75/24/1 mol%) derived from methanol-steam reforming. The process produces 9 kmol H 2 /h with less than 2 ppm and 0.2 ppm of CO2 and CO, respectively, to supply a polymer electrolyte membrane fuel cell. The process model is developed in Aspen Adsorption® using the “uni-bed” approach. A parametric study of H 2 purity and recovery with respect to adsorption pressure, adsorbent height, activated carbon:zeolite ratio, feed composition, and number of beds is performed. Results show 12-bed VPSA can meet the H 2 purity goals, with H 2 recovery as high as 75.75%. Adsorption occurs at 7 bar, the column height is 1.2 m, and the adsorbent ratio is 70%:30%. Furthermore, a 4-bed VPSA can achieve the same purity goals as the 12-bed process, but H 2 recovery decreases to 61.34%.
03 NATURAL GAS↗
Manufacturing Process of Electrode Films
Rotating disk electrode (RDE) experiments form a key experimental characterization technique for measuring electrocatalyst performance and durability. While standard RDE testing protocols have been documented, it has been noted that catalyst film quality can skew measurements. Furthermore, the impact of relative humidity on drying is studied in an effort to produce consistent, high quality catalyst films for RDE experiments, which shows that high quality catalyst films can be manufactured repeatedly in a controlled environment, such as inside an environmental chamber as described.
08 HYDROGEN↗