Engineering topics

Patel, D.

Publications and source records attributed to Patel, D..

At least 19 records

DOE OSTI2024

Mitigation of hot-electron preheat from the two-plasmon-decay instability using silicon-doped plastic shells in direct-drive implosions on OMEGA

Hot electrons generated by the two-plasmon-decay (TPD) instability in laser-direct-drive implosions preheat the fuel and degrade performance. The mitigation of preheat using silicon-doped ablators (i.e., preheat is reduced by a factor of 1.40 ± 0.04) while decreasing the ratio of the laser spot diameter to the target diameter (⁠R b /R t⁠ ) to mitigate cross-beam energy transfer has been demonstrated on the OMEGA laser for quarter-critical laser intensities of 4.1 x 10 14 W/cm 2 ⁠, equivalent to an incident laser intensity of 8.3 x 10 14 W/cm 2 ⁠. The silicon dopant increases the electron temperature of the ablation plasma, which raises the intensity threshold for the onset of the TPD instability. These results show that implosion designs utilizing higher drive intensities can be used to achieve higher shell velocities, which are currently inaccessible with plastic ablators due to excessive preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Applications of a Rayleigh-Taylor model to direct-drive laser fusion

Here, this paper presents a simple physics-based model for the interpretation of key metrics in laser direct drive. The only input parameters required are target scale, in-flight aspect ratio, and beam-to-target radius, and the importance of each has been quantified with a tailored set of cryogenic implosion experiments. These analyses lead to compact and accurate predictions of the fusion yield and areal density as a function of hydrodynamic stability, and suggest new ways to take advantage of direct drive. To provide examples, we will discuss how the inferred mix width behaves relative to theory, then show how it could be exploited to perform a direct drive implosion with a Lawson metric or Χ no α of 0.24 ± 0.02—using a novel parameter space at high velocities and beam radii on the OMEGA laser—that projects to ignition at a laser energy ≤2.0 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Persistent Hot-Spot Mix in Cryogenic Direct-Drive Fusion Experiments

We show that an x-ray emission signature associated with acceleration phase mass injection correlates with poor experimental hot-spot convergence and a reduced neutron production relative to expectations. It is shown that with increased target mass as well as with higher-design adiabats, this signature is reduced, whereas with increased debris on the target the signature is increased. Here, we estimate that the vapor region in typical best designs may have up to 2x the assumed hydrogen mass at the start of deceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Demonstration of a hydrodynamically equivalent burning plasma in direct-drive inertial confinement fusion

Focussing laser light onto the surface of a small target filled with deuterium and tritium implodes it and leads to the creation of a hot and dense plasma, in which thermonuclear fusion reactions occur. In order for the plasma to become self-sustaining, the heating of the plasma must be dominated by the energy provided by the fusion reactions—a condition known as a burning plasma. A metric for this is the generalized Lawson parameter, where values above around 0.8 imply a burning plasma. Here, we report on hydro-equivalent scaling of experimental results on the OMEGA laser system and show that these have achieved core conditions that reach a burning plasma when the central part of the plasma, the hotspot, is scaled in size by at least a factor of 3.9 ± 0.10, which would require a driver laser energy of at least 1.7 ± 0.13 MJ. In addition, we hydro-equivalently scale the results to the 2.15 MJ of laser energy available at the National Ignition Facility and find that these implosions reach 86% of the Lawson parameter required for ignition. Furthermore, our results support direct-drive inertial confinement fusion as a credible approach for achieving thermonuclear ignition and net energy in laser fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Measuring higher-order moments of neutron-time-of-flight data for cryogenic inertial confinement fusion implosions on OMEGA

Ion temperatures serve as an important diagnostic for inertial confinement fusion (ICF) implosions. In direct-drive ICF experiments on OMEGA, neutron-time-of-flight (nTOF) data are used to infer the ion temperature of the fusing plasma produced in the implosion experiment. The analysis of the nTOF data requires an assumption about the shape of the underlying source signal. Since the source nTOF signal is a near-replica of the neutron energy spectrum, an ideal Gaussian shape, corresponding to the neutron energy spectrum of a uniform temperature plasma, is routinely employed. However, spatial and temporal variations of the ion temperature in the plasma give rise to higher-order moments, which were first described by Munro [Nucl. Fusion 56, 036001 (2016)]. In this work, we show a simpler alternative analysis to derive moments of the neutron energy spectrum for a plasma with variations in ion temperature. We also present a revised analysis of measured nTOF signals that uses a model with an additional degree of freedom to take into account the effect of ion temperature variations on the shape of the spectrum. Compared to presently used nTOF analysis, the revised analysis yields on average ≈2× more accurate fits to the data and up to 15% higher ion temperatures for cryogenic experiments. As a result, we quantify the ion temperature inflation caused by radially symmetric fluid flows, which are present even in a symmetric implosion, and which serve as a lower bound on the ion temperature inflation in real implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Diagnosing low-mode (ℓ < 6) and mid-mode (6 ≤ ℓ ≤ 60) asymmetries in the post-stagnation phase of laser-direct-drive deuterium–tritium cryogenic implosions on OMEGA

Low- and mid-mode perturbations are possible candidates for performance limitations in cryogenic direct-drive implosions on the OMEGA laser at the Laboratory of Laser Energetics. Simulations with a 3D hydrocode demonstrated that hotspot imagers do not show evidence of the shell breakup in the dense fuel. However, these same simulations revealed that the low- and mid-mode perturbations in the dense fuel could be diagnosed more easily in the post-stagnation phase of the implosion by analyzing the peak in the x-ray emission limb at the coronal–fuel interface than before or at the stagnation phase. In experiments, the asymmetries are inferred from gated images of the x-ray emission of the implosion by using a 16-pinhole array imager filtered to record x-ray energies >800 eV and an x-ray framing camera with 40-ps time integration and 20-μm spatial resolution. Furthermore, a modal analysis is applied to the spatial distribution of the x-ray emission from deuterium and tritium cryogenic implosions on OMEGA recorded after the bang time to diagnose the low- and mid-mode asymmetries, and to study the effect that the beam-to-target ratio (Rb/Rt) has on the shell integrity.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Inferences of hot electron preheat and its spatial distribution in OMEGA direct drive implosions

Hot electrons generated from laser plasma instabilities degrade performance of direct drive implosions by preheating the deuterium and tritium (DT) fuel resulting in early decompression and lower areal densities at stagnation. A technique to quantify the hot electron preheat of the dense DT fuel and connect it to the degradation in areal density is described in detail. Hot electrons are measured primarily from the hard x-rays they emit as they slow down in the target. The DT preheat is inferred from a comparison of the hard x-ray signals between a DT-layered implosion and its mass equivalent ablator only implosion. The preheat energy spatial distribution within the imploding shell is inferred from experiments using high Z payloads of varying thicknesses. It is found that the electrons deposit their energy uniformly throughout the shell material. For typical direct-drive OMEGA implosions driven with an overlapped intensity of ∼9·1014 W/cm2, approximately ∼0.02%–0.03% of the laser energy is converted into preheat of the stagnated fuel which corresponds to areal density degradations of 10%–20%. The degradations in areal density explain some of the observed discrepancies between the simulated and measured areal densities.

Christopherson, A. R. (ORCID:000000033578635X)↗

DOE OSTI2022

Predicting hot electron generation in inertial confinement fusion with particle-in-cell simulations

A series of two-dimensional particle-in-cell simulations with speckled laser drivers was carried out to study hot electron generation in direct-drive inertial confinement fusion on OMEGA. Scaling laws were obtained for hot electron fraction and temperature as functions of laser/plasma conditions in the quarter-critical region. Using these scalings and conditions from hydro simulations, the temporal history of hot electron generation can be predicted. The scalings can be further improved to predict hard x-rays for a collection of OMEGA warm target implosions within experimental error bars. Furthermore, these scalings can be readily implemented into inertial confinement fusion design codes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Analysis of core asymmetries in inertial confinement fusion implosions using three-dimensional hot-spot reconstruction

Three-dimensional effects play a crucial role during the hot-spot formation in inertial confinement fusion (ICF) implosions. A data analysis technique for 3D hot-spot reconstruction from experimental observables has been developed to characterize the effects of low modes on 3D hot-spot formations. In nuclear measurements, the effective flow direction, governed by the maximum eigenvalue in the velocity variance of apparent ion temperatures, has been found to agree with the measured hot-spot flows for implosions dominated by mode ℓ = 1. Asymmetries in areal-density (ρR) measurements were found to be characterized by a unique cosine variation along the hot-spot flow axis. In x-ray images, a 3D hot-spot x-ray emission tomography method was developed to reconstruct the 3D hot-spot plasma emissivity using a generalized spherical-harmonic Gaussian function. The gradient-descent algorithm was used to optimize the mapping between the projections from the 3D hot-spot emission model and the measured x-ray images along multiple views. Furthermore, this work establishes a platform to analyze 3D low-mode core asymmetries in ICF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Bound on hot-spot mix in high-velocity, high-adiabat direct-drive cryogenic implosions based on comparison of absolute x-ray and neutron yields

In laser-driven implosions for laboratory fusion, the comparison of hot-spot x-ray yield to neutron production can serve to infer hot-spot mix. For high-performance direct-drive implosions, this ratio depends sensitively on the degree of equilibration between the ion and electron fluids. A scaling for x-ray yield as a function of neutron yield and characteristic ion and electron hot-spot temperatures is developed on the basis of simulations with varying degrees of equilibration. We apply this model to hot-spot x-ray measurements of direct-drive cryogenic implosions typical of the direct-drive designs with best ignition metrics. Furthermore, the comparison of the measured x-ray and neutron yields indicates that hot-spot mix, if present, is below a sensitivity estimated as ~ 2% by-atom mix of ablator plastic into the hot spot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Enhanced Laser–Energy Coupling with Small-Spot Distributed Phase Plates (SG5-650) in OMEGA DT Cryogenic Target Implosions

Cryogenic deuterium–tritium ice target implosions on OMEGA with new small-spot ("SG5-650") distributed phase plates (DPP's) achieved an (11 +/- 4)% increase in energy coupling compared to implosions with standard-spot DPP's by decreasing the ratio of the laser spot diameter to the target diameter from 0.93 to 0.75. The SG5-650 DPP's provide a focus spot size of 674 um, which is defined as the diameter that encircles 95% of the measured beam energy compared to 834 um for the SG5-850. The hydrodynamic effciency, defined as the ratio of the kinetic energy in the imploding shell to the laser energy, increased from 4.5% to 5.0% based on radiation-hydrodynamic calculations benchmarked to shell trajectory and bang-time measurements. The higher coupling came with a trade-off of an increased hot-electron production as well as increased hydrodynamic instabilities seeded by a larger mode-10 amplitude from the beam port geometry, both of which may have affected the fusion neutron production and areal density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Direct Measurements of DT Fuel Preheat from Hot Electrons in Direct-Drive Inertial Confinement Fusion

Hot electrons generated by laser-plasma instabilities degrade the performance of laser-fusion implosions by preheating the DT fuel and reducing core compression. The hot-electron energy deposition in the DT fuel has been directly measured for the first time by comparing the hard x-ray signals between DT-layered and mass-equivalent ablator-only implosions. The electron energy deposition profile in the fuel is inferred through dedicated experiments using Cu-doped payloads of varying thickness. The measured preheat energy accurately explains the areal-density degradation observed in many OMEGA implosions. This technique can be used to assess the viability of the direct-drive approach to laser fusion with respect to the scaling of hot-electron preheat with laser energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Enhanced laser-energy coupling with small-spot distributed phase plates (SG5-650) in OMEGA DT cryogenic target implosions

Cryogenic deuterium–tritium ice target implosions on OMEGA with new small-spot (SG5-650) distributed phase plates (DPPs) achieved an (11 ± 4)% increase in energy coupling compared to implosions with larger-spot SG5-850 DPPs by decreasing the ratio of the laser spot diameter to the target diameter from 0.93 to 0.75. The SG5-650 DPPs provide a focus spot size of 674 μm, which is defined as the diameter that encircles 95% of the measured beam energy compared to 834 μm for the SG5-850, which are the standard DPPs in cryogenic target implosions on OMEGA. The hydrodynamic efficiency, defined as the ratio of the kinetic energy in the imploding shell to the laser energy, increased from 4.5% to 5.0% based on radiation-hydrodynamic calculations benchmarked to shell trajectory and bang-time measurements. Furthermore, the higher coupling came with a trade-off of an increased hot-electron production as well as increased hydrodynamic instabilities seeded by a larger mode-10 amplitude from the beam port geometry, both of which may have reduced the fusion neutron production and areal density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Using statistical modeling to predict and understand fusion experiments

Over 300 cryogenic layered direct-drive inertial confinement fusion implosions have been successfully executed on the OMEGA Laser System in the last decade. However, extracting sufficient understanding from these experiments to develop new designs or to identify or mitigate degradation sources remains challenging. Recently, a statistical modeling approach was developed to successfully design and predict improved implosion experiments on OMEGA. Here, we show that one-dimensional simulations can be used to predict the outcomes of systematically perturbed three-dimensional simulations and that this statistical modeling approach can be used to identify or rule out physical mechanisms for some of the degradation sources observed on the OMEGA Laser System for direct-drive cryogenic inertial confinement fusion. In this instance, we investigate the fusion yield dependencies on the ion temperature asymmetries and laser beam size observed in experiments by comparing with trends in three-dimensional synthetic simulation databases. Using the statistical model on these systematically perturbed simulations, we find that the statistically inferred dependency on the measured ion temperature asymmetries is well explained by imposed ℓ =1 modes. However, we find that the dependency on the laser beam size is only dominated by the illumination non-uniformity for some extreme cases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Experimentally Inferred Fusion Yield Dependencies of OMEGA Inertial Confinement Fusion Implosions

Statistical modeling of experimental and simulation databases has enabled the development of an accurate predictive capability for deuterium-tritium layered cryogenic implosions at the OMEGA laser. Here, a physics-based statistical mapping framework is described and used to uncover the dependencies of the fusion yield. This model is used to identify and quantify the degradation mechanisms of the fusion yield in direct-drive implosions on OMEGA. The yield is found to be reduced by the ratio of laser beam to target radius, the asymmetry in inferred ion temperatures from the $l$ = 1 mode, the time span over which tritium fuel has decayed, and parameters related to the implosion hydrodynamic stability. When adjusted for tritium decay and $l$ = 1 mode, the highest yield in OMEGA cryogenic implosions is predicted to exceed 2 × 10 14 fusion reactions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Direct Measurements of DT Fuel Preheat from Hot Electrons in Direct-Drive Inertial Confinement Fusion

Hot electrons generated by laser-plasma instabilities degrade the performance of laser-fusion implosions by preheating the DT fuel and reducing core compression. The hot-electron energy deposition in the DT fuel has been directly measured for the first time by comparing the hard x-ray signals between DT-layered and mass-equivalent ablator-only implosions. The electron energy deposition profile in the fuel is inferred through dedicated experiments using Cu-doped payloads of varying thickness. The measured preheat energy accurately explains the areal-density degradation observed in many OMEGA implosions. Furthermore, this technique can be used to assess the viability of the direct-drive approach to laser fusion with respect to the scaling of hot-electron preheat with laser energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Mitigation of mode-one asymmetry in laser-direct-drive inertial confinement fusion implosions

Nonuniformities present in the laser illumination and target in laser-driven inertial confinement fusion experiments lead to an asymmetric compression of the target, resulting in an inefficient conversion of shell kinetic energy to thermal energy of the hot-spot plasma. In this paper, the effects of asymmetric compression of cryogenic deuterium tritium laser-direct-drive implosions are examined using a suite of nuclear and x-ray diagnostics on the OMEGA laser. The neutron-averaged hot-spot velocity (~uhs) and apparent ion temperature (Ti) asymmetry are determined from neutron time-of-flight measurements of the primary deuterium tritium fusion neutron energy spectrum, while the areal density (rhoR) of the compressed fuel surrounding the hot spot is inferred from measurements of the scattered neutron energy spectrum. The low-mode perturbations of the hot-spot shape are characterized from x-ray self-emission images recorded along three quasi-orthogonal lines of sight. Implosions with significant mode-1 laser drive asymmetries show large hot-spot velocities (>100 km/s) in a direction consistent with the hot-spot elongation observed in x-ray images, measured Ti asymmetry, and rhoR asymmetry. Laser drive corrections have been applied through shifting the initial target location in order to mitigate the observed asymmetry. With the asymmetry corrected, a more-symmetric hot spot is observed with reduced ~uhs, Ti asymmetry, rhoR asymmetry, and a 30% increase in the fusion yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Mitigation of mode-one asymmetry in laser-direct-drive inertial confinement fusion implosions

Nonuniformities present in the laser illumination and target in laser-driven inertial confinement fusion experiments lead to an asymmetric compression of the target, resulting in an inefficient conversion of shell kinetic energy to thermal energy of the hot-spot plasma. In this paper, the effects of asymmetric compression of cryogenic deuterium tritium laser-direct-drive implosions are examined using a suite of nuclear and x-ray diagnostics on the OMEGA laser. The neutron-averaged hot-spot velocity (u → hs ) and apparent ion temperature (T i ) asymmetry are determined from neutron time-of-flight measurements of the primary deuterium tritium fusion neutron energy spectrum, while the areal density (ρR) of the compressed fuel surrounding the hot spot is inferred from measurements of the scattered neutron energy spectrum. Here, the low-mode perturbations of the hot-spot shape are characterized from x-ray self-emission images recorded along three quasi-orthogonal lines of sight. Implosions with significant mode-1 laser drive asymmetries show large hot-spot velocities (>100 km/s) in a direction consistent with the hot-spot elongation observed in x-ray images, measured T i asymmetry, and ρR asymmetry. Laser drive corrections have been applied through shifting the initial target location in order to mitigate the observed asymmetry. With the asymmetry corrected, a more-symmetric hot spot is observed with reduced u → hs , T i asymmetry, ρR asymmetry, and a 30% increase in the fusion yield.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗