Engineering topics

Patnaik, S. N.

Publications and source records attributed to Patnaik, S. N..

10 records

NASA NTRS1994

Structural optimization with approximate sensitivities

Computational efficiency in structural optimization can be enhanced if the intensive computations associated with the calculation of the sensitivities, that is, gradients of the behavior constraints, are reduced. Approximation to gradients of the behavior constraints that can be generated with small amount of numerical calculations is proposed. Structural optimization with these approximate sensitivities produced correct optimum solution. Approximate gradients performed well for different nonlinear programming methods, such as the sequence of unconstrained minimization technique, method of feasible directions, sequence of quadratic programming, and sequence of linear programming. Structural optimization with approximate gradients can reduce by one third the CPU time that would otherwise be required to solve the problem with explicit closed-form gradients. The proposed gradient approximation shows potential to reduce intensive computation that has been associated with traditional structural optimization.

Patnaik, S. N.↗

NASA NTRS1993

Preliminary analysis and design optimization of the short spacer truss of Space Station Freedom

The analysis, dynamic simulation, and design optimization of the short spacer truss of the Space Station Freedom are presented in this report. The short spacer truss will be positioned between the integrated equipment assembly (IEA) and another truss, called the long spacer truss, in the Space Station Freedom. During its launch in the Space Shuttle, the truss will be subjected to considerable in-span distributed inertia loads due to shuttle accelerations. The short spacer truss, therefore, has been modeled as a space frame to account for flexural response. Several parameters have been assumed, since the design specifications are in the process of development; hence the results presented should be considered preliminary. However, the automated analysis and design capabilities that have been developed can readily be used to generate an optimum design of the short spacer truss once the actual specifications have been determined. This report includes static and dynamic analyses of the short spacer truss, which have been obtained with the linear elastic code LE-HOST (in these analyses, LE-HOST data files have been automated to facilitate their future use for different design specifications of the short spacer truss); the dynamic animation of the short spacer truss, which has been carried out by using the results of the dynamic analysis and a post-processing feature of the modeling code PATRAN; and the optimum-weight design of the spacer truss, which was obtained under prescribed stress, displacement, and frequency constraints by using the design code COMETBOARDS. Examination of the analysis and design results revealed that the design could be improved if the configuration of the short spacer truss were modified to a certain extent. A modified configuration, which may simplify fabrication, has been suggested. The performance of this configuration has been evaluated and was found to be satisfactory under both static and dynamic conditions.

Gendy, A. S.↗

NASA NTRS1993

Singularity in structural optimization

The conditions under which global and local singularities may arise in structural optimization are examined. Examples of these singularities are presented, and a framework is given within which the singularities can be recognized. It is shown, in particular, that singularities can be identified through the analysis of stress-displacement relations together with compatibility conditions or the displacement-stress relations derived by the integrated force method of structural analysis. Methods of eliminating the effects of singularities are suggested and illustrated numerically.

Patnaik, S. N.↗

NASA NTRS1993

Optimum Design of Aerospace Structural Components Using Neural Networks

The application of artificial neural networks to capture structural design expertise is demonstrated. The principal advantage of a trained neural network is that it requires a trivial computational effort to produce an acceptable new design. For the class of problems addressed, the development of a conventional expert system would be extremely difficult. In the present effort, a structural optimization code with multiple nonlinear programming algorithms and an artificial neural network code NETS were used. A set of optimum designs for a ring and two aircraft wings for static and dynamic constraints were generated using the optimization codes. The optimum design data were processed to obtain input and output pairs, which were used to develop a trained artificial neural network using the code NETS. Optimum designs for new design conditions were predicted using the trained network. Neural net prediction of optimum designs was found to be satisfactory for the majority of the output design parameters. However, results from the present study indicate that caution must be exercised to ensure that all design variables are within selected error bounds.

Berke, L.↗

NASA NTRS1992

Improved accuracy for finite element structural analysis via an integrated force method

A comparative study was carried out to determine the accuracy of finite element analyses based on the stiffness method, a mixed method, and the new integrated force and dual integrated force methods. The numerical results were obtained with the following software: MSC/NASTRAN and ASKA for the stiffness method; an MHOST implementation method for the mixed method; and GIFT for the integrated force methods. The results indicate that on an overall basis, the stiffness and mixed methods present some limitations. The stiffness method generally requires a large number of elements in the model to achieve acceptable accuracy. The MHOST method tends to achieve a higher degree of accuracy for course models than does the stiffness method implemented by MSC/NASTRAN and ASKA. The two integrated force methods, which bestow simultaneous emphasis on stress equilibrium and strain compatibility, yield accurate solutions with fewer elements in a model. The full potential of these new integrated force methods remains largely unexploited, and they hold the promise of spawning new finite element structural analysis tools.

Patnaik, S. N.↗

NASA NTRS1992

Singularities in optimal structural design

Singularity conditions that arise during structural optimization can seriously degrade the performance of the optimizer. The singularities are intrinsic to the formulation of the structural optimization problem and are not associated with the method of analysis. Certain conditions that give rise to singularities have been identified in earlier papers, encompassing the entire structure. Further examination revealed more complex sets of conditions in which singularities occur. Some of these singularities are local in nature, being associated with only a segment of the structure. Moreover, the likelihood that one of these local singularities may arise during an optimization procedure can be much greater than that of the global singularity identified earlier. Examples are provided of these additional forms of singularities. A framework is also given in which these singularities can be recognized. In particular, the singularities can be identified by examination of the stress displacement relations along with the compatibility conditions and/or the displacement stress relations derived in the integrated force method of structural analysis.

Patnaik, S. N.↗

NASA NTRS1992

Singularities in Optimal Structural Design

Patnaik, S. N.↗

NASA NTRS1991

Compatibility conditions of structural mechanics for finite element analysis

The equilibrium equations and the compatibility conditions are fundamental to the analyses of structures. However, anyone who undertakes even a cursory generic study of the compatibility conditions can discover, with little effort, that historically this facet of structural mechanics had not been adequately researched by the profession. Now the compatibility conditions (CC's) have been researched and are understood to a great extent. For finite element discretizations, the CC's are banded and can be divided into three distinct categories: (1) the interface CC's; (2) the cluster or field CC's; and (3) the external CC's. The generation of CC's requires the separating of a local region, then writing the deformation displacement relation (ddr) for the region, and finally, the eliminating of the displacements from the ddr. The procedure to generate all three types of CC's is presented and illustrated through examples of finite element models. The uniqueness of the CC's thus generated is shown.

Patnaik, S. N.↗

NASA NTRS1991

Integrated force method versus displacement method for finite element analysis

A novel formulation termed the integrated force method (IFM) has been developed in recent years for analyzing structures. In this method all the internal forces are taken as independent variables, and the system equilibrium equations (EEs) are integrated with the global compatibility conditions (CCs) to form the governing set of equations. In IFM the CCs are obtained from the strain formulation of St. Venant, and no choices of redundant load systems have to be made, in constrast to the standard force method (SFM). This property of IFM allows the generation of the governing equation to be automated straightforwardly, as it is in the popular stiffness method (SM). In this report IFM and SM are compared relative to the structure of their respective equations, their conditioning, required solution methods, overall computational requirements, and convergence properties as these factors influence the accuracy of the results. Overall, this new version of the force method produces more accurate results than the stiffness method for comparable computational cost.

Patnaik, S. N.↗

NASA NTRS1990

General purpose program to generate compatibility matrix for the integrated force method

An efficient procedure for obtaining the compatibility conditions of finite-element models involves the generation of both field and compatibility conditions from deformation-displacement relations, using (1) the compatibility bandwidth, and (2) the node-determinacy concept. A computer program thus structured will generate sparse and banded compatibility conditions for a structure that is idealized by the finite elements.

Nagabhusanam, J.↗