Engineering topics

Patterson, James C., Jr.

Publications and source records attributed to Patterson, James C., Jr..

11 records

NASA NTRS1993

Underwing compression vortex attenuation device

A vortex attenuation device is presented which dissipates a lift-induced vortex generated by a lifting aircraft wing. The device consists of a positive pressure gradient producing means in the form of a compression panel attached to the lower surface of the wing and facing perpendicular to the airflow across the wing. The panel is located between the midpoint of the local wing cord and the trailing edge in the chord-wise direction and at a point which is approximately 55 percent of the wing span as measured from the fuselage center line in the spanwise direction. When deployed in flight, this panel produces a positive pressure gradient aligned with the final roll-up of the total vortex system which interrupts the axial flow in the vortex core and causes the vortex to collapse.

Patterson, James C., Jr.↗

NASA NTRS1991

Flight test to determine feasibility of a proposed airborne wake vortex detection concept

This investigation was conducted to determine the radial extent at which aircraft mounted flow vanes or roll rate gyros can sense the circulatory flow field that exists around the lift induced vortex system generated by an aircraft in flight. The probe aircraft was equipped with wingtip sensors for measuring angle of attack and angle of sideslip, and with a fuselage mounted gyroscope for measuring roll rate. Analysis of flight test data indicated that the vortex was detectable at a lateral distance of about 105 feet (best results) using unsophisticated equipment. Measurements were made from the centerline of the probe aircraft to the center of the nearest vortex with the probe aircraft flying between one half and one and one half miles behind the vortex generating aircraft.

Branstetter, James R.↗

NASA NTRS1990

Effect of location of aft-mounted nacelles on the longitudinal aerodynamic characteristics of a high-wing transport airplane

As part of a propulsion/airframe integration program at Langley Research Center, tests were conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of locating flow-through mixed flow engine nacelles in several aft underwing positions on the longitudinal aerodynamics of a high wing transport airplane. D-shaped inlet nacelles were used in the test. Some configurations with antishock bodies and with nacelle toe-in were also tested. Data were obtained for a free stream Mach number range of 0.70 to 0.85 and a model angle-of-attack range from -2.5 to 4.0 degrees.

Abeyounis, William K.↗

NASA NTRS1990

Wingtip vortex turbine investigation for vortex energy recovery

A flight test investigation has been conducted to determine the performance of wingtip vortex turbines and their effect on aircraft performance. The turbines were designed to recover part of the large energy loss (induced drag) caused by the wingtip vortex. The turbine, driven by the vortex flow, reduces the strength of the vortex, resulting in an associated induced drag reduction. A four-blade turbine was mounted on each wingtip of a single-engine, T-tail, general aviation airplane. Two sets of turbine blades were tested, one with a 15' twist (washin) and one with no twist. Th power recovered by the turbine and the installed drag increment were measured. A trade-off between turbine power and induced drag reduction was found to be a function of turbine blade incidence angle. This test has demonstrated that the wingtip vortex turbine is an attractive alternate, as well as an emergency, power source.

Abeyounis, William K.↗

NASA NTRS1990

Wingtip vortex turbine

A means for extracting rotational energy from the vortex created at aircraft wing tips which consists of a turbine with blades located in the crossflow of the vortex and attached downstream of the wingtip. The turbine has blades attached to a core. When the aircraft is in motion, rotation of a core transmits energy to a centrally attached shaft. The rotational energy thus generated may be put to use within the airfoil or aircraft fuselage.

Patterson, James C., Jr.↗

NASA NTRS1990

Preliminary flight test investigation of an airborne wake vortex detection concept

NASA and the FAA have conducted a brief flight-test investigation to furnish preliminary data on the feasibility of transport aircraft wake-vortices' detection, with a view to improving airport capacity by reducing the longitudinal in-trail spacing between aircraft on landing runs. Attention was given to the possibility that the detection of strong vortices at a sufficiently early stage might furnish reasonable warning of impending aerodynamic effects. Preliminary results indicate that while maximum detection distances obtainable with wingtip-mounted flow-angularity vanes are slightly lower than had been predicted, improved detector algorithms may render them more sensitive.

Verstynen, Harry A.↗

NASA NTRS1989

Compression Pylon

A compression pylon for an aircraft with a wing-mounted engine, that does not cause supersonic airflow to occur within the fuselage-wing-pylon-nacelle channel is presented. The chord length of the pylon is greater than the local chord length of the wing to which it is attached. The maximum thickness of the pylon occurs at a point corresponding to the local trailing edge of the wing. As a result, the airflow through the channel never reaches supersonic velocities.

Patterson, James C., Jr.↗

NASA NTRS1989

Compression Pylon Reduces Interference Drag

New design reduces total drag by 4 percent. Pylon reduces fuselage/wing/pylon/nacelle-channel compressibility losses without creating additional drag associated with other areas of pylon. Minimum cross-sectional area of channel occurs at trailing edge of wing. Velocity of flow in channel always nearly subsonic, reducing compressibility losses associated with supersonic flow. Flow goes past trailing edge before returning to ambient conditions, resulting in no additional drag to aircraft. Designed to compress flow beneath wing by reducing velocity in this channel, thereby reducing shockwave losses and providing increase in wing lift.

Patterson, James C., Jr.↗

NASA NTRS1987

Evaluation of installed performance of a wing-tip-mounted pusher turboprop on a semispan wing

An exploratory investigation has been conducted at the Langley Research Center to determine the effect of a wing-tip-mounted pusher turboprop on the aerodynamic characteristics of a semispan wing. Tests were conducted on a semispan model with an upswept, untapered wing and an airdriven motor that powered an SR-2 high-speed propeller located on the tip of the wing as a pusher propeller. All tests were conducted at a Mach number of 0.70 over an angle-of-attack range from approximately -2 to 4 deg at a Reynolds number of 3.82 x 10 to the 6th based on the wing reference chord of 13 in. The data indicate that, as a result of locating the propeller behind the wing trailing edge at the wing tip in the crossflow of the wing-tip vortex, it is possible to improve propeller performance and simultaneously reduce the lift-induced drag.

Patterson, James C., Jr.↗

NASA NTRS1986

Natural laminar flow nacelle for transport aircraft

The potential of laminar flow nacelles for reducing installed engine/nacelle drag was studied. The purpose was twofold: to experimentally verify a method for designing laminar flow nacelles and to determine the effect of installation on the extent of laminar flow on the nacelle and on the nacelle pressure distributions. The results of the isolated nacelle tests illustrated that laminar flow could be maintained over the desired length. Installing the nacelles on wing/pylon did not alter the extent of laminar flow occurring on the nacelles. The results illustrated that a significant drag reduction was achieved with this laminar flow design. Further drag reduction could be obtained with proper nacelle location and pylon contouring.

Lamb, Milton↗

NASA NTRS1961

An Investigation of the Influence of Body Size and Indentation Asymmetry of the Effectiveness of Body Indentation in Combination with a Cambered Wing

An investigation has been made of a 450 sweptback cambered wing in combination with an unindented body and a body symmetrically indented with respect to its axes designed for a Mach number of 1.2. The ratio of body frontal area to wing planform area was 0.08 for these wing-body combinations. In order to determine the influence of body size on the effectiveness of indentation, the test data have been compared with previously obtained data for similar configurations having a ratio of body frontal area to wing planform area of 0.04. Also, in order to investigate the relative effectiveness of indentation asymmetry, a specially indented body designed to account for the wing camber and also designed for a Mach number of 1.2 has been included in these tests. The investigation was conducted in the Langley 8-Foot Tunnels Branch at Mach numbers from 0.80 to 1.43 and a Reynolds number of approximately 1.85 x 10(exp 6), based on a mean aerodynamic chord length of 5.955 inches. The data indicate that the configurations with larger ratio of body frontal area to wing planform area had smaller reductions in zero-lift wave drag associated with body indentation than the configurations with smaller ratio of body frontal area to wing planform area. The 0.08-area-ratio configurations also had correspondingly smaller increases in the values of maximum lift-drag ratio than the 0.04-area-ratio configurations. The consideration of wing camber in the body indentation design resulted in a 35.5-percent reduction in zero-lift wave drag, compared with a 21.5-percent reduction associated with the symmetrical indentation, but had a negligible effect on the values of maximum lift-drag ratio.

Patterson, James C., Jr.↗