Search NASA⌕ Search

Engineering topics

Paul M Stremel

Publications and source records attributed to Paul M Stremel.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Comparison of OVERFLOW Computational and Experimental Results of the CobraMRV Mars Entry Vehicle Concept during Supersonic Retropropulsion

The CFD solver OVERFLOW was used to simulate the CobraMRV undergoing supersonic retropropulsion (SRP) in the Langley Unitary Plan Wind Tunnel as part of a CFD and wind-tunnel integration effort. The aerodynamics of the CobraMRV are summarized and comparisons to experimental data at flight conditions of interest are presented. The sensitivity of vehicle loads and flow field unsteadiness to CFD parameters at a subset of operating conditions are investigated.

CFD↗
NASA NTRS2024

OVERFLOW Guidelines for Simulation of Supersonic Retropropulsion

General methods for obtaining satisfactory simulation accuracy across a range of supersonic retropropulsive flows are recommended using comparisons between OVERFLOW calculations and tests of two vehicles in the Langley Unitary Plan Wind Tunnel. Gridding and discretization, various measures of solution convergence, and turbulence modelling options are dicussed. While the presented guidelines were developed from OVERFLOW simulations in support of a particular test, the recommendations on numerical methods and gridding practices hold merit for simulations conducted CFD solvers in general.

CFD↗
NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper describes the Dynamic Mode Decomposition (DMD) of the pressures on the scale model of the Space Launch System (SLS) Block 1 cargo vehicle with the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected in the Ascent Transient Aerodynamics Tests with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD) of the data matrix. For the matrix of the uPSP measurements of the SLS ATAT, the number of rows is equal to the number of nodes in the grid of the scale model, and the number of columns is equal to the number of frames in the videos taken with 4 Phantom high-speed cameras. In this paper, it is verified that, for the time series with zero mean value, the DMD is equivalent to the decomposition with the Discrete Fourier Transform (DFT). Considering the uPSP is mainly used in the assessment of the unsteady, aerodynamic phenomena, the DMD of the uPSP measurements can be implemented in two steps: (1) subtract the mean value from the uPSP measurement on each of the grid nodes; (2) apply the Fast Fourier Transform (FFT) on the resulting zero-mean time series. The DMD of the uPSP measurements with FFT has two advantages: (1) the computational complexity of FFT is O(N*logN), where N is the length of the time series; (2) compared to the SVD-based DMD algorithm, the DMD with FFT can be easily implemented in parallel processing. A sample matrix of uPSP measurements, at the size of 341 grid nodes and 128 frames, is generated. Figures 1 and 2 show the eigenvalues and the ratios of the eigenvectors, respectively, of the sample matrix, without and with the mean value removed on each of the grid nodes, computed with the SVD-based DMD and the FFT. The figures demonstrate the equivalence of the SVD-based DMD and the decomposition with DFT/FFT for the time series with zero mean value. The results of DMD of the uPSP measurements of the SLS ATAT in September 2019 are presented in the paper. The DMD modes at different frequencies are shown, the aerodynamic phenomena (e.g. shockwave and vortex shedding) are demonstrated and the correlation of the DMD modes with the test configuration parameter (e.g., the Mach Number) is discussed. Figure 3 shows a software tool to visualize the DMD modes. The code to implement the algorithm described in this paper was written in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, and executed on the NASA Pleiades supercomputer. Funding for this research was provided by the NASA Aerosciences Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

OVERFLOW Analysis of Supersonic Retropropulsion Testing on a Blunt Mars Entry Vehicle Concept

Supersonic Retropropulsion (SRP) flow over a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) blunt-body vehicle was simulated using the OVERFLOW Computational Fluid Dynamics (CFD) solver. Two nozzle configurations were tested (1E and 1F) as a subset of the seven total configurations in the Descent Systems Study (DSS) testing campaign. A generalized, Adaptive Mesh Refinement (AMR) shock capturing and plume refinement technique was developed and calibrated for producing automatic and optimized grid systems unique to any given testing condition. Simulations were subjected to successive levels of grid refinement in order to determine solution independence from grid resolution. OVERFLOW Reynolds Averaged Navier-Stokes (RANS) solutions produced realistic SRP flow phenomena, including Mach disk normal shocks contained in high-thrust plumes and bow shock triple-points. Solutions for the 1E nozzle configuration were steady. Conversely, a subset of the 1F test conditions were unsteady and exhibited periodic, non-sinsoidal expansions and contractions of the streamwise-oriented plume, resulting in unsteady aerodynamic loads on the vehicle.

Supersonic Retropropulsion↗
NASA NTRSDate not supplied

Evaluation of CFD Predictions of CobraMRV Control Surface Effectiveness at the NASA Langley Unitary Plan Wind Tunnel

The ability of CFD simulations to serve as a surrogate for wind tunnel testing at high supersonic speeds has been evaluated for a sub-scale model of the Co-Optimization Blunt-body Re-entry Analysis-Mid-lift-to-drag Rigid Vehicle (CobraMRV) human Mars entry vehicle concept. The vehicle was tested at the Unitary Plan Wind Tunnel (UPWT) at the NASA Langley Research Center under flow conditions and surface control configurations relevant to the entry stage of a flight mission. The CFD simulations were performed prior to gaining access to test results in order to assess how blind predictions obtained using best practices compare to experiments. Solutions of empty tunnel simulations were used as inflow boundary condition for the CobraMRV simulations in a truncated portion of the test section. Different solvers and turbulence models were used by separate teams to assess sensitivity to numerical methods, physics, and users. After release of the test results, the pre-test computations were compared to the experimental results, and additional analyses have been conducted to explain observed discrepancies. The amount of time and resources dedicated to each phase of the computational work was logged for comparison to that required for wind tunnel tests, and to inform planning of future CFD data base development projects.

ARMD↗
NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle with the Unitary Plan Wind Tunnel (UPWT) 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD). For the data with zero mean, the DMD is equivalent to the Discrete Fourier Transform (DFT). Since the uPSP is mainly used to determine the unsteady property of the aerodynamic flow, the DMD of the uPSP measurements is implemented in two steps: (1) subtract the mean value from the uPSP measurement; (2) apply the Fast Fourier Transform (FFT) on the resulting data with zero mean. The DMD of the uPSP measurements with FFT has two advantages: (1) the FFT algorithm is well known for its computational efficiency, therefore, compared to the SVD-based DMD algorithm, the DMD with FFT reduces the computation time; (2) the DMD with FFT can be easily implemented in parallel processing. The DMD outputs were generated with the execution in parallel of a code in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, on the NASA Pleiades supercomputer. In this paper, the results of DMD of the uPSP measurements in the tests of Mach sweep runs of the SLS ATAT are presented, and the effectiveness of the DMD of the uPSP measurements in the diagnosis of the unsteady, aerodynamic phenomena is demonstrated. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding for this research was provided by the NASA Aeroscience Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

OVERFLOW Analysis of Supersonic Retropropulsion Testing on a Blunt Mars Entry Vehicle Concept

Supersonic retropropulsion (SRP) flow over a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) blunt-body vehicle was simulated using the Overflow Computational Fluid Dynamics (CFD) solver. Two nozzle configurations were tested (1E and 1F) as a subset of the seven total configurations in the Descent System Study (DSS) testing campaign. A generalized, Adaptive Mesh Refinement (AMR) shock capturing and plume refinement technique was developed and calibrated for producing automatic and unique grid systems optimized for any given testing condition. Solution independence from grid resolution was determined by successively increasing grid refinement until asymptotic convergence of the mean aerodynamic loads was observed. Overflow Reynolds-averaged Navier-Stokes (RANS) solutions produced realistic SRP flow phenomena, including Mach disk normal shocks contained in high-thrust plumes and bow shock triple-points. Solutions for the 1E nozzle configuration were steady. Conversely, a subset of the 1F test conditions were unsteady and exhibited periodic, non-sinusoidal expansions and contractions of the streamwise-oriented plume, resulting in unsteady aerodynamic loads on the vehicle. Initial investigations into the effect of turbulence modeling fidelity demonstrated significant differences between the aerodynamic loads simulated with RANS and Detached Eddy Simulation (DES). Multiple flow mechanisms were identified as root causes of these differences, including bow shock shape augmentation and reduced entrainment due to reduced turbulence in the DES simulations. Initial comparisons of pitching moment control authority and aerodynamic drag performance between the tested nozzle configurations demonstrated that the 1E configuration may be more advantageous for the Mars Entry, Descent, and Landing (EDL) task.

Supersonic Retropropulsion↗
NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Phase I Development Overview

Since 2019, a group out of NASA Ames Research Center(ARC)has been focused on implementing systematic updates to make unsteady pressure-sensitive paint (uPSP) a more viable capability for production wind tunnel testing. Focusing on the general categories of data acquisition, data transfer, data processing, and data visualization, the uPSP Development Team has made several improvements to increase data quality and innovate a more workable system that would provide valuable surface pressure data to customers. As a result of the COVID-19 pandemic and several initial demonstration tests prior to the formal start of the development effort, the decision was made to focus on launch vehicles as the test article. To-date this development has focused on implementation in the ARC Unitary Plan Wind Tunnel 11-by11-footTransonic Wind Tunnel due to the large optical access of the test section and that the NASA Advanced Supercomputer is located at ARC. This paper summarizes the project origins and the results of four years of development effort, which will all culminate in a final demonstration test in the first half of2024.

unsteady pressure-sensitive paint↗
NASA NTRSDate not supplied

Comparison of OVERFLOW Computational and Experimental Results of the CobraMRV Mars Entry Vehicle Concept during Supersonic Retropropulsion

The CFD solver Overflow was used to simulate the CobraMRV undergoing supersonic retropropulsion (SRP) in the Langley Unitary Plan Wind Tunnel as part of a CFD and wind tunnel integration effort. Selection of numerical methods and resulting comparisons to selected tunnel conditions of interest are detailed. Comparisons of mean pressures with static taps and pressure-sensitive paint are provided for multiple SST-based turbulence models. URANS predicitons of heat shield pressures at high thrust conditions are poor compared to TMRC and DES predictions. Comparisons to experimental measurements of pressure fluctuations indicate complex relationships between heat shield unsteadiness, flight Mach number, and engine thrust coefficient. Bow shock topology and shock cell structure between experimental and OVERFLOW data show good agreement in Schlieren imaging. Recommendations for future investigation into flow field unsteadiness and turbulence models are suggested.

CFD↗