Search NASA⌕ Search

Engineering topics

Paul, Brian

Publications and source records attributed to Paul, Brian.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Microchannel Heat Exchanger Produced From a Metal Matrix Composite by Hybrid Laser Powder Bed Fusion and Inkjet Printing

Abstract This paper explores the production of an oxide dispersion strengthened (ODS) 304L stainless steel microchannel heat exchanger (HX) using a hybrid additive manufacturing process of laser powder bed fusion and inkjet printing. The study investigates the capabilities and economics of the hybrid inkjet-laser powder bed fusion (LPBF) process and evaluates the dimensional accuracy, functionality, and mechanical properties of the resulting ODS alloy. The effectiveness and pressure drop of the ODS heat exchangers produced by the hybrid LPBF tool are also determined. Results show that the inkjet-doped samples have a lower mean channel height with higher standard deviation than samples produced by LPBF alone. This is attributed to greater absorption of laser energy for the powder coated with the oxide precursor. The economic analysis shows that the hybrid process has a potential for reducing the unit cost of the heat exchanger based on cost modeling assumptions.

Engineering↗
DOE OSTI2024

A FeCrAl-Al2O3 Composite Produced via Laser Powder Bed Fusion of a Mixed Powder for Porous Catalyst Scaffolds

This study proposes a novel approach for synthesizing and etching bicontinuous FeCrAl-Al2O3 composites as a means for replacing FeCrAl foams as catalyst scaffolds in bio-driven alcohol reactors for jet-fuel production. Conventional FeCrAl foams suffer from poor availability and consequent high costs. New additive manufacturing techniques provide an opportunity to produce tailored foams in reasonable times and at acceptable costs. This research aimed to generate a porous FeCrAl structure by etching a bicontinuous FeCrAl-Al2O3 composite produced by laser powder bed fusion of amalgamated FeCrAl and Al2O3 powders. The composite powder for laser powder bed fusion is created by ball-milling FeCrAl and Al2O3 powders. This research focuses on achieving a bi-continuous FeCrAl-Al2O3 structure, essential for the selective removal of the ceramic phase. The influence of laser processing parameters on the microstructure was examined across a range of laser powers (60-120 W) and scan speeds (100-400 mm/s), showing that higher powers and speeds produce finer metal struts. A bi-continuous microstructure was consistently obtained, marking a key achievement. The Al2O3 removal process involved a two-step etching method using hydrochloric and phosphoric acids, tested across various etching times. The alumina phase was reduced from 36 vol% to 17 vol% (corresponding to an increase in porosity from 24 vol% to 43 vol%), showing the potential for use as a porous catalyst scaffold. This research demonstrates the potential for using additive manufacturing to produce porous FeCrAl structures capable of replacing hard-to-source FeCrAl foams.

Son, Kwangtae↗
DOE OSTI2021

Design Considerations for the Field Use of International Nuclear Safeguards Technology

The process of developing and deploying safeguards technology should be carried out in such a way that it supports the International Atomic Energy Agency’s (IAEA’s) international safeguards verification mission, while also being efficient in terms of both cost and time. This process, however, may be hindered by a general lack of nuclear facility operating experience among the scientists or engineers designing safeguards technology, or the inability to interact with the IAEA inspector end user. As a result, equipment designers may have difficulty understanding inspector needs and the limitations of using safeguards technology in the field, often leading to inefficiencies (in the form of increased cost and time spent) in the safeguards technology design process. Here, to mitigate this knowledge gap, the Y-12 National Security Complex in Oak Ridge, Tennessee, has developed design considerations that should be incorporated into safeguards technologies, focusing on non-destructive assay equipment. Timelines for integration of these considerations into the design process are also discussed.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
NASA NTRS1992

Display of scientific data structures for algorithm visualization

We present a technique for defining graphical depictions for all the data types defined in an algorithm. The ability to display arbitrary combinations of an algorithm's data objects in a common frame of reference, coupled with interactive control of algorithm execution, provides a powerful way to understand algorithm behavior. Type definitions are constrained so that all primitive values occurring in data objects are assigned scalar types. A graphical display, including user interaction with the display, is modeled by a special data type. Mappings from the scalar types into the display model type provide a simple user interface for controlling how all data types are depicted, without the need for type-specific graphics logic.

Hibbard, William↗