DNA Damage Baseline Predicts Resilience to Space Radiation and Radiotherapy
Not Available
Pariset, Eloise↗
Engineering topics
Paulino Lima, Ivan G.
Publications and source records attributed to Paulino Lima, Ivan G..
Using DNA Damage to Investigate the Individual Variability of Human Sensitivity to Ionizing Radiation
High-LET ionizing radiation is a major occupational health hazard for astronauts, but risk assessment remains elusive due to limited epidemiological data. Identifying genetic factors modulating the individual radiation response may be the most effective strategy to provide individualized risk management for long-duration high-radiation missions. We have started tackling the challenge of predicting individual risks by identifying human genetic loci associated with various radiation sensitivity phenotypes in primary blood mononuclear cells from a relatively large healthy human cohort. To date, we have performed the isolation of PBMCs from 768 subjects of the same ethnicity, and irradiated PBMCs from 576 subjects with 1 and 3 particles/100µm2 of 600 MeV/n 56Fe, 350 MeV/n 40Ar and 350 MeV/n 28Si ions. The phenotypes of interest were: number of radiation-induced foci (or RIFs), CellROX oxidative stress responses and cell death, at 4h and 24h following irradiation. We have observed a significant inter-individual variability at 0 Gy between the 576 studied subjects, with a mean fold difference between the 10% lowest and highest responders of 5.6 of RIFs/cell, 7.9 in mean CellRox intensity, and 9.3 in percentage of dead cells. In order to better assess genetic factors influencing DNA repair, we used a metric previously introduced by our group to sort out radiation sensitivity phenotypes in mice: i.e. the ratio of the first to the second slope of RIFs/cell (between 0 and 1, and between 1 and 3 particle/100µm2). Preliminary data on 192 individuals showed a distribution of ?low-dose responders? (ratio > 1) to ?high-dose responders? (ratio < 1) at 4h of 12%, 55% and 52% respectively for Fe, Ar and Si. The average value for the first and the second slopes was very similar for the two lowest LET (0.10 [-0.26;0.58] and 0.09 [-0.45;0.41] for Ar, 0.07 [-0.27;0.38] and 0.08 [-0.19;0.42] for Si), indicating a linear dose response across both fluence. Fe showed clear saturation for the highest dose with a slope of -0.09 [-0.86;1.51] against 0.68 [-2.21;2.20] for the low dose range, which probably reflects that many PBMCs are beyond repair at the high dose. Note that other significances were found for additional factors ? such as BMI and age ? whereas none were found for sex. GWAS will be performed on all phenotypes upon completion of measurements.
Pariset, E.↗
Myco-Architecture off Planet: Growing Surface Structures at Destination
Our work focused on filling major select key technical knowledge gaps, and technical aspects to be addressed in a Phase II proposal were identified such as the secretion of glues or plastics by the fungi or bacteria to form biocomposites. Specifically, we raised the technical TRL by assessing the growth of in-house mycelial-producing strains on potential food substrates and analyzed the advantages and disadvantages to their use off planet. Growth of the mycelia on sawdust and powdered nutrients including dried, powdered algae, was used as a baseline. We measured growth as a function of temperature, tested the relevant material properties of the mycelia products produced, and measured the mass of input and output volume for production per volume of material. Mycotecture was produced in a bag simulating the proposed mission implementation. Post-production such as heat treatment (as is done with terrestrial mycotecture)was assessed.The material properties of the dried, frozen and baked mycelial outputs included density, strength,thermal insulation and flame retardation. Tensile/compression testing on biocomposite material specimens was performed to obtain three-dimensional elastic constants, as well as to examine deformation and fracture behavior. These mechanical tests were performed on both dormant and activated samples to understand the evolution of the structural material. In addition, experimental data obtained from the mechanical testing was used to build a failure prediction model that accounts for material anisotropy. This aided in future structural design through a quantitative understanding of the mechanical limits of the material. To examine the texture, defects, fracture surfaces of the material, high-resolution microstructural imaging was utilized before and after the mechanical tests. This microstructural analysis informed us about the macro-structural behavior and influenced structural design. Thermal decomposition analysis was also performed tounderstand the thermal limits.
Biocomposites↗