Engineering topics

Pearlstein, Arne J.

Publications and source records attributed to Pearlstein, Arne J..

6 records

NASA NTRS1994

Use of rotation to suppress thermosolutal convection in directionally solidified binary alloys

Effects of rotation on onset of convection during plane-front directional solidification of Pb-Sn and the pseudobinary system mercury cadmium telluride (Hg(1-x)Cd(x)Te), and on dendritic solidification of Pb-Sn have been studied by means of linear stability analysis. Incorporating Coriolis and centrifugal accelerations into the momentum equation of Coriell et al., we find that under realistic processing conditions, a large degree of stabilization can be achieved using modest rotation rates for both Pb-Sn and mercury cadmium telluride. At a growth velocity of 5 micron/sec and nominal liquid-side temperature gradient of 200 K/cm in Pb-Sn, rotation at 500 rpm results in a hundredfold increase in the critical Sn concentration. Large increases in the maximum allowable growth velocity at fixed melt composition are also attainable with modest rotation rates. The effect is amplified under conditions of reduced gravitational acceleration. For Hg(1-x)Cd(x)Te, we have also studied the nonrotating case. The key differences are due to the existence of a composition range for Hg(1-x)Cd(x)Te in which the melt density has a local maximum as a function of temperature. When the melt solidifies by cooling from below, the liquid density may initially increase with distance above the interface, before ultimately decreasing as the melt temperature increases above the value at which the local density maximum occurs. In contrast to the Pb-Sn case where density depends monotonically on temperature and composition, for Hg(1-x)Cd(x)Te there exists a critical value of the growth velocity above which plane-front solidification is unstable for all bulk CdTe mole fractions. Again, rotation leads to significant inhibition of onset. We identify the predicted stabilization with the Taylor-Proudman mechanism by which rotation inhibits thermal convection in a single-component fluid heated from below. In a binary liquid undergoing solidification, rotation inhibits the onset of buoyancy-driven convection, and has no effect on the short-wavelength morphological instability. At large growth velocities, the plane-front interface between liquid and solid becomes unstable with respect to a morphological instability and solidification occurs dendritically, with a mushy zone of dendrites and interdendritic fluid separating the solid from the melt. For the Pb-Sn system, rotation substantially suppresses the onset of convection in the mushy zone and in the overlying liquid, holding open the promise that rotation can suppress freckling and other macrosegregation defects.

Pearlstein, Arne J.↗

NASA NTRS1993

Development of the wake behind a circular cylinder impulsively started into rotatory and rectilinear motion

The temporal development of a 2D viscous incompressible flow generated by a circular cylinder started impulsively into steady rotatory and rectilinear motion is studied by integration of a velocity/vorticity formulation of the governing equations, using an explicit finite-difference/pseudo-spectral technique and an implementation of the Biot-Savart law. Results are presented for a Reynolds number of 200 (based on the cylinder diameter 2a and the magnitude U of the rectilinear velocity) for several values of the angular/rectilinear speed ratio alpha = omega(a)/U (where omega is the angular speed) up to 3.25. Several aspects of the kinematics and dynamics of the flow not considered earlier are discussed. For higher values of alpha, the results indicate that for Re = 200, vortex shedding does indeed occur for alpha = 3.25. However, consecutive vortices shed by the body can be shed from the same side and be of the same sense, in contrast to the nonrotating case, in which mirror-image vortices of opposite sense are shed alternately on opposite sides of the body. The implications of the results are discussed in relation to the possibility of suppressing vortex shedding by open or closed-loop control of the rotation rate.

Chen, Yen-Ming↗

NASA NTRS1991

Convective instability in superposed fluid and anisotropic porous layers

The onset of thermal convection due to heating from below in a system consisting of a fluid layer overlying a porous layer with anisotropic permeability and thermal diffusivity is studied. The linear perturbation equations are solved numerically. It is found that the effects of anisotropy on the onset of thermal convection are most profound for small values of the depth ratio xi (ratio of fluid layer thickness to porous layer thickness), since in that case, the onset of convection corresponds to significant motion in both layers. For fixed vlues of the vertical permeability in the porous medium, decreasing the value of zeta (ratio of horizontal to vertical permeability) leads to stabilization of the superposed layer configuration because of increased resistance to motion in the porous medium. For larger values of xi, the onset of motion is increasingly confined to the fluid layer, with the transport of heat through the porous layer occurring primarily by conduction. Accordingly, the influence of zeta on the stability characteristics for larger xi is less significant than the effects of an anisotropic thermal conductivity.

Chen, Falin↗

NASA NTRS1991

Development of the wake behind a circular cylinder impulsively started into rotatory and rectilinear motion: Intermediate rotation rates

The temporal development of two-dimensional viscous incompressible flow generated by a circular cylinder started impulsively into steady rotatory and rectilinear motion is studied by integration of a velocity/vorticity formulation of the governing equations, using an explicit finite-difference/pseudo-spectral technique and an implementation of the Biot-Savart law. Results are presented for a Reynolds number of 200 (based on the cylinder diameter 2a and the magnitude U of the rectilinear velocity) for several values of the angular/rectilinear speed ratio alpha = (omega x a)/U (where omega is the angular speed) up to 3.25. Several aspects of the kinematics and dynamics of the flow not considered earlier are discussed. For higher values of alpha, the results indicate that for Re = 200, vortex shedding does indeed occur for alpha = 3.25. The shedding process is; however, very different from that which gives rise to the usual Karman vortex street for alpha = 0. In particular, consecutive vortices shed by the body can be shed from the same side and be of the same sense, in contrast to the nonrotating case, in which mirror-image vortices of opposite sense are shed alternately on opposite sides of the body. The implications of the results are discussed in relation to the possibility of suppressing vortex shedding by open or closed-loop control of the rotation rate.

Chen, Yen-Ming↗

NASA NTRS1991

Sensing and actuation in a liquid propellant rocket engine

Equations describing the conservation of mass, momentum, and energy, and multicomponent transport and chemical reaction in a liquid propellant rocket (LPR) engine are given, along with appropriate boundary conditions. The formulation includes a detailed description of the two-phase (gas/liquid) flow in terms of a moving boundary problem, with droplets and vapor occupying time-dependent subdomains of the LPR chamber. Several sensor and actuator types are considered in detail, and their mathematical descriptions are incorporated into the differential equations and boundary conditions.

Bentsman, Joseph↗

NASA NTRS1990

Control-oriented modeling of combustion and flow processes in liquid propellant rocket engines

This paper presents a control-oriented model of the flow, reaction, and transport processes in liquid propellant rocket combustion chambers, based on the multicomponent conservation laws of gas dynamics. This model provides a framework for the inclusion of detailed chemical kinetic relations, viscous and other dissipative effects, a variety of actuators and sensors, as well as process and measurement disturbances. In addition to its potential usefulness to the designer in understanding the dynamical complexity of the system and the sources of model uncertainty, the model provides a rigorous basis for control system design. An appraisal of current and feasible actuators and sensors, and their mathematical representation are included.

Bentsman, Joseph↗