Search NASA⌕ Search

Engineering topics

Pecharsky, Vitalij

Publications and source records attributed to Pecharsky, Vitalij.

At least 19 records

Scalable and compact magnetocaloric heat pump technology

Magnetocaloric heat pumping (MCHP) promises to be more efficient than traditional vapor compression while also eliminating the deleterious effects of gaseous refrigerants. While MCHP devices have shown the temperature spans and efficiencies needed for different heating and cooling applications, they struggle to become commercially viable due to their large size and mass, and resultant high cost. This paper evaluates a baseline MCHP device and explores methods to boost its system power density (SPD). The key components of the baseline system are the gadolinium packed-particle bed active magnetic regenerator (AMR) and a magnetic source composed of permanent magnets and high permeability magnetic steel. To enhance the SPD, the paper evaluates maximizing the AMR volume, opting for first-order magnetocaloric materials, optimizing the magnet and AMR geometry, and reducing the size of magnets and magnetic steel parts. At larger thermal powers, increasing the AMR diameter and the number of magnetic poles were evaluated. Using finite element models, solid models, and estimates of magnetocaloric material performance, thermal powers ranging from 37 W to 44 kW at a nominal 10 K temperature span were projected, and SPD was estimated to improve from 6 W/kg to 81 W/kg. Neglecting end effects, an upper limit of 114 W/g is estimated. Compared to SPD of off-the-shelf compressors with similar environment temperatures, MCHP power density using gadolinium is competitive up to roughly 200 W of cooling power. This is extended to 1 kW when using LaFeSi alloys and up to 3 kW in the limiting case. In conclusion, these results indicate that the performance and mass of MCHP can match that of compressors, which is a critical step toward cost-competitive magnetocaloric technology.

42 ENGINEERING↗

Unlocking large compressive strains in thin active elastocaloric layers

Elastocaloric cooling attracts broad interest and rapidly growing attention due to its potential for high efficiency and low environmental impact. While it is common knowledge that triggering reversible entropy and temperature changes with stress applied in compression prevents rapid failures of materials, realizing this regime in elastocaloric systems is highly challenging because nearly all geometries suited for efficient heat transfer are prone to buckling even under modest loads. This work describes a concept of a novel composite, where an active NiTi layer is embedded into a polymer support structure such that the elastocaloric material is entirely in compression when the assembly is subjected to bending. The active layer achieves 8.1 K temperature change at 2.5% compressive strain without buckling. After 10,000 cycles at 2% compressive strain, the composite maintains mechanical integrity without degradation of the elastocaloric effect. The results demonstrate that NiTi and, potentially, other elastocalorically active materials in geometries previously thought impossible can be successfully implemented in regenerative cooling systems operating in compression.

42 ENGINEERING↗

Active magnetic regenerative cooling with smaller magnets

Magnetocaloric heat pumping near room temperature, a.k.a. magnetic cooling, relies on the active regenerator cycle to achieve functional temperature spans and realize economic and societal benefits promised by this emerging solid-state cooling technology. The cycle itself depends upon synchronizing oscillating flow of a heat transfer fluid through a solid porous active material matrix, or the refrigerant, with periods when the refrigerant is in the highest available (field-on) and in nearly zero (field-off) magnetic fields to accomplish heat transfer. With this in mind, in this work we analyze varying flow and magnetic field wave forms and the timing between when the fluid is pumped and when the magnetic field is turned on and off. We demonstrate that the volume and the cost of permanent magnet generating the field changes can be cut nearly in half with little to no effect on the device temperature span and cooling power normalized by the refrigerant mass.

36 MATERIALS SCIENCE↗

Compact and efficient elastocaloric heat pumps—Is there a path forward?

Elastocaloric cooling holds promise for energy-efficient heat pumping near room temperature with low environmental impact. Its adoption is, however, impeded by disproportionally large sizes of actuators compared with the active material volume. Taking magnetocaloric cooling as the baseline, the value of no more than 10:1 actuator volume to active material volume should lead to both size- and cost-effective solutions that may potentially be competitive with vapor-compression devices. With the goal to establish performance metrics that can lead to informed actuator selection for specific regenerator requirements, we analyze a wide range of elastocaloric materials and actuator technologies to find the best matches. We find that actuation with magnetic shape memory alloys meets all requirements; however, this technology is currently in early developmental stages and such actuators are not widely commercially available. Another promising and easily accessible option is standard rotary electric motors in combination with rotary-to-linear transduction mechanisms. A theoretical analysis of two case studies of elastocaloric systems using rotary electric motors with a Scotch yoke mechanism demonstrates the usefulness of our approach. Actuator requirements are based on two different regenerator configurations: one starting from zero strain without any mechanical energy recovery and another with 2% pre-strain and mechanical energy recovery to reduce the power and torque required from the motor. Our results indicate that the 10:1 target actuator to active material volume ratio can be met and feasibly lowered further, demonstrating that the proposed method for selecting actuators makes compact and efficient elastocaloric systems possible.

42 ENGINEERING↗

From a conventional ferromagnetism to a frustrated magnetism: An unexpected role of Fe in Nd(Al 1-x Fe x ) 2 (x ≤ 0.2)

The structure and magnetic properties of Nd(Al 1-x Fe x ) 2 alloys with x = 0, 0.05, 0.1 and 0.2, which adopt cubic MgCu 2 -type structure with space group Fd3¯m, are studied using x-ray powder diffraction, static and dynamic magnetization, and calorimetric measurements. The lattice constant decreases linearly with increasing Fe content from 8.0106(4) Å to 7.9044(4) Å. Large thermal irreversibilities between zero-field-cooled and field-cooled conditions are observed for all substituted samples. Here, the magnetic transition temperatures exhibit a minimum for x = 0.1, and coercive fields at 2 K increase from 70 Oe for x = 0 to 6.3 kOe for x = 0.2. The absence of λ-type peak in the heat capacity data, frequency dependence of ac magnetic susceptibility, and memory effects indicate formation of a cluster-glass magnetic state when x ≥ 0.1.

36 MATERIALS SCIENCE↗

CaloriSMART: Small-scale test-stand for rapid evaluation of active magnetic regenerator performance

We report operation of a device designed specifically for rapid experimental evaluation of performance of magnetocaloric materials in different magnetic fields using a compact active magnetic regenerator bed with a total volume of approximately 5 mL. Other features of the system include digital control of the rotating-permanent-magnet field source and custom dual-opposed syringe pump that enable precise tuning and coupling of the flow profile and the magnetic field profile. Performance of the device is demonstrated for flow volumes between 1 and 4 mL (utilization from 0.48 to 1.9), maximum magnetic fields of 1.13 and 1.45 T, and applied cooling powers from 0 to 20 W at frequencies from 0.5 to 4 Hz. A regenerator comprised of 25 g of 200 µm spherical Gd powder reached temperature spans of 19.3 K under no applied cooling load and 2.6 K under the maximum applied cooling load of 20 W. The device also achieves a very high specific exergetic cooling power of 73 W L -1 T -1 . Results obtained at two different maximum magnetic fields in the same device suggest a powerful new scaling for regenerator performance: the exergetic power quotient. The exergetic power quotient shows a simple scaling of device cooling performance with the amount of active material and the magnetic field strength. This suggests results from a small device correlate to expected performance of a larger regenerator, making the exergetic power quotient a well-suited parameter for evaluating functionality of active magnetic regenerators employing new magnetocaloric materials.

47 OTHER INSTRUMENTATION↗

Antiferromagnetism of β-Ce under hydrostatic pressure

Here the magnetic properties of β-Ce at low temperature have been studied through ac susceptibility measurements under hydrostatic He-gas pressure up to 4.5 kbar. The Néel temperature, T N = 12.7 K at 58 bar, initially increases with pressure at the rate d T N / dP = +0.32 ± 0.05 K/kbar. After releasing pressure from 4.5 to 0.06 kbar at 40 K, the magnetic susceptibility anomaly associated with the antiferromagnetic transition is markedly reduced. Surprisingly, T N also shifts from 12.7 to 14 K. Both effects likely arise from an irreversible β → α transition under pressure.

36 MATERIALS SCIENCE↗

Room temperature ferromagnetic gadolinium silicide nanoparticles

A particle usable as T 1 and T 2 contrast agents is provided. The particle is a gadolinium silicide (Gd 5 Si 4 ) particle that is ferromagnetic at temperatures up to 290 K and is less than 2 .mu.m in diameter. An MRI contrast agent that includes a plurality of gadolinium silicide (Gd.sub.5Si.sub.4) particles that are less than 1 .mu.m in diameter is also provided. A method for creating gadolinium silicide (Gd 5 Si 4 ) particles is also provided. The method includes the steps of providing a Gd 5 Si 4 bulk alloy; grinding the Gd 5 Si 4 bulk alloy into a powder; and milling the Gd 5 Si 4 bulk alloy powder for a time of approximately 20 minutes or less.

36 MATERIALS SCIENCE↗

Magnetocaloric behavior in ternary europium indides EuT 5 In: Probing the design capability of first-principles-based methods on the multifaceted magnetic materials

The most favorable structures and the types of magnetic ordering predicted from first-principles-based methods in a family of closely related transition-metal-rich indides EuT 5 In (T = Cu, Ag, Au) are gauged against relevant experiments. The EuT5In compounds adopt a different structure for each different coinage metal—EuCu 5 In ( hR 42; R $\overline{3}$m, a = 5.0933(7), c = 30.557(6) Å), EuAg 5 In ( oP 28; Pnma , a = 9.121(2), b = 5.645(1), c = 11.437(3) Å), and EuAu 5 In ( tI 14; I 4/ mmm , a = 7.1740(3), c = 5.4425(3) Å)—and crystallize with the Sr 5 Al 9 , CeCu 6 , and YbMo 2 Al 4 structure types, respectively. EuCu 5 In and EuAg 5 In order antiferromagnetically at T N = 12 and 6 K, respectively, whereas EuAu 5 In is ferromagnetic below T C = 13 K. EuCu 5 In exhibits complex magnetism: after the initial drop at T N , the magnetization rises again below 8 K, and a weak metamagnetic-like transition occurs at 2 K in μ 0 H = 1.8 T. The electronic heat capacity of EuCu 5 In, γ = ~400 mJ/(mol K 2 ), points to strong electronic correlations. Spin-polarized densities of states suggest that the magnetic interactions in the three materials studied are supported via mixing 4 f and 5 d states of Eu. As a result, a chemical bonding analysis based on the Crystal Orbital Hamilton populations reveals the tendency to maximize overall bonding as a driving force to adopt a particular type of crystal structure.

36 MATERIALS SCIENCE↗

EuNi 5 InH 1.5-x (x = 0–1.5): hydrogen induced structural and magnetic transitions

The new quaternary hydride EuNi 5 InH 1.5 has been obtained by hydrogenation of the intermetallic parent EuNi5In under extremely mild conditions, hence, at room temperature and low hydrogen pressure. Hydrogenation at slightly elevated temperatures and pressures allows for the growth of large crystals, which is a rare observation for intermetallic hydrides. EuNi 5 InH 1.5 crystallizes in its own structure type ( hP 17, P6¯m2 , a = 4.9437(6), c = 10.643(1) Å) with a unique arrangement of the intermetallic host. The hydrogen atoms prefer Ni-surrounded positions, occupying {EuNi 3 } and {Eu 2 Ni 2 } tetrahedral voids in the structure. Upon hydrogenation of EuNi 5 In an anisotropic volume expansion accompanied with a decrease of symmetry is observed. Magnetic measurements reveal antiferromagnetic ordering in the hydride below 4 K and indicate an intermediate +II/+III oxidation state for Eu both in the intermetallic phase and the hydride. X-ray photoemission spectroscopy confirms the existence of the two different oxidation states of Eu. The hydrogenation does not affect the oxidation state of Eu and the type of magnetic ordering, but exerts a strong influence on the transition temperature, crystal structure, mechanical and electrical properties. Crystallographic analysis suggests that Eu(II) and Eu(III) do not order but rather mix homogeneously on crystallographic sites. Electronic structure calculations reveal the metallic character of the hydride with several different types of chemical bonding interactions being present in the compound ranging from the formally ionic Eu–H to covalent Ni–H and delocalized metal–metal. As a result, geometry optimization confirm the thermodynamic instability of the intermetallic host lattice for the hydride and supports a transformation into the parental structure as observed experimentally.

36 MATERIALS SCIENCE↗

Cation-poor complex metallic alloys in Ba(Eu)–Au–Al(Ga) systems: Identifying the keys that control structural arrangements and atom distributions at the atomic level

Four complex intermetallic compounds BaAu 6±x Ga 6±y (x = 1, y = 0.9) (I), BaAu 6±x Al 6±y (x = 0.9, y = 0.6) (II), EuAu 6.2 Ga 5.8 (III), and EuAu 6.1 Al 5.9 (IV) have been synthesized, and their structures and homogeneity ranges have been determined by single crystal and powder X-ray diffraction. Whereas I and II originate from the NaZn 13 -type structure (cF104–112, Fm3C), III (tP52, P4/nbm) is derived from the tetragonal Ce 2 Ni 17 Si 9 -type, and IV (oP104, Pbcm) crystallizes in a new orthorhombic structure type. Both I and II feature formally anionic networks with completely mixed site occupation by Au and triel (Tr = Al, Ga) atoms, while a successive decrease of local symmetry from the parental structures of I and II to III and, ultimately, to IV correlates with increasing separation of Au and Tr on individual crystallographic sites. Density functional theory-based calculations were employed to determine the crystallographic site preferences of Au and the respective triel element to elucidate reasons for the atom distribution (“coloring scheme”). Chemical bonding analyses for two different “EuAu 6 Tr 6 ” models reveal maximization of the number of heteroatomic Au–Tr bonds as the driving force for atom organization. The Fermi levels fall in broad pseudogaps for both models allowing some electronic flexibility. Spin-polarized band structure calculations on the “EuAu 6 Tr 6 ” models hint to singlet ground states for europium and long-range magnetic coupling for both EuAu 6.2 Ga 5.8 (III) and EuAu 6.1 Al 5.9 (IV). This is substantiated by experimental evidence because both compounds show nearly identical magnetic behavior with ferromagnetic transitions at T C = 6 K and net magnetic moments of 7.35 μB/f.u. at 2 K. As a result, the effective moments of 8.3 μB/f.u., determined from Curie–Weiss fits, point to divalent oxidation states for europium in both III and IV.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Short-Range Magnetic Correlations and Parimagnetism in RCo 2

X-ray circular magnetic dichroism, polarized neutron diffraction, ac susceptibility, and Seebeck effect have been measured for several members of the RCo 2 series (R=Ho, Tm, Er) as a function of temperature and applied magnetic field. The experimental results show robust parimagnetism (a general behaviour along the RCo 2 series with R being a heavy rare earth ion) and two reversal temperatures in some systems, which is an unexpected result. Polarised neutron diffraction show differences between results obtained on single crystals or polycrystalline ingots. We propose an interpretation of parimagnetic RCo 2 as a Griffiths phase of the high temperature, magnetically ordered, amorphous RCo 2 phase. Copyright EDP Sciences, SIF, Springer-Verlag Berlin Heidelberg 2013

36 MATERIALS SCIENCE↗

Solid-State NMR Study of Li-Assisted Dehydrogenation of Ammonia Borane

The mechanism of thermochemical dehydrogenation of the 1:3 mixture of Li3AlH6 and NH3BH3 (AB) has been studied by the extensive use of solid-state NMR spectroscopy and theoretical calculations. The activation energy for the dehydrogenation is estimated to be 110 kJ mol–1, which is lower than for pristine AB (184 kJ mol–1). The major hydrogen release from the mixture occurs at 60 and 72 °C, which compares favorably with pristine AB and related hydrogen storage materials, such as lithium amidoborane (LiNH2BH3, LiAB). The NMR studies suggest that Li3AlH6 improves the dehydrogenation kinetics of AB by forming an intermediate compound (LiAB)x(AB)1–x. A part of AB in the mixture transforms into LiAB to form this intermediate, which accelerates the subsequent formation of branched polyaminoborane species and further release of hydrogen. The detailed reaction mechanism, in particular the role of lithium, revealed in the present study highlights new opportunities for using ammonia borane and its derivatives as hydrogen storage materials.

36 MATERIALS SCIENCE↗