High-Resolution Secondary Ion Mass Spectrometry Depth Profiling of Nanolayers
Abstract not provided
Engineering topics
Publications and source records attributed to Pellin, M J.
Abstract not provided
Abstract not provided
Explore the source record for details and available documents.
The use of broad bandwidth lasers with automated feedback control of wavelength was applied to the measurement of {sup 235}U/{sup 238}U ratios by resonance ionization mass spectrometry (RIMS) to decrease laser-induced isotopic fractionation. By broadening the bandwidth of the first laser in a three-color, three-photon ionization process from a bandwidth of 1.8 GHz to about 10 GHz, the variation in sequential relative isotope abundance measurements decreased from 10% to less than 0.5%. This procedure was demonstrated for the direct interrogation of uranium oxide targets with essentially no sample preparation.
Model silver nanocatalysts between 9 and 23 nm in size were prepared by size-selected cluster deposition from a free cluster beam on amorphous alumina films and their size-dependent catalytic performance studied in the partial oxidation of propylene under realistic reaction conditions. Smaller clusters preferentially produced acrolein, while the 23 nm particles were considerably more selective towards the formation of propylene oxide, at reaction rates far exceeding those previously reported for larger silver particles. The activity of clusters dropped significantly with increasing particle size. First-principle calculations, of the activation energies for oxygen adsorption and its dissociation, at variable surface coverage yielded surface energies which resulted in particle shapes resembling the experimentally observed shapes of partially oxidized silver clusters. The calculated activation barriers for propylene oxide and acrolein formation on various facets and on the edges of the nanoparticles provided detailed information about the energetics of the competing reaction pathways. The size- and corresponding morphology dependent theoretical activity and selectivity are in good accord with experimental observations.
RIMS depth profiles have been measured for Cr and Ca in Genesis solar wind collector made from Si and compared to such measurements for ion-implanted Si reference material. The presence of surface contamination has been shown to be a significant factor influencing the total Ca and Cr fluence measured in the Genesis collectors. A procedure to remove the contaminant signal from these depth profiles using the reference material implanted with a minor isotope demonstrated that 36% of the measured Ca fluence in our Genesis sample comes from terrestrial contamination.
The reliability and performance of silicon carbide (SiC) shaft seals on multipurpose mechanical pumps are improved by applying a protective coating of ultrananocrystalline diamond (UNCD). UNCD exhibits extreme hardness (97 GPa), low friction (0.1 in air) and outstanding chemical resistance. Consequently, the application of UNCD coatings to multipurpose mechanical pump seals can reduce frictional energy losses and eliminate the downtime and hazardous emissions from seal failure and leakage. In this study, UNCD films were prepared by microwave plasma chemical vapor deposition utilizing an argon/methane gas mixture. Prior to coating, the SiC seals were subjected to mechanical polishing using different grades of micron-sized diamond powder to produce different starting surfaces with well-controlled surface roughnesses. Following this roughening process, the seals were seeded by mechanical abrasion with diamond nanopowder, and subsequently coated with UNCD. The coated seals were subjected to dynamic wear testing performed at 3600 RPM and 100 psi for up to 10 days during which the seals were periodically removed and inspected. The UNCD-coated seals were examined using Raman microanalysis, scanning electron microscopy, optical profilometry, and adhesion testing before and after the wear testing. These analyses revealed that delamination of the UNCD films was prevented when the initial SiC seal surface had an initial roughness >0.1 {micro}m. In addition, the UNCD surfaces showed no measurable wear as compared to approximately 0.2 {micro}m of wear for the untreated SiC surfaces.
No abstract prepared.
Niobium carbide thin films were synthesized by atomic layer deposition (ALD) using trimethylaluminum (TMA), NbF{sub 5}, and NbCl{sub 5} precursors. In situ quartz crystal microbalance (QCM) measurements performed at 200 and 290 C revealed controlled, linear deposition with a high growth rate of 5.7 and 4.5 {angstrom}/cycle, respectively. The chemical composition, growth rate, structure, and electronic properties of the films were studied over the deposition temperature range 125-350 C. Varying amounts of impurities, including amorphous carbon (a-C), AlF{sub 3}, NbF{sub x}, and NbCl{sub x}, were found in all samples. A strong growth temperature dependence of film composition, growth rate, and room temperature DC resistivity was observed. Increasing film density, decreasing total impurity concentration, and decreasing resistivity were observed as a function of increasing deposition temperature for films grown with either NbF{sub 5} or NbCl{sub 5}. Superconducting quantum interference device (SQUID) magnetometry measurements down to 1.2 K revealed a superconducting transition at T{sub c} = 1.8 K in a 75 nm thick film grown at 350 C with TMA and NbF{sub 5}. The superconducting critical temperature could be increased up to 3.8 K with additional use of NH{sub 3} during ALD film growth.
Nanostructured metal films have been widely studied for their roles in sensing, catalysis, and energy storage. In this work, the synthesis of compositionally controlled and nanostructured Pt/Ir films by atomic layer deposition (ALD) into porous anodized aluminum oxide templates is demonstrated. Templated ALD provides advantages over alternative synthesis techniques, including improved film uniformity and conformality as well as atomic-scale control over morphology and composition. Nanostructured Pt ALD films are demonstrated with morphological control provided by the Pt precursor exposure time and the number of ALD cycles. With these approaches, Pt films with enhanced surface areas, as characterized by roughness factors as large as 310, are reproducibly synthesized. Additionally, nanostructured Ptlr alloy films of controlled composition and morphology are demonstrated by templated ALD, with compositions varying systematically from pure Pt to pure Ir. Lastly, the application of nanostructured Pt films to electrochemical sensing applications is demonstrated by the non-enzymatic sensing of glucose.
Iridium oxide (IrOx) has been widely studied due to its applications in electrochromic devices, pH sensing, and neural stimulation. Previous work has demonstrated that both Ir and IrOx films with porous morphologies prepared by sputtering exhibit significantly enhanced charge storage capacities. However, sputtering provides only limited control over film porosity. In this work, we demonstrate an alternative scheme for synthesizing nanoporous Ir and activated IrOx films (AIROFs). This scheme utilizes atomic layer deposition to deposit a thin conformal Ir film within a nanoporous anodized aluminum oxide template. The Ir film is then activated by potential cycling in 0.1 M H{sub 2}SO{sub 4} to form a nanoporous AIROF. The morphologies and electrochemical properties of the films are characterized by scanning electron microscopy and cyclic voltammetry, respectively. The resulting nanoporous AIROFs exhibit a nanoporous morphology and enhanced cathodal charge storage capacities as large as 311 mC/cm{sup 2}.
Size and support effects in the oxidative decomposition of methanol on amorphous alumina supported subnanometer palladium clusters were studied under realistic reaction conditions of pressure and temperature. The smaller Pd{sub 8-12} clusters were found to promote the decomposition channel to CO and hydrogen, however with mediocre activity due to poisoning. The larger Pd{sub 15-18} clusters preferentially produce dimethyl ether and formaldehyde, without signs of posioning. A thin titania overcoat applied on the Pd{sub 15-18} improves the sintering-resistance of the catalyst. Accompanying density functional calculations confirm the posioning of small Pd clusters by CO.
Production of the industrial chemical propylene oxide is energy-intensive and environmentally unfriendly. Catalysts based on bulk silver surfaces with direct propylene epoxidation by molecular oxygen have not resolved these problems because of substantial formation of carbon dioxide. We found that unpromoted, size-selected Ag{sub 3} clusters and {approx}3.5-nanometer Ag nanoparticles on alumina supports can catalyze this reaction with only a negligible amount of carbon dioxide formation and with high activity at low temperatures. Density functional calculations show that, relative to extended silver surfaces, oxidized silver trimers are more active and selective for epoxidation because of the open-shell nature of their electronic structure. The results suggest that new architectures based on ultrasmall silver particles may provide highly efficient catalysts for propylene epoxidation.
Due to its chemical stability, uniform pore size, and high pore density, nanoporous alumina is being investigated for use in biosensing, drug delivery, hemodialysis, and other medical applications. In recent work, we have examined the use of atomic layer deposition for coating the surfaces of nanoporous alumina membranes. Zinc oxide coatings were deposited on nanoporous alumina membranes using atomic layer deposition. The zinc oxide-coated nanoporous alumina membranes demonstrated antimicrobial activity against Escherichia coli and Staphylococcus aureus bacteria. These results suggest that atomic layer deposition is an attractive technique for modifying the surfaces of nanoporous alumina membranes and other nanostructured biomaterials. Nanoporous alumina, also known as anodic aluminum oxide (AAO), is a nanomaterial that exhibits several unusual properties, including high pore densities, straight pores, small pore sizes, and uniform pore sizes. In 1953, Keller et al. showed that anodizing aluminum in acid electrolytes results in a thick layer of nearly cylindrical pores, which are arranged in a close-packed hexagonal cell structure. More recently, Matsuda & Fukuda demonstrated preparation of highly ordered platinum and gold nanohole arrays using a replication process. In this study, a negative structure of nanoporous alumina was initially fabricated and a positive structure of a nanoporous metal was subsequently fabricated. Over the past fifteen years, nanoporous alumina membranes have been used as templates for growth of a variety of nanostructured materials, including nanotubes, nanowires, nanorods, and nanoporous membranes.
A series of cobalt-containing redox couples, based on [Co(1,10-phenanthroline){sub 3}](ClO{sub 4}){sub 2} and its derivatives, were prepared for use as regenerators/shuttles in dye-sensitized solar cells featuring modified TiO{sub 2} photoelectrodes. Surface modification and trap-state passivation of the TiO{sub 2} nanoparticle film electrodes were accomplished via atomic layer deposition of an ultrathin alumina coating. Electron lifetimes were then extracted from open-circuit voltage decay measurements. Cells employing alumina barrier/passivation layers exhibited higher open-circuit voltages as shuttles with more positive redox potentials were used, with the Co(5-nitro-phen){sub 3}{sup 3+/2+} couple exhibiting the highest V{sub oc} (0.844 V). Analysis of the open-circuit voltages and electron lifetimes indicate Marcus normal-region behavior for back electron transfer from the TiO{sub 2} photoanode to these compounds.
Abstract not provided
Abstract not provided