Engineering topics
Publications and source records attributed to Pelouch, J. J., Jr..
The workings of systems integration, its accomplishments, the influences of its character changes on the STS, propulsion out of the orbiter and LSS, and technological demands are discussed. The task of systems integration is to define, understand, and account for interactions between the major systems on a space mission. The safety and propulsion systems and their reliability are outlined.
The need for large structures in high orbit is discussed in terms of the many mission opportunities which require such structures. Mission and transportation options for large structures are presented, and it is shown that low-thrust propulsion is an enabling requirement for some missions and greatly enhancing to many others. A general comparison of electric and low-thrust chemical propulsion is made and the need for and requirements of low-thrust chemical propulsion are discussed in terms of the interactions that are perceived to exist between the propulsion system and the large structure.
Chemical and electric propulsion technologies for operations beyond the shuttle's orbit with focus on future mission needs and economic effectiveness is discussed. The adequacy of the existing propulsion state-of-the-art, barriers to its utilization, benefit of technology advances, and the prognosis for advancement are the themes of the discussion. Low-thrust propulsion for large space systems is cited as a new technology with particularly high benefit. It is concluded that the shuttle's presence for at least two decades is a legitimate basis for new propulsion technology, but that this technology must be predicted on an awareness of mission requirements, economic factors, influences of other technologies, and real constraints on its utilization.
The need for large structures in high orbit is reported in terms of the many mission opportunities which require such structures. Mission and transportation options for large structures are presented, and it is shown that low-thrust propulsion is an enabling requirement for some missions and greatly enhancing to many others. Electric and low-thrust chemical propulsion are compared, and the need for an requirements of low-thrust chemical propulsion are discussed in terms of the interactions that are perceived to exist between the propulsion system and the large structure.
This paper discusses Shuttle-era, chemical and electric propulsion technologies for operations beyond the Shuttle's orbit with focus on future mission needs and economic effectiveness. The adequacy of the existing propulsion state-of-the-art, barriers to its utilization, benefit of technology advances, and the prognosis for advancement are the themes of the discussion. Low-thrust propulsion for large space systems is cited as a new technology with particularly high benefit. It is concluded that the Shuttle's presence for at least two decades is a legitimate basis for new propulsion technology, but that this technology must be predicated on an awareness of mission requirements, economic factors, influences of other technologies, and real constraints on its utilization.
Combined ASRDI Data-Management and Analysis Technique (CADMAT) is system of computer programs and procedures that can be used to conduct data-management tasks. System was developed specifically for use by scientists and engineers who are confronted with management and analysis of large quantities of data organized into records of events and parametric fields. CADMAT is particularly useful when data are continually accumulated, such as when the need of retrieval and analysis is ongoing.
This vocabulary listing characterizes the contents of over 10,000 documents of the NASA Aerospace Safety Research and Data Institute's (ASRDI) safety engineering collection. The ASRDI collection is now one of the series accessible on the NASA RECON data base. There are approximately 6,300 postable terms that describe literature in the areas of cryogenic fluid safety, specifically hydrogen, oxygen, liquified natural gas; fire and explosion technology; and the mechanics of structural failure. To facilitate the proper selection of information nonpostable, related and array terms have been included in this listing.
Ignition temperatures of n-hexane, n-octane, n-decane, JP-6 jet fuel, and aircraft engine oil MIL-7-7808 (0-60-18) were determined in air using heated Pyrex cylinders and Nichrome wires, rods, or tubes. Ignition temperature varied little with fuel-air ratio, but increased as the size of the heat source was decreased. Expressions are given which define the variation of the hot surface ignition temperatures of these combustibles with the radius and the surface area of the heat source. The expressions are applicable to stagnant or low velocity flow conditions (less than 0.2 in./sec.). In addition, the hot gas ignition temperatures of the combustible vapor-air mixtures were determined with jets of hot air. These ignition temperatures also varied little with fuel-air ratio and increased as the diameter of the heat sources was decreased.
Bibliographic citations are presented to describe and define aircraft safety methods, equipment, and criteria. Some of the subjects discussed are: (1) fire and explosion suppression using whiffle balls, (2) ultraviolet flame detecting sensors, (3) evaluation of flame arrestor materials for aircraft fuel systems, (4) crash fire prevention system for supersonic commercial aircraft, and (5) fire suppression for aerospace vehicles.
A literature survey and analysis of the material and process factors affecting the safety of metals in oxygen systems is presented. In addition, the practices of those who specify, build, or use oxygen systems relative to the previous is summarized. Alloys based on iron, copper, nickel, and aluminum were investigated representing the bulk of metals found in oxygen systems. Safety-related characteristics of other miscellaneous metals are summarized. It was found that factors affecting the safety of metals in oxygen systems exit in all phases of the evolutionary process, from smelting and mill techniques through end-production fabrication. The safety of a given metal in an oxygen system was determined to be influenced by the particular service requirement. The metal characteristics should favorably influence fulfillment of these requirements. Thus, no singular metal or alloy could be classified as safest for all types of oxygen service.
Submerged nozzle design for SL-3 260-inch solid propellant rocket engines
Flow characteristics about submerged rocket nozzle model immersed in simulated exhaust gas
Scale model compressed air tests of 260-inch solid rocket with submerged nozzle to determine exhaust flow velocity and direction in annular channel
Submerged nozzle for solid rockets, noting exhaust flow velocity and direction determination