Search NASA⌕ Search

Engineering topics

Peng, Xuan

Publications and source records attributed to Peng, Xuan.

At least 19 records

Recent Progress in Developing Nb 3 Sn Conductors With Increased Specific Heat

A possible approach to reducing Nb 3 Sn magnet training is to increase the energy margin of Nb 3 Sn conductors by enhancing their specific heat (C p ). For this study, we have been developing Nb 3 Sn conductors with increased C p by incorporating substances with high C p at 2-10 K based on a conductor design that is compatible with standard Nb 3 Sn strand production. In the past couple of years our efforts have been mainly focused on improving strand design (e.g., position of high- C p filaments, thickness of the Cu tube for the high-C p filaments, ratio of the Cu powder to the high-C p substance, filament spacing, etc.) in order to obtain good strand drawability and to reduce degradation after rolling, which is needed for production of Rutherford cables. We also tried a new high-C p substance, Gd 2 O 2 S, and verified that it has much higher C p over the whole magnetic field range than the Gd 2 O 3 we used before. With that development work we can now produce high-C p strands with good drawability and low levels of degradation after rolling. This paper reports our findings and the current status of the development of high-C p Nb 3 Sn conductors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

High Critical Current Density in Internally-oxidized Nb 3 Sn Superconductors and its Origin

In this paper, we report achievement of non-Cu-matrix critical current density $(J_c)$ in internally-oxidized Nb 3 Sn superconductors that surpasses the best state-of-the-art Nb 3 Sn and the $J_c$ specification of the Future Circular Collider. We then explore the mechanism of the improvement, which was believed to be caused by refined grain size. However, our experiment showed that even with similar grain size, internally-oxidized wires had significantly higher $J_c$ than non-oxidized wires. This, combined with transmission electron microscopy and atom probe tomography studies which showed a high density of intragranular nano-precipitates with suitable sizes as pinning centers in internally-oxidized wires, demonstrates a significant contribution from the nano-precipitates.

43 PARTICLE ACCELERATORS↗

Development and Study of Nb 3 Sn Wires With High Specific Heat

Recently, a new type of Nb 3 Sn conductors were developed, which, by incorporating substances with high specific heat at 2-8 K in a proper design, have demonstrated significant improvement of minimum quench energy (MQE). This method to improving energy margins of conductors is promising to reduce Nb 3 Sn magnet training. Here, we continue studying this type of conductors. Voltage-current (V-I) measurements from 15 T to 0 T and voltage-field (V-B) sweeps at various currents were conducted to investigate the influence of increased specific heat on the intrinsic stability of Nb 3 Sn conductors. Normal zone propagation velocity (NZPV) was also studied. Lastly, a new scheme was put forward to introduce a new type of substances with not only high specific heat but also high thermal diffusivity to Nb 3 Sn conductors, which is expected to work more effectively.

43 PARTICLE ACCELERATORS↗

Ternary Nb 3 Sn superconductors with artificial pinning centers and high upper critical fields

In this letter we demonstrate the development of ternary Nb3Sn multifilamentary conductors with artificial pinning centers (APC) which achieve high critical fields. These recently-developed conductors were tested in a 31 T magnet, and the results showed that their upper critical field ( B c2 ) values at 4.2 K are 27-28 T, and irreversible field ( B irr ) values are above 26 T, values similar to or higher than those of best RRP conductors. The non-Cu J c has been brought to nearly 1200 A/mm –2 at 16 T and 4.2 K, comparable to RRP, in spite of the fact that the fine-grain Nb 3 Sn fractions in filaments are still low (20-30%) and the grain sizes are still not fully refined (70-80 nm) due to conductor designs and heat treatments that are not yet optimized. The Nb 3 Sn layer J c at 4.2 K, 16 T is 4710 A/mm –2 for the APC wire with 1% Zr, about 2.5 times higher than RRP conductors, in spite of the fact that its grain size is not yet fully refined due to insufficient oxygen and unoptimized heat treatment. An analysis is presented about the non-Cu J c that can be achieved by further optimizing the APC conductors and their heat treatments.

43 PARTICLE ACCELERATORS↗

Superconducting wires and methods of making thereof

Disclosed herein are superconducting wires. The superconducting wires can comprise a metallic matrix and at least one continuous subelement embedded in the matrix. Each subelement can comprise a non-superconducting core, a superconducting layer coaxially disposed around the non-superconducting core, and a barrier layer coaxially disposed around the superconducting layer. The superconducting layer can comprise a plurality of Nb.sub.3Sn grains stabilized by metal oxide particulates disposed therein. The Nb.sub.3Sn grains can have an average grain size of from 5 nm to 90 nm (for example, from 15 nm to 30 nm). The superconducting wire can have a high-field critical current density (J.sub.c) of at least 5,000 A/mm.sup.2 at a temperature of 4.2 K in a magnetic field of 12 T. Also described are superconducting wire precursors that can be heat treated to prepare superconducting wires, as well as methods of making superconducting wires.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Recent Progress in Application of Internal Oxidation Technique in Nb3Sn Strands

The internal oxidation technique can generate ZrO2 nano particles in Nb3Sn strands, which markedly refine the Nb3Sn grain size and boost the high-field critical current density (Jc). This article summarizes recent efforts on implementing this technique in practical Nb3Sn wires and adding Ti as a dopant. It is demonstrated that this technique can be readily incorporated into the present Nb3Sn conductor manufacturing technology. Powder-in-tube (PIT) strands with fine subelements (~25 µm) based on this technique were successfully fabricated, and proper heat treatments for oxygen transfer were explored. Future work for producing strands ready for applications is proposed.

43 PARTICLE ACCELERATORS↗