Engineering topics
Publications and source records attributed to Penn, B..
Pyroelectric and dielectric properties of modified PZT and PZ have been studied for their use in infrared detectors. Various material figure-of-merits for their use in infrared detector are calculated including when the pyroelectric element is placed on heat-sink condition. The results are compared with exiting candidate materials.
We report the study of a Fabry-Perot electro-optical modulator using thin crystalline film NPP, and Crystalline LiNbO3. We are able to observe 14, and 60 percent degree of modulation. Measurements were carried using a standard lock-in amplifier with a silicon detector. The proposal to design a Fabry-Perot electro-optic modulator with an intracavity electro-optically active organic material was based on the initial results using poled polymer thin films. The main feature of the proposed device is the observation that in traditional electrooptic modulators like a Packets cell, it requires few kilovolts of driving voltage to cause a 3 dB modulation even in high figure-of-merit electrooptic materials like LiNbO3. The driving voltage for the modulator can be reduced to as low as 10 volts by introducing the electrooptic material inside die resonant cavity of a Fabry-Perot modulator. This is because the transmission of the Fabry-Perot cavity varies nonlinearly with the change of refractive index or phase of light due to applied electric field.
A picosecond switch made of polydiacetylene thin film coated on the interior of a 50-micron diameter hollow fiber and a nanosecond switch made of a micron thick film of phthalocyanine on glass were developed.
The research to design a Fabry-Perot electrooptic modulator with an intracavity electrooptically active organic material is based on the initial results of Wang et. al. using poled polymer thin films. The main feature of the proposed device is the observation that in traditional electrooptic modulators like a Pockels cell, it requires few kilovolts of driving voltage to cause a 3 dB modulation even in high figure-of-merit electrooptic materials like LiNbO3. The driving voltage for the modulator can be reduced to as low as 10 volts by introducing the electrooptic material inside the resonant cavity of a Fabry-Perot modulator. This is because the transmission of the Fabry-Perot cavity varies nonlinearly with the change of refractive index or phase of light due to applied electric field. We describe in this report the progress made so far in the design and fabrication of the proposed device.
The research to design a Fabry-Perot electrooptic modulator with an intracavity electrooptically active organic material is based on the initial results of Wang et. al. [1] using poled polymer thin films. The main feature of the proposed device is the observation that in traditional electrooptic modulators like a Pockels cell, it requires few kilovolts of driving voltage to cause a 3 dB modulation even in high figure-of-merit electrooptic. materials like LiNbO3. The driving voltage for the modulator can be reduced to as low as 10 volts by introducing the electrooptic material inside the resonant cavity of a Fabry-Perot modulator. This is because the transmission of the Fabry-Perot cavity varies nonlinearly with the change of refractive index or phase of light due to applied electric field. We describe in this report the progress made so far in the design and fabrication of the proposed device.
An electrooptic modulator using a thin slice of LiNbO3 within the cavity of a Fabry-Perot interferometer is designed and fabricated. The modulator is operated with 633 nm light from a He-Ne laser. Results related to characterization of this modulator are presented.
Phthalocyanine (Pc) films have been synthesized by vapor deposition on quartz substrates, some of which were coated with a very thin gold film before depositing Pc films. Electrical fields up to 6200 V/cm between a mech electrode and the substrate are introduced during film growth. These films have been characterized by x-ray diffraction and scanning electron microscopy. The molecular orientations and surface morphology of Pc films were changed under the electrical fields. The surface of these films grown without electrical field shows whisk-like morphology. When films are deposited under an electrical field, a dense film with flat surface is obtained.
Ion implantation has been shown to produce a high density of metal colloids within the layer regions of glasses and crystalline materials. The high-precipitate volume fraction and small size of metal nanoclusters formed leads to values for the third-order susceptibility much greater than those for metal doped solids. This has stimulated interest in use of ion implantation to make nonlinear optical materials. On the other side, LiNbO3 has proved to be a good material for optical waveguides produced by MeV ion implantation. Light confinement in these waveguides is produced by refractive index step difference between the implanted region and the bulk material. Implantation of LiNbO3 with MeV metal ions can therefore result into nonlinear optical waveguide structures with great potential in a variety of device applications. We describe linear and nonlinear optical properties of a waveguide structure in LiNbO3-based composite material produced by silver ion implantation in connection with mechanisms of its formation.
An optical limiter is a device which exhibits a decrease in the transmittance in a material with an increase in intensity of light. Sol-gel techniques offer many advantages in the fabrication of materials. These materials possess many desirable properties for nonlinear optical (NLO) device applications which include transparency, high thermal and chemical stabilities, very low refractive index and dielectric constants. C60 shows a higher excited state absorption cross section than the ground state absorption cross section over the complete visible spectrum, and the spectrum of the excited state absorption of C60 has the same general shape as the ground state absorption. This fact suggests that fullerenes are ideal optical limiting materials. Aerogels are fabricated by sol-gel processing. One of the key issues is the dispersion of fullerenes into small and uniform pores of silica aerogel host matrices. The aerogel network was characterized by Raman spectroscopy. Atomic force microscopy is a technique with many advantages to characterize the aerogel materials. The morphology of the cleaved surface for a C60/aerogel sample shows that there are long paralleled shaped stripes with 20-30 nm in width and about 500 nm in length on the cleaved surface. The cleaved surface also was etched by 5% HF solution for one minutes, and it became smoother after HF etching. The main feature in on the surface is the spherical particles with the size of few nanometers, and no aggregated fullerenes appear. The fullerenes are well dispersed in the aerogel matrices.
Jib ensures layers of fiber-reinforced preimpregnated tape correctly oriented in assembly of composite panels. Jig enables fast and reproductible alinement of fibers in multiaxis layups.
Process suitable for production of silicon nitride/silicon carbide fibers. High-tensile-strength silicon carbide/silicon nitride fibers prepared by pyrolyzing fibers drawn from melt of polycarbosilazane resin. Such fibers show promise as replacements for carbon fibers in high-strength composites for automotive, aerospace, and other applications where high electrical conductivity of carbon fibers makes them unsuitable.
Silicon nitride/silicon carbide fibers prepared by pyrolysis of polycarbosilazanes proposed substitute for carbon fibers. Silicon nitride/silicon carbide fibers tested pyrolyzed from polycarbosilazanes prepared from tris(N-methylamino) methylsilane. Polycarbosilazane resin drawn into fiber from melt, treated and pyrolyzed. Pyrolyzed fibers are shiny black. Tests show new fibers have physical properties comparable to graphite but with lower conductivity.
Polyurethane adhesive bonds strain gages reliably to graphite/epoxy composites. Adhesive easy to apply, used over wide temperature range (ambient to cryogenic), and applied in short time. Tests on gages bonded to composite with adhesive demonstrated reliability of attachment.
Empirical equation predicts thermal conductivity of composite insulators consisting of cellular, granular or fibrous material embedded in matrix of solid viscoelastic material. Application in designing custom insulators for particular environments.
Commercial oscillograph imparts impact energy to elastomeric materials modified to perform same function on composites.
Roller tool spreads even layer of adhesive. Tool easily constructed from metal, plastic, or wood. Sewing-thread spool serves as roller, nail as axle, and jigsawed block of wood as handle. Tool rolled and pressed against plastic film to assure even layer of adhesive around periphery.
Five samples tested in one cooldown. Holder mounted in testing machine. Submerged in cryogenic liquid held in cryostat. Movable crosshead of testing machine moves gradually downward. Samples placed under tension, one after another, starting with top one; each sample fails in turn before next is stressed.