Engineering topics

Peplov, Vladimir

Publications and source records attributed to Peplov, Vladimir.

9 records

DOE OSTI2023

Ramp Generator for Electron Scanner in SNS Beam Profile Measurements System

A new fast high voltage Ramp Generator to deflect an electron beam in the Electron Scanner is required at the Spallation Neutron Source (SNS) in the Oak Ridge National Laboratory. The Electron Scanner is used for non-destructively measuring the transverse profiles of the proton beam in the accumulator ring of the SNS [1]. The existing deflector is obsolete and needs to be replaced. A new Ramp Generator is proposed based on fast high voltage MOSFET power switches. Two configurations have been considered. One is bipolar, with two opposite polarity power supplies and one switch module or two single switches, and the other is unipolar, with one power supply and two switch modules. Schematics and performance of both options are described, and results of the prototype testing are presented in the paper.

Peplov, Vladimir↗

DOE OSTI2021

Progress in development of pulsed resonant charging power supply for the Spallation Neutron Source extraction kicker PFN system

A conceptual design of the pulsed resonant charging power supply (RCPS) for the beam extraction system of the Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory (ORNL) was previously reported at the 2019 IEEE Pulsed Power & Plasma Science Conference (PPPS 2019) [1]. Development and testing of the prototype supply continued through the year to finalize the design ahead of the Proton Power Upgrade (PPU). Testing revealed reliability issues with the original resonant charging scheme related to the step-up transformer core. Additional components were incorporated into the system, and some of the original prototype components were replaced to improve performance and reliability of the power supply. This paper describes the changes in the resonant charging scheme, presents the results of testing of the improved prototype at full power level, and shows the final design of the RCPS.

Peplov, Vladimir↗

DOE OSTI2019

Pulsed Resonant Charging Power Supply for the Spallation Neutron Source Extraction Kicker PFN System

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory uses fourteen pulsed modulators in the extraction system to deflect the proton beam from the accumulation ring to the target. Each individual pulse modulator is a pulse-forming network (PFN) located in a service building external to the ring tunnel. SNS is in the planning and development phase of a proton power upgrade (PPU) to increase the beam energy from 1.0 to 1.3 GeV, and the extraction system is required to provide the same deflection at the higher beam energy. Increasing the magnet current, by charging the PFN to a higher voltage, by 20% will provide the required deflection. The existing capacitor charging power supply is incapable of charging the PFN to higher voltages between the 60 Hz pulses; therefore, a new resonant charging scheme has been developed to charge to the PPU higher voltage within the available time. This paper describes the resonant charging power supply design and presents test results from a prototype operating on a full system test stand.

Saethre, Robert↗

DOE OSTI2019

Simulations of Beam Chopping for Potential Upgrades of the SNS LEBT Chopper

The LEBT chopper is a critical element of the SNS accelerator system. In this work, the benefit of increasing the chopping voltage amplitude for the present chopping pattern is shown with beam simulations, and an ongoing hardware upgrade of the chopper pulser units is discussed. In addition, with the prospect of higher voltage capability of the new pulser design, two alternative chopping patterns which reduce the switching frequency of the chopper pulsers down to 1/2 or 1/4 of the present chopping pattern, are also explored with beam simulations.

Han, Baoxi↗

DOE OSTI2018

Performance of High Voltage Bipolar Pulse Generator with Fast Push-Pull Solid-State Switch Modules

Four identical pulse generators (pulsers) provide fast beam deflection in the Low Energy Beam Transport (LEBT) beam chopping system at the Spallation Neutron Source (SNS) Linac. The existing pulsers have become obsolete and need to be replaced to improve overall performance of the chopper system. A new bipolar pulse generator has been designed, and a prototype has been built and tested at the SNS. The generator uses fast push-pull transistor BEHLKE switch modules. It can produce a 1MHz burst of alternate 2.5kV with adjustable pulse widths during the 1-ms macro-pulse at a burst repetition frequency of 60Hz with rise/fall times of less than 40ns into a 100pF capacitive load. The performance enhancements of this new pulser in comparison with existing and previous versions of the pulse generator are discussed in the paper. The pulser can be used in applications requiring a series of bipolar ±3.5kV pulses, or unipolar pulses of positive or negative polarity with amplitude up to 4.5kV and various pulse widths with a minimum of 150ns. The maximum switching frequency, number of pulses, or burst repetition frequency in burst mode is limited by maximum power dissipation in the switches and other components. The features of this new pulser along with the results of timing control adjustments, timing and temperature measurements, and HV full power testing on the test stand are presented.

Peplov, Vladimir↗

DOE OSTI2018

ALTERNATIVE CONFIGURATION AND TIMING CONTROL FOR BEAM CHOPPING SYSTEM AT THE SNS LINAC

The Spallation Neutron Source (SNS) beam chopping system uses a segmented electrostatic lens in the Low Energy Beam Transport (LEBT) line to deflect the beam out of the Radio Frequency Quadrupole (RFQ) input aperture to create gaps in the 1 ms beam macro-pulse for extraction from the Ring, or fully displace the beam. The lens is split azimuthally into four quadrants which are pulsed independently by four bipolar high voltage pulse generators. The chopper timing control system creates trigger pulses to the pulse generators which deflect the beam sequentially to four positions on the chopper target. In the present chopper configuration, all four segments are powered simultaneously with a 1 MHz burst repetition rate within the macro-pulse. To improve chopping performance, faster switches and higher voltages are required. An alternative chopping system configuration which can meet this request has been proposed, where only two opposite segments are used at a time. This will facilitate pulse generator performance by reducing switching frequency and power dissipation in the high voltage switches while operating at increased voltages, and make beam deflection more effective, stable and reliable. The new chopping configuration requires changes in the LEBT timing control patterns, upgrading the pulse generator, and changing the azimuthal position of the lens segments in the LEBT structure.This paper will review the timing control patterns for present and suggested configurations, compare the pulse generator performance for both cases, and show the advantages of the new chopping modes. The results of the simulated beam distribution at the RFQ input for different deflecting voltages will also be presented.

Peplov, Vladimir↗

DOE OSTI2017

Pulse Generator for Beam Deflector at the SNS Beam Test Facility

A new Beam Test Facility (BTF) has been built at the Spallation Neutron Source (SNS). It contains an ion source, Low Energy Beam Transport (LEBT) system, and a new Radio Frequency Quadrupole (RFQ) cavity. To determine the transmission losses of the ion beam through the RFQ, beam currents at RFQ input and output have to be measured. Input current measurements can be performed with an electrostatic deflector within the LEBT to displace the beam to a current pick up sensor located radially outward from the beam axis. A new pulse generator has been designed and built at the SNS to produce up to 6 kV pulses, with a pulse width of 1 to 10 usec at a repetition frequency of 10 Hz into the capacitive load to create the appropriate deflecting electrical field. This paper will review the beam deflector system; describe the new pulse generator and its performance, and present preliminary results of the beam transmission measurements.

Peplov, Vladimir↗

DOE OSTI2017

A New 2.5 MeV Injector and Beam Test Facility for the Spallation Neutron Source

The U.S. Spallation Neutron Source (SNS) now operates with 1.2 MW of beam power on target with the near-term goal of delivering 1.4 MW and a longer-term goal of delivering >2 MW to support a planned second target station. Presently, H- beam pulses (50-60 mA, 1 ms, 60 Hz) from an RF-driven, Cs-enhanced, multi-cusp ion source are first accelerated to 2.5 MeV by a Radio Frequency Quadrupole (RFQ) accelerator, injected into a ~1 GeV linac, compressed to <1μs in an accumulator ring and ultimately delivered to a liquid mercury target for pulsed neutron production. In recent years concerns about the RFQ performance has motivated the procurement of a new RFQ and the creation of a Beam Test Facility (BTF) to allow off-line testing. The purpose of the BTF is to first validate performance of the new RFQ before installing it in place of the existing RFQ and later to serve as a stand-alone 2.5 MeV research accelerator employing the original SNS RFQ. After validating the new RFQ with respect to energy, emittance and transmission, the initial applications of the BTF will be to conduct 6D beam dynamic studies, develop & demonstrate ion sources capable of meeting the current and future requirements of the SNS, and contribute to neutron moderator development. This report provides a facility update, description of the BTF ion source systems as well as a discussion of the first LEBT and RFQ beam current measurements performed at the BTF.REFERENCES

Welton, Robert F.↗

DOE OSTI2017

Development of a 100 kV pulse generator for driving an electron scanner used in proton beam profile measurements

The Spallation Neutron Source (SNS) utilizes an electron scanner in the accumulator ring for nondestructive transverse profiling of the proton beam. The electron scanner consists of a high voltage pulse generator driving an electron gun, a medium voltage ramp generator, and a CCD camera. A new high voltage pulse generator that provides negative 100 kV pulses with rise times of less than 200 ns, +/-0.5% flattop of greater than 100 ns has been designed, delivered, and undergone extensive testing. The pulse generator has been operationally verified with the existing control system and simulated loads. Full system testing with the actual electron scanner is planned. This paper details the requirements, design, setup, and test results of the high voltage pulse generator.

Morris, B↗