Engineering topics
Perera, Inosh
Publications and source records attributed to Perera, Inosh.
Photocatalytic degradation of orange II dye via high pore volume polymorph zirconium-doped titania under visible light irradiation
A series of mixed-phase Zr-doped TiO 2 was utilized for the photocatalytic degradation of orange II dye. These materials were synthesized through a sol–gel technique by varying the amounts of zirconium in the photocatalysts. These materials were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray fluorescence (XRF), Raman spectroscopy, thermogravimetry analysis (TGA), and X-ray photoelectron spectroscopy (XPS) among others. XRF and XPS data showed that the elemental composition of the photocatalysts consists of zirconium, titanium, and oxygen. In addition, XRD and Raman spectroscopy confirmed the existence of anatase and rutile phases of TiO 2 . The TGA analyses showed that the undoped TiO 2 was the most stable, with no significant weight loss during the heating range. Furthermore, the materials can effectively degrade orange II dye solution up to 7 cycles through asymmetric cleavage of the azo bond.
Stoichiometric metal nitration based novel green synthesis of mesoporous metal oxides and their enhanced heterogeneity
Here, in this work, a general and novel method for the green synthesis of mesoporous metal oxides via stoichiometric metal nitration has been demonstrated. Pluronic surfactants and their effect on synthesis procedures in terms of surface area have been experimentally studied in detail. Contrary to the traditional synthesis procedure, water has been utilized as the solvent and in several cases, such as tin oxide, manganese oxide, aluminum oxide, antimony oxide, zinc oxide, cobalt oxide, copper oxide, yttrium oxide, lanthanum oxide, and silver either the highest or comparable surface areas have been successfully synthesized. Through XRD, and TEM, all materials were observed to be crystalline except silver and magnesium oxide. SEM shows that with an increase in surfactant molar mass agglomeration decreases. Ammonia chemisorption on acidic materials gives quantitative amounts of ammonia chemical bonding with catalysts, whereas carbon dioxide chemisorption gives a quantitative value of CO 2 chemical binding with basic sites. As high as 1901.8 μmol/g and 994.6 μmol/g ammonia chemisorption values for oxides of vanadium and tin were achieved. Amphoteric materials give both acidic and basic enhanced adsorption. Finally, all synthesized materials are studied under organic catalytic transformations. Benzyl bromide is theoretically more active compared with benzylamine and benzyl alcohol which was also experimentally shown through the conversion.
Partial oxidation of methane to methanol on boron nitride at near critical acetonitrile
Abstract Direct catalytic conversion of methane to methanol with O 2 has been a fundamental challenge in unlocking abundant natural gas supplies. Metal-free methane conversion with 17% methanol yield based on the limiting reagent O 2 at 275 °C was achieved with near supercritical acetonitrile in the presence of boron nitride. Reaction temperature, catalyst loading, dwell time, methane–oxygen molar ratio, and solvent-oxygen molar ratios were identified as critical factors controlling methane activation and the methanol yield. Extension of the study to ethane (C2) showed moderate yields of methanol (3.6%) and ethanol (4.5%).
Selenium-doped copper oxide nanoarrays: Robust electrocatalyst for the oxygen evolution reaction with ultralow overpotential
The oxygen evolution reaction (OER) is the key anodic reaction in electrochemical water splitting. OER is a four-electron process with sluggish reaction kinetics. RuO 2 and IrO 2 are the benchmark catalysts for OER. Thus, finding a low-cost, earth-abundant, and stable electrocatalyst for OER is a big challenge. Here in this work, we report OER over Se-CuO/CF nanoarrays with an ultralow overpotential of 440 mV (at 50 mA/cm 2 current density). Se-CuO/CF nanoarray has a TOF of 0.05 s -1 at 300 mV. The catalyst showed consistent OER performance upto1000 cycles run over a period of 10 h. The OER performance of Se-CuO/CF nanoarrays was compared with RuO 2 /CF catalyst and the overpotential for RuO 2 /CF nanoarray was only 10 mV lower than Se-CuO/CF 50 mA/cm 2 current density. Se-CuO/CF nanoarray showed 50 mV lower overpotential than the state of the art RuO 2 /CF catalyst at a current density of 100 mA/cm 2 . The Tafel slope of Se-CuO/CF is 21 mV/decade lower compared to RuO 2 /CF suggesting faster reaction kinetics of Se-CuO/CF. The electrochemical surface area and the conductivity were increased upon doping Se into CuO/CF nanoarrays which can be attributed to enhanced OER performance of the Se-CuO/CF nanoarrays.
Partial oxidation of isobutylene using Ni TiO x
In this work, we report an aerobic partical oxidation of isobutylene into isoprene, acetone, and p-xylene using a mesoporous Ni TiO x catalytic material. In this work, two catalysts were found to synthesize two of these three valuable products with high selectivity, with p-xylene being synthesized with a selectivity of 46.0% and isoprene being synthesized with a selectivity of 64.7%, with overall conversions of isobutylene being 34.0% and 11.9% respectively. These reactions were done at relatively low temperatures. (300°C or below) and are conducted at flow rates of 10 sccm oxygen and isobutylene. The nickel titania catalysts were studied extensively using various characterization methodologies such as TEM, Raman, XRD, and XRF.
Mesoporous Crystalline Niobium Oxide with a High Surface Area: A Solid Acid Catalyst for Alkyne Hydration
A mesoporous crystalline niobium oxide with tunable pore sizes was synthesized via the sol–gel-based inverse micelle method. The material shows a surface area of 127 m 2 /g, which is the highest surface area reported so far for crystalline niobium oxide synthesized by soft template methods. The material also has a monomodal pore size distribution with an average pore diameter of 5.6 nm. A comprehensive characterization of niobium oxide was performed using powder X-ray diffraction, Brunauer–Emmett–Teller, thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, UV–vis, and X-ray photoelectron spectroscopy. The material acts as an environmentally friendly, solid acid catalyst toward hydration of alkynes under with excellent catalytic activity (99% conversion, 99% selectivity, and 4.39 h –1 TOF). Brønsted acid sites present in the catalyst were found to be responsible for the high catalytic activity. Lastly, the catalyst was reusable up to five cycles without a significant loss of the activity.