Search NASA⌕ Search

Engineering topics

Perez, Emmanuel

Publications and source records attributed to Perez, Emmanuel.

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗

Laser weld-induced formation of amorphous Mn–Si precipitate in 304 stainless steel

In this paper, we report the formation of partially amorphous Mn-Si precipitates due to laser welding of face centered cubic (fcc) 304 stainless steel. Transmission electron microscopy and precession electron diffraction studies in the heat affected zone (HAZ) of the weldment indicate the formation of these precipitates in grain interiors. Precipitates have MnSi stoichiometry and the partially crystalline regions have a lattice constant of 0.45 nm. It is surmised that the rapid cooling rates during the laser weld melt pool solidification process may be sufficient to inhibit the complete crystallization of these precipitates.

304 stainless steel↗

Elevated temperature tensile tests on DU–10Mo rolled foils

We report that studies were completed to obtain tensile mechanical properties for uranium-10wt.% molybdenum (U-10Mo) foils which were subjected to four different thermomechanical processing conditions. U-Mo alloy foils are being investigated to support fuel conversion of high power research reactors from their current high enriched fuel form to a low enriched fuel form. Mechanical properties of the fuel foil have an effect on irradiation performance and fuel fabrication and therefore are required to support modeling and qualification of new low-enriched uranium monolithic fuel plate designs. The data contained in this document contributes to fuel qualification by fulfilling the requirement that physical properties related to fuel meat be established. It is expected that depleted uranium-10wt% Mo (DU–10Mo) mechanical behavior is representative of the low-enriched U10-Mo to be used in actual fuel plates; therefore DU–10Mo was studied to simplify material processing, handling, and testing requirements. In this report, the different thermomechanical treatments included variations of wrought hot and cold rolling reduction and post rolling annealing. Each of the four foils was hot rolled. After hot rolling reduction, three of the four foils were further reduced by cold rolling. One of the three was reduced a further 20% by cold rolling, and the remaining two were reduced 50% by cold rolling. Following cold rolling reduction, one of the two foils which had been reduced 50% by cold rolling was annealed at 650?°C. Performing this analysis allows assessment of the impact of foil fabrication history on the resultant tensile properties DU–10Mo fuel foils. Tensile properties of DU–10Mo at room temperature through approximately 400 °C determined from the tests conducted herein suggest the material is stronger and has lower ductility than what has been reported previously in the literature. The explanation for these differences has yet to be determined, but is likely related to differences in grain size and/or impurity content, and variation in fabrication history. At the highest temperatures tested (550 °C) better agreement between the values reported here and available literature was found. As expected, yield and ultimate tensile strength decreased with increasing test temperature. Generally, the yield stress for all foil processing conditions was found to be in the range of 1100 MPa for room temperature tests, and in the range of 200 MPa for tests conducted at 550 °C. Ultimate tensile stress was in the range of 1175 MPa at room temperature, decreasing to approximately 225 MPa at 550 °C. Lastly, elongation increased significantly, from 0 to 2% at room temperature to 50% or more for the tests at 550 °C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Weld Development of FeCrAl Thin-Wall Cladding for LWR Accident Tolerant Fuel

The development of new cladding materials to replace Zr-based cladding for light water reactors (LWRs) has been actively pursued with improved high-temperature oxidation resistance to significantly suppress hydrogen production from an accident such as a loss of coolant event. FeCrAl alloy with a typical composition of approximately Fe-15Cr-5Al has been selected as a candidate material because of its improved high-temperature oxidation resistance over the present LWR zircaloy cladding. As a result of higher thermal neutron absorption for FeCrAl alloy, the cladding wall thickness needs to be reduced by approximately half compared to that of Zircaloy cladding to be comparable to the current LWR fuel performance under the normal operating condition. New weld techniques for joining the endplug to thin-walled cladding need to be developed. Both laser beam weld and pressure resistance weld were employed. This paper summarizes the recent progress on the laser weld development for FeCrAl cladding with 350 µm wall thickness. The results of microstructural characterization and mechanical property testing of the weld for the cladding-endplug set are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status Report on Pressure Resistance Weld Development for FeCrAl Thin-Wall Cladding

This report summarizes the recent development on the weld techniques of joining the thin walled FeCrAl cladding to the endplug as a part of accident tolerant fuels (ATF) program for advanced light water reactor (LWR) systems. The FeCrAl alloy has been considered as the top candidate cladding materials for ATF fuels largely due to its high oxidation resistance in high temperature steam relevant to the loss of coolant accident (LOCA) conditions. The two primary techniques for the thin-walled cladding weld development are laser beam weld (fusion based) and pressure resistance weld (solid state without melting). This report focuses on the progress made on the pressure resistance weld (PRW) development for a commercial FeCrAl alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Temperature Fuel Cladding Chemical Interactions Between TRIGA Fuels and 304 Stainless Steel

High-temperature fuel-cladding chemical interactions (FCCI) between TRIGA (Training, Research, Isotopes, General Atomics) fuel elements and the 304 stainless steel (304SS) are of interest to develop an understanding of the fuel behavior during transient reactor scenarios. TRIGA fuels are composed of uranium (U) particles dispersed in a zirconium-hydride (Zr-H) matrix. In reactor, the fuel is encased in 304-stainless-steel (304SS) or Incoloy 800 clad tubes. At high temperatures, the fuel can readily interact with the cladding, resulting in FCCI. A number of FCCI can take place in this system. Interactions can be expected between the cladding and the Zr-H matrix, and/or between the cladding and the U-particles. Other interactions may be expected between the Zr-H matrix and the U-particles. Furthermore, the fuel contains erbium-oxide (Er-O) additions. Interactions can also be expected between the Er-O, the cladding, the Zr-H and the U-particles. The overall result is that very complex interactions may take place as a result of fuel and cladding exposures to high temperatures. This report discusses the characterization of the baseline fuel microstructure in the as-received state (prior to exposure to high temperature), characterization of the fuel after annealing at 950C for 24 hours and the results from diffusion couple experiments carries out at 1000C for 5 and 24 hours. Characterization was carried out via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with sample preparation via focused ion beam in situ-liftout-technique.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Temperature Fuel Cladding Chemical Interactions Between Unirradiated TRIGA Fuels and 304 Stainless Steel

High temperature fuel cladding chemical interactions (FCCI) between Training-Research, Isotopes-General-Atomics (TRIGA) fuel elements and their 304 stainless steel (304SS) cladding are of interest to develop an understanding of the fuel-behavior during transient reactor scenarios. TRIGA fuels are composed of uranium particles dispersed in a zirconium hydride (Zr H) matrix encased in a 304SS cladding. At high temperatures, the fuel and cladding have the potential experience FCCI. A large number of interactions can take place in this multi-component fuel system. Emphasis is given to the development of low melting point phases. Diffusion couples of TRIGA fuel vs. 304SS were annealed at 1000°C for 5 and 24 hours. Characterization was then carried out via scanning electron microscopy and transmission electron microscopy. The as-received and annealed microstructures of the fuel and the interactions regions between the fuel and the 304SS will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coated U(Mo) Fuel: As-Fabricated Microstructures

As part of the development of low-enriched uranium fuels, fuel plates have recently been tested in the BR-2 reactor as part of the SELENIUM experiment. These fuel plates contained fuel particles with either Si or ZrN thin film coating (up to 1 µm thickness) around the U-7Mo fuel particles. In order to best understand irradiation performance, it is important to determine the starting microstructure that can be observed in as-fabricated fuel plates. To this end, detailed microstructural characterization was performed on ZrN and Si-coated U-7Mo powder in samples taken from AA6061-clad fuel plates fabricated at 500°C. Of interest was the condition of the thin film coatings after fabrication at a relatively high temperature. Both scanning electron microscopy and transmission electron microscopy were employed. The ZrN thin film coating was observed to consist of columns comprised of very fine ZrN grains. Relatively large amounts of porosity could be found in some areas of the thin film, along with an enrichment of oxygen around each of the the ZrN columns. In the case of the pure Si thin film coating sample, a (U,Mo,Al,Si) interaction layer was observed around the U-7Mo particles. Apparently, the Si reacted with the U-7Mo and Al matrix during fuel plate fabrication at 500°C to form this layer. The microstructure of the formed layer is very similar to those that form in U-7Mo versus Al-Si alloy diffusion couples annealed at higher temperatures and as-fabricated U-7Mo dispersion fuel plates with Al-Si alloy matrix fabricated at 500°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Results of U-xMo (x=7, 10, 12 wt.%) Alloy Versus Al-6061 Cladding Diffusion Couple Experiments Performed at 500, 550 and 600°C

The Reduced Enrichment for Research and Test Reactors (RERTR) program has been developing low enrichment fuel systems encased in Al 6061 for use in research and test reactors. U–Mo alloys in contact with Al and Al alloys can undergo diffusional interactions that can result in the development of interdiffusion zones with complex fine-grained microstructures composed of multiple phases. A monolithic fuel currently being developed by the RERTR program has local regions where the U–Mo fuel plate is in contact with the Al 6061 cladding and, as a result, the program finds information about interdiffusion zone development at high temperatures of interest. In this study, the microstructural development of diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo, and U-12wt.%Mo vs. Al 6061 (or 6061 aluminum) cladding, annealed at 500, 550, 600 degrees C for 1, 5, 20, 24, or 132 hours, was analyzed by backscatter electron microscopy and x-ray energy dispersive spectroscopy on a scanning electron microscope. Concentration profiles were determined by standardized wavelength dispersive spectroscopy and standardless x-ray energy dispersive spectroscopy. The results of this work shows that the presence of surface layers at the U–Mo/Al 6061 interface can dramatically impact the overall interdiffusion behavior in terms of rate of interaction and uniformity of the developed interdiffusion zones. It further reveals that relatively uniform interaction layers with higher Si concentrations can develop in U–Mo/Al 6061 couples annealed at shorter times and that longer times at temperature result in the development of more non-uniform interaction layers with more areas that are enriched in Al. At longer annealing times and relatively high temperatures, U–Mo/Al 6061 couples can exhibit more interaction compared to U–Mo/pure Al couples. The minor alloying constituents in Al 6061 cladding can result in the development of many complex phases in the interaction layer of U–Mo/Al–6061 cladding couples, and some phases in the interdiffusion zones of U–Mo/Al–6061 cladding couples are likely similar to those observed for U–Mo/pure Al couples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure characterization of as-fabricated and 475 Degrees C annealed U–7 wt.% Mo dispersion fuel in Al–Si alloy matrix

High-density uranium (U) alloys with an increased concentration of U are being examined for the development of research and test reactors with low enriched metallic fuels. The U-Mo fuel alloy dispersed in Al-Si alloy has attracted particular interest for this application. This paper reports our detailed characterization results of as-fabricated and annealed (475 Degrees C for 4 h) U-Mo dispersion fuels in Al-Si matrix with a Si concentration of 2 and 5 wt.%, named as As2Si, As5Si, An2Si, An5Si accordingly. Techniques employed for the characterization include scanning electron microscopy and transmission electron microscopy with specimen prepared by focused ion beam in situ lift-out. Fuel plates with Al-5 wt.% Si matrix consistently yielded thicker interaction layers developed between U-Mo particles and Al-Si matrix, than those with Al-2 wt.% Si matrix, given the same processing parameters. A single layer of interaction zone was observed in as-fabricated samples (i.e., As2Si, As5Si), and this layer mainly consisted of U3Si3Al2 phase. The annealed samples contained a two-layered interaction zone, with a Si-rich layer near the U-Mo side, and an Al-rich layer near the Al-Si matrix side. The U3Si5 appeared as the main phase in the Si-rich layer in An2Si sample, while both U3Si5 and U3Si3Al2 were identified in sample An5Si. The Al-rich layer in sample An2Si was amorphous, whereas that in sample An5Si mostly consisted of crystalline U(Al,Si)3, along with a small fraction of U(Al,Si)4 and U6Mo4Al43 phases. The influence of Si on the diffusion and reaction in the development of interaction layers in U(Mo)/Al(Si) is discussed in the light of growth-controlling mechanisms and irradiation performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Characterization of U-7Mo/Al-Si Alloy Matrix Dispersion Fuel Plates Fabricated at 500°C

The starting microstructure of a dispersion fuel plate will impact the overall performance of the plate during irradiation. To improve the understanding of the as-fabricated microstructures of U–Mo dispersion fuel plates, particularly the interaction layers that can form between the fuel particles and the matrix, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses have been performed on samples from depleted U–7Mo (U–7Mo) dispersion fuel plates with either Al–2 wt.% Si(Al–2Si) or AA4043 alloy matrix. It was observed that in the thick interaction layers, U(Al, Si)3 and U6Mo4Al43 were present, and in the thin interaction layers, (U, Mo) (Al, Si)3, U(Al, Si)4, U3Si3Al2, U3Si5, and possibly USi-type phases were observed. The U3Si3Al2 phase contained some Mo. Based on the results of this investigation, the time that a dispersion fuel plate is exposed to a relatively high temperature during fabrication will impact the nature of the interaction layers around the fuel particles. Uniformly thin, Si-rich layers will develop around the U–7Mo particles for shorter exposure times, and thicker, Si-depleted layers will develop for the longer exposure times.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗