Antimony nitride discovered by theoretical structure prediction, rapid thermal annealing, and in situ X-ray diffraction
Not Available
Engineering topics
Publications and source records attributed to Perkins, John D..
Not Available
Not Available
Metastable polymorphs--materials with the same stoichiometry as the ground state but a different crystal structure--enable many critical technologies. This work describes the development of a stabilization approach for metastable polymorphs that are difficult to achieve through other stabilization techniques (such as epitaxy or quenching) called stromataxy. Stromataxy is a method based on controlling the precursor structure during the initial stages of material growth to dictate phase formation. To illustrate this approach, we controlled the atomic layering of the precursors of ScFeO3 and stabilized the metastable P63cm phase, under conditions that previously led to the ground-state Ia3¯ bixbyite phase. Ab initio mechanistic calculations highlight the importance of the variable oxidation state of Fe and the layer stability during layer-by-layer growth. The broad applicability of a stromataxy approach was demonstrated by stabilizing this metastable phase on substrates that have previously been shown to stabilize other polymorphs under continuous growth. Stromataxy is shown as a viable option for accessing polymorphs that are close in energy, difficult to differentiate by strain, or that lack a well epitaxially matched substrate.
Nanoscale superlattices represent a compelling platform for designed materials as the specific identity and spatial arrangement of constituent layers can lead to tunable properties. A number of kinetically stabilized, nonepitaxial superlattices with almost limitless structural tunability have been reported in telluride and selenide chemistries but have not yet been extended to sulfides. Here, we present SnS-TaS 2 nanoscale superlattices with tunable layer architecture. Layered amorphous precursors are prepared as thin films programmed to mimic the targeted superlattice; subsequent low temperature annealing activates self-assembly into crystalline nanocomposites. We investigate structure and composition of superlattices comprised of monolayers of TaS 2 and 3–7 monolayers of SnS per repeating unit. Furthermore, a graded precursor preparation approach is introduced, allowing stabilization of superlattices with multiple stacking sequences in a single preparation. Controlled synthesis of the architecture of nanoscale superlattices is a critical path toward tuning their exotic properties and enabling integration with electronic, optical, or quantum devices.
Amorphous oxide semiconductor materials have demonstrated numerous advantages without compromise of electrical properties as compared to their crystalline counterparts, yet understanding of the fundamental principles allowing this has remained elusive. To study the origins of enhanced optoelectronic properties, we apply high-throughput, combinatorial sputtering, structural and spectral mapping, and computationally intensive ab initio molecular dynamics simulations with density functional theory to a ternary, post-transition metal oxide system, namely, zinc tin oxide. The deposited thin films exhibit a high figure of merit, achieving carrier densities in the range of 1019 to 1020 cm–3 and carrier mobilities up to 35 cm2/Vs. These results highlight the role of local distortions and cation coordination in determining the microscopic origins of carrier generation and transport. In particular, we identify the strong likelihood of Sn undercoordination in both Zn-poor and Zn-rich phases leading to the high carrier concentrations observed. This not only diverges from the still widespread historical indictment of oxygen vacancies controlling carrier population in crystalline oxides but also provides a comprehensive framework to describe the unique structure–property relationships using specific structural and electronic descriptors in disordered phase materials.
Ternary nitride compound semiconductors have attracted recent attention as electronic materials since their properties can be tuned by cation stoichiometry and ordering. A recently discovered example is MgZrN 2 , a ternary analog to the rock salt semiconductor ScN. MgZrN 2 has a larger bandgap and stronger dielectric response than the binary compound. Polycrystalline thin films of MgZrN 2 have been studied, but demonstration of high-quality growth is still required to establish its suitability for technological applications. Here, we report on epitaxial growth of MgZrN 2 thin films on (100) and (111) MgO substrates and (001) GaN templates. The MgZrN 2 composition is confirmed by Rutherford backscattering spectrometry, showing no oxygen in the film except for a thin surface oxide layer. Epitaxial growth results in MgZrN 2 with x-ray diffraction rocking curves with a full-width at half-maximum in the range of 0.3–3.0°, depending on the substrate. Transmission electron microscopy analysis of the MgZrN 2 film grown on a (111) MgO substrate confirms epitaxial growth and shows a sharp film/substrate interface. In-plane temperature-dependent Hall effect measurements show that the material is an n-type semiconductor with a relatively high concentration ( n 300K ≈ 10 19 –10 20 cm -3 ) of thermally activated electrons. Room-temperature transport measurements show a conductivity of 25 S cm -1 and a Seebeck coefficient of -80 μ V K -1 . Overall, these results provide an important step toward integration of rock salt MgZrN 2 with other technological nitrides for device applications.
Nitrides feature many interesting properties, such as a wide range of bandgaps suitable for optoelectronic devices including light-emitting diodes (LEDs), and piezoelectric response used in microelectromechanical systems (MEMS). Nitrides are also significantly underexplored compared to oxides and other chemistries, with many being thermochemically metastable, sparking interest from a basic science point of view. This paper reports on experimental and computational exploration of the Mg-Sb-N material system, featuring both metastable materials and semiconducting properties. Using sputter deposition, we discovered a new Mg 2 SbN 3 nitride with a wurtzite-derived crystal structure, and synthesized the antimonide-nitride Mg 3 SbN with an antiperovskite crystal structure for the first time in thin film form. Theoretical calculations indicate that Mg 2 SbN 3 is metastable and has properties relevant to LEDs and MEMS, whereas Mg 3 SbN has a large dielectric constant (28ε o ) and low hole effective masses (0.9m o ), of interest for photovoltaic solar cell absorbers. The experimental solar-matched 1.3 eV optical absorption onset of the Mg 3 SbN antiperovskite agrees with the theoretical prediction (1.3 eV direct, 1.1 eV indirect), and with the measurements of room-temperature near-bandgap photoluminescence. Furthermore, these results make an important contribution towards understanding semiconductor properties and chemical trends in the Mg-Sb-N materials system, paving the way to future practical applications of these novel materials.
Two-dimensional sulfides and their heterostructures have emerged as potentially useful materials for technological applications. Controllable self-assembly of interleaved crystalline heterostructures from designed thin-film precursors has been demonstrated in selenide and telluride chemical systems, but not yet in sulfide chemistries. Preparing such amorphous sulfide heterostructure precursors is a necessary first step toward this goal. Here, deposition of thin-film amorphous precursors for layered sulfide heterostructures by RF sputtering is presented on the example of SnS-MoS 2 . Here, a calibration process specific to the mechanisms of RF sputtering from sulfide and disulfide compound targets is established. Precursor film structure and composition are confirmed via x-ray reflectivity and Rutherford backscattering measurements. Local nanostructure and composition are also examined by electron microscopy and electron energy loss spectroscopy.
Combinatorial experiments involve synthesis of sample libraries with lateral composition gradients requiring spatially-resolved characterization of structure and properties. Here, due to maturation of combinatorial methods and their successful application in many fields, the modern combinatorial laboratory produces diverse and complex data sets requiring advanced analysis and visualization techniques. In order to utilize these large data sets to uncover new knowledge, the combinatorial scientist must engage in data science. For data science tasks, most laboratories adopt common-purpose data management and visualization software. However, processing and cross-correlating data from various measurement tools is no small task for such generic programs. Here we describe COMBIgor, a purpose-built open-source software package written in the commercial Igor Pro environment, designed to offer a systematic approach to loading, storing, processing, and visualizing combinatorial data sets. It includes (1) methods for loading and storing data sets from combinatorial libraries, (2) routines for streamlined data processing, and (3) data analysis and visualization features to construct figures. Most importantly, COMBIgor is designed to be easily customized by a laboratory, group, or individual in order to integrate additional instruments and data-processing algorithms. Utilizing the capabilities of COMBIgor can significantly reduce the burden of data management on the combinatorial scientist.
ZnGeN 2 offers a low-cost alternative to InGaN with the potential for band-gap tuning to span the green gap using cation site ordering. The addition of oxygen on the anion site creates an additional degree of electronic tunability. Here, we investigate the structure and optoelectronic properties of an epitaxial ZnGeN 2-x O x thin film library grown by combinatorial co-sputtering on c-Al 2 O 3 . Samples exhibit x-ray diffraction patterns and x-ray pole figures characteristic of a wurtzite (cation-disordered) structure with the expected sixfold in-plane symmetry. Transmission electron microscopy reveals a semicoherent interface with periodic dislocations that relieve strain from the large lattice mismatch and also confirms the in-plane and out-of-plane crystallographic orientation. Room-temperature photoluminescence exhibits peaks between 2.4 and 2.8 eV which are consistent with a sharp absorption onset observed by UV-vis spectroscopy. These results demonstrate low-cost synthesis of optically active yet cation disordered ZnGeN 2-x O x , indicating a path toward application as a blue-green emitter.
Synthesis and characterization of Mg x Zr 2– x N 2 (0.5 ≤ x ≤ 1.8) thin films deposited by reactive magnetron co-sputtering in nitrogen plasma is reported. Composition measurements show that nitrides with low oxygen content (less than 1%) can be formed up to x = 1.0, at which point an increase in oxygen content is observed. Up to composition of x > 1.6 the Mg x Zr 2– x N 2 thin films form in a rocksalt-derived crystal structure, as revealed by X-ray diffraction measurements. At x > 1.6 the films rapidly oxidize. The lattice constant of the stoichiometric MgZrN 2 composition is a = 4.537 Å, and only small changes in lattice parameter are observed with changing composition. Electrical conductivity decreases by several orders of magnitude with increasing Mg-content. The conductivity of Mg-rich (x ≥ 1) films increases with increasing measurement temperature, indicating semiconducting character of Mg-rich Mg x Zr 2– x N 2 . As a result, optical absorption measurements of these Mg-rich samples show a clear absorption onset at 1.8 eV, also indicative of semiconducting behavior.
Not Available
A wide variety of brookite TiO 2 synthesis methods have been published over the past several decades, but few studies discuss the underlying mechanism that stabilizes brookite over its stable counterparts, rutile and anatase. Here in this study, we investigate of the effect of pulsed laser deposition parameters on the as-deposited amorphous precursor titania thin films, which subsequently crystallize into stable and metastable TiO 2 polymorphs upon annealing. We find that oxygen pressure in the deposition chamber strongly influences the non-equilibrium state of the amorphous precursor, which ultimately allows for selective polymorph formation. Rutile forms as the dominant phase at low pO 2 < 0.1 mTorr, while anatase is favored at high pO 2 > 5 mTorr. Brookite forms primarily at intermediate pO 2 (0.5-1.0 mTorr). Controlling the amorphous structure (i.e. Ti - O bonding and polyhedral arrangement) of the precursors via oxygen deficiency is therefore likely for the selective formation of crystalline TiO 2 polymorphs from sub-stoichiometric amorphous precursors. Lastly, directing phase selectivity by manipulating the structure and internal energy of the precursor amorphous state may have tremendous potential for synthesis of metastable crystalline phases that exhibit more desirable properties in comparison to their stable counterparts.
Emerging photovoltaic materials need to prove their viability by demonstrating excellent electronic properties. In ternary and multinary semiconductors, disorder and off-stoichiometry often cause defects that limit the potential for high-efficiency solar cells. We report on Zn-rich ZnSnN 2 (Zn/(Zn + Sn) = 0.67) photoluminescence, high-resolution X-ray diffraction, and electronic structure calculations based on Monte-Carlo structural models. The mutual compensation of Zn excess and O incorporation affords a desirable reduction of the otherwise degenerate n-type doping, but also leads to a strongly off-stoichiometric and disordered atomic structure. It is therefore remarkable that we observe only near-edge photoluminescence from well-resolved excitons and shallow donors and acceptors. Based on first principles calculations, this result is explained by the mutual passivation of Zn Sn and O N defects that renders both electronically benign. The calculated bandgaps range between 1.4 and 1.8 eV, depending on the degree of non-equilibrium disorder. The experimentally determined value of 1.5 eV in post-deposition annealed samples falls within this interval, indicating that further bandgap engineering by disorder control should be feasible via appropriate annealing protocols.
The ability of a material to adopt multiple structures, known as polymorphism, is a fascinating natural phenomenon. Various polymorphs with unusual properties are routinely synthesized by compression under positive pressure. However, changing a material's structure by applying tension under negative pressure is much more difficult. We show how negative-pressure polymorphs can be synthesized by mixing materials with different crystal structures - a general approach that should be applicable to many materials. Theoretical calculations suggest that it costs less energy to mix low-density structures than high-density structures, due to less competition for space between the atoms. Proof-of-concept experiments confirm that mixing two different high-density forms of MnSe and MnTe stabilizes a Mn(Se,Te) alloy with a low-density wurtzite structure. This Mn(Se,Te) negative-pressure polymorph has 2x to 4x lower electron effective mass compared to MnSe and MnTe parent compounds and has a piezoelectric response that none of the parent compounds have. Lastly, this example shows how heterostructural alloying can lead to negative-pressure polymorphs with useful properties - materials that are otherwise nearly impossible to make.
The use of advanced machine learning algorithms in experimental materials science is limited by the lack of sufficiently large and diverse datasets amenable to data mining. If publicly open, such data resources would also enable materials research by scientists without access to expensive experimental equipment. Here, we report on our progress towards a publicly open High Throughput Experimental Materials (HTEM) Database (htem.nrel.gov). This database currently contains 140,000 sample entries, characterized by structural (100,000), synthetic (80,000), chemical (70,000), and optoelectronic (50,000) properties of inorganic thin film materials, grouped in >4,000 sample entries across >100 materials systems; more than a half of these data are publicly available. This article shows how the HTEM database may enable scientists to explore materials by browsing web-based user interface and an application programming interface. This paper also describes a HTE approach to generating materials data, and discusses the laboratory information management system (LIMS), that underpin HTEM database. Finally, this manuscript illustrates how advanced machine learning algorithms can be adopted to materials science problems using this open data resource.
We report on the theoretical prediction and experimental realization of new ternary zinc molybdenum nitride compounds. We used theory to identify previously unknown ternary compounds in the Zn-Mo-N systems, Zn 3 MoN 4 and ZnMoN 2 , and to analyze their bonding environment. Experiments show that Zn-Mo-N alloys can form in broad composition range from Zn 3 MoN 4 to ZnMoN 2 in the wurtzite-derived structure, accommodating very large off-stoichiometry. Interestingly, the measured wurtzite-derived structure of the alloys is metastable for the ZnMoN 2 stoichiometry, in contrast to the Zn 3 MoN 4 stoichiometry, where ordered wurtzite is predicted to be the ground state. The formation of Zn 3 MoN 4 -ZnMoN 2 alloy with wurtzite-derived crystal structure is enabled by the concomitant ability of Mo to change oxidation state from +VI in Zn 3 MoN 4 to +IV in ZnMoN 2 , and the capability of Zn to contribute to the bonding states of both compounds, an effect that we define as 'redox-mediated stabilization.' The stabilization of Mo in both the +VI and +IV oxidation states is due to the intermediate electronegativity of Zn, which enables significant polar covalent bonding in both Zn 3 MoN 4 and ZnMoN 2 compounds. The smooth change in the Mo oxidation state between Zn 3 MoN 4 and ZnMoN 2 stoichiometries leads to a continuous change in optoelectronic properties - from resistive and semitransparent Zn 3 MoN 4 to conductive and absorptive ZnMoN 2 . The reported redox-mediated stabilization in zinc molybdenum nitrides suggests there might be many undiscovered ternary compounds with one metal having an intermediate electronegativity, enabling significant covalent bonding, and another metal capable of accommodating multiple oxidation states, enabling stoichiometric flexibility.
Structure-specific synthesis processes are of key importance to the growth of polymorphic functional compounds such as TiO 2 , where material properties strongly depend on structure as well as chemistry. The robust growth of the brookite polymorph of TiO 2 , a promising photocatalyst, has been difficult in both powder and thin-film forms due to the disparity of reported synthesis techniques, their highly specific nature, and lack of mechanistic understanding. In this work, we report the growth of high-fraction (~95%) brookite thin films prepared by annealing amorphous titania precursor films deposited by pulsed laser deposition. We characterize the crystallization process, eliminating the previously suggested roles of substrate templating and Na helper ions in driving brookite formation. Instead, we link phase selection directly to film thickness, offering a novel, generalizable route to brookite growth that does not rely on the presence of extraneous elements or particular lattice-matched substrates. In addition to providing a new synthesis route to brookite thin films, our results take a step towards resolving the problem of phase selection in TiO 2 growth, contributing to the further development of this promising functional material.