Engineering topics

Perkins, John N.

Publications and source records attributed to Perkins, John N..

18 records

NASA NTRS1997

Transition Effects on Heating in the Wake of a Blunt Body

A series of aerodynamic heating tests was conducted on a 70-deg sphere-cone planetary entry vehicle model in a Mach 10 perfect-gas wind tunnel at freestream Reynolds numbers based on diameter of 8.23x104 to 3.15x105. Surface heating distributions were determined from temperature time-histories measured on the model and on its support sting using thin-film resistance gages. The experimental heating data were compared to computations made using an axisymmetric/2D, laminar, perfect-gas Navier-Stokes solver. Agreement between computational and experimental heating distributions to within, or slightly greater than, the experimental uncertainty was obtained on the forebody and afterbody of the entry vehicle as well as on the sting upstream of the free-shear-layer reattachment point. However, the distributions began to diverge near the reattachment point, with the experimental heating becoming increasingly greater than the computed heating with distance downstream from the reattachment point. It was concluded that this divergence was due to transition of the wake free shear layer just upstream of the reattachment point on the sting.

Hollis, Brian R.↗

NASA NTRS1996

Comparison of Experimental and Computational Aerothermodynamics of a 70-deg Sphere-Cone

Numerical solutions for hypersonic flows of carbon-dioxide and air around a 70-deg sphere-cone have been computed using an axisymmetric non-equilibrium Navier-Stokes solver. Freestream flow conditions for these computations were equivalent to those obtained in an experimental blunt-body heat-transfer study conducted in a high-enthalpy, hypervelocity expansion tube. Comparisons have been made between the computed and measured surface heat-transfer rates on the forebody and afterbody of the sphere-cone and on the sting which supported the test model. Computed forebody heating rates were within the estimated experimental uncertainties of 10% on the forebody and 15% in the wake except for within the recirculating flow region of the wake.

Hollis, Brian R.↗

NASA NTRS1996

Hypervelocity Heat-Transfer Measurements in an Expansion Tube

A series of experiments has been conducted in the NASA HYPULSE Expansion Tube, in both CO2 and air test gases, in order to obtain data for comparison with computational results and to assess the capability for performing hypervelocity heat-transfer studies in this facility. Heat-transfer measurements were made in both test gases on 70 deg sphere-cone models and on hemisphere models of various radii. HYPULSE freestream flow conditions in these test gases were found to be repeatable to within 3-10%, and aerothermodynamic test times of 150 microsec in CO2 and 125 microsec in air were identified. Heat-transfer measurement uncertainty was estimated to be 10-15%. Comparisons were made with computational results from the non-equilibrium Navier-Stokes solver NEQ2D. Measured and computed heat-transfer rates agreed to within 10% on the hemispheres and on the sphere-cone forebodies, and to within 10% in CO2 and 25% in air on the afterbodies and stings of the sphere-cone models.

Hollis, Brian R.↗

NASA NTRS1995

Three-dimensional aerodynamic analysis of a subsonic transport high-lift configuration and comparisons with wind-tunnel test results

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potential flow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid three-dimensional flow features for several intricate geometrical regions.

Edge, D. Christian↗

NASA NTRS1995

Hypervelocity Aeroheating Measurements in Wake of Mars Mission Entry Vehicle

Detailed measurements of aerodynamic heating rates in the wake of a Mars-Pathfinder configuration model have been made. Heating data were obtained in a conventional wind tunnel, the NASA LaRC 31" Mach 10 Air Tunnel, and in a high-enthalpy impulse facility, the NASA HYPULSE expansion tube, in which air and CO2 were employed as test gases. The enthalpy levels were 0.7 MJ/kg in the Mach 10 Tunnel, 12 MJ/kg at Mach 9.8 for HYPULSE CO2 tests and 14 MJ/kg at Mach 7.9 for HYPULSE air tests. Wake heating rates were also measured on three similar parametric configurations, and forebody heating measurements were made in order to facilitate CFD comparisons. The ratio of peak wake heating to forebody stagnation point heating in the Mach 10 Tunnel varied from 7% to 15% depending on the freestream Reynolds number. In HYPULSE, the ratio was ~5% for both air and CO 2. It was observed that an increase in the ratio of forebody corner radius to nose radius resulted in a decrease in peak wake heating, and moved the peak closer to the base of the forebody. The wake flow establishment process in HYPULSE was studied, and a method was developed to determine when the wake has become fully established.

Hollis, Brian R.↗

NASA NTRS1992

Internal shock interactions in propulsion/airframe integrated three-dimensional sidewall compression scramjet inlets

The advantages and design requirements of propulsion/airframe integration for high Mach number flight are studied in terms of the 3D sidewall compression scramjet inlet. The present work addresses in a parametric fashion the inviscid effects of leading edge sweep, sidewall compression, and inflow Mach number on the internal shock structure in terms of inlet compression and mass capture. The source of the Mach number invariance with leading edge sweep for a constant sidewall compression class of inlet is identified, and a previously undocumented spillage phenomenon in a constant effective wedge angle class of inlets is discussed.

Holland, Scott D.↗

NASA NTRS1992

Two leading-edge droop modifications for tailoring stall characteristics of a general aviation trainer configuration

The high-angle-of-attack testing intended to develop leading-edge modifications for tailoring the stall characteristics of model is described. Two different leading-edge modifications are considered: a small profile leading-edge droop on the outboard 24 percent of the wing and a large profile leading-edge droop on the outboard 50 percent of the wing. Results indicate that the longitudinal stability for the unmodified and both modified configurations was good for low angle of attack, but the modified configurations exhibited neutral longitudinal stability just prior to stall. The unmodified and both modified configurations demonstrated good lateral stability characteristics for low angles of attack, but all configurations were directionally unstable for high angles of attack.

Ross, Holly M.↗

NASA NTRS1992

Analysis of hypersonic nozzles including vibrational nonequilibrium and intermolecular force effects

A computational fluid dynamics algorithm is developed for the study of high-pressure axisymmetric hypersonic nozzle flows. The effects of intermolecular forces and vibrational nonequilibrium are included in the analysis. The numerical simulation of gases with an arbitrary equation of state is discussed. Simulations for a high pressure nozzle (p(0) = 138 MPa) demonstrate that both intermolecular forces and vibrational nonequilibrium have a significant affect on the flow. These nonideal effects tend to increase the Mach number at the nozzle exit plane. Thus, they must be included in the design and analysis of high pressure hypersonic nozzles.

Canupp, Patrick W.↗

NASA NTRS1992

Leading edge sweep effects in generic three-dimensional sidewall compression scramjet inlets

A computational and experimental study of generic 3D sidewall compression inlets is conducted to examine the effects of fore and aft leading edge sweep on the internal shock structure. Inlets with leading edge sweeps of +30 deg and -30 deg with sidewall compression angles of 6 deg were tested in the NASA Langley Mach 4 air tunnel at a geometric contraction ratio of 1.87. The principal difference in performance was determined to be in the mass capture. Spillage was identified as having two components: a pressure induced component and a sweep induced component. It was found that while the direction of the leading edge sweep had a large influence on the spillage, the pressure effects were more important.

Cozart, Aaron B.↗

NASA NTRS1992

Internal Shock Interactions in Propulsion/Airframe Integrated Three-Dimensional Sidewall Compression Scramjet Inlets

The advantages and design requirements of propulsion/airframe integration for high Mach number flight have led to extensive study of the three-dimensional sidewall compression scramjet inlet in recent years. Recent research publications have indicated testing over a broad range of Mach number (2 to 18) in a variety of test gases, such as air, helium, and tetrafluoromethane. Multiple experimental techniques have been employed to obtain detailed internal shock interaction data, performance data, and inlet starting limits. Computational fluid dynamics has been effectively used for preliminary parametric studies as well as in parallel with experiments to aid in the explanation of unusual or unexpected flow phenomena. Inlets of this genre afford a relatively simple, generic geometry while producing a highly complex, three-dimensional flow field dominated by shock/shock and shock/boundary layer interactions. While the importance of the viscous effects in high speed inlet interactions is recognized, the present work addresses in a parametric fashion the inviscid effects of leading edge sweep, sidewall compression, and inflow Mach number on the internal shock structure in terms of inlet compression and mass capture. In the process, the source of the of the Mach number invariance with leading edge sweep for a constant sidewall compression class of inlet is identified, and a previously undocumented spillage phenomenon in a constant effective wedge angle class of inlets is discussed.

Holland, Scott D.↗

NASA NTRS1991

Contraction ratio effects in a generic sidewall compression scramjet inlet - A computational and experimental investigation

Computed and experimental data on a generic three-dimensional sidewall compression scramjet inlet with a leading edge sweep of 45 degrees at Mach 20 are presented. A three-dimensional Navier-Stokes code was adapted to perform preliminary parametric studies leading to the present configuration. Following the design phase, the code was then employed as an analysis tool to provide a better understanding of the flow field and the experimental static and pitot pressure data. The model possessed 240 static pressure orifices distributed on the forebody plane, sidewalls, and cowl and was tested in the 31 Inch Mach 10 facility at the NASA Langley Research Center. Pitot rakes were employed to map the entrance and exit planes. The contraction ratio was observed to have a dominant effect on the inlet shock structure and performance; these effects are the emphasis of the present report. In addition to pressure measurements, oil flows were used for further visualization and comparison with computation.

Holland, Scott D.↗

NASA NTRS1991

30 x 60 foot wind tunnel test highlights for an over-the-tail advanced turboprop configuration

This paper presents results from a recent investigation of the static aerodynamic and stability characteristics of a two-surface advanced turboprop aircraft. The conceptual design places Hamilton Standard SR-7 turboprop blades close to the horizontal and vertical tail for potential acoustic shielding. Evaluation of the data shows generally favorable effects of power on aircraft stability and control, and that lateral directional trim can be achieved with one engine inoperative. The tests did show a marked effect of the direction of propeller rotation on thrust minus drag performance.

Coe, Paul L., Jr.↗

NASA NTRS1991

Wind tunnel blockage study of a generic three-dimensional sidewall compression scramjet inlet at Mach 10

A large scale model of a generic three-dimensional sidewall compression scramjet inlet has been designed based on the results of a computational parametric study for testing in the 31-inch Mach 10 Hypersonic Wind Tunnel at the NASA Langley Research Center. In order to increase the instrumentation density in interaction regions for a highly instrumented model, it is desirable to make the model as large as possible. When the cross-sectional area of a model becomes large relative to the inviscid core size of the tunnel, the effects of blockage must be considered. In order to assess these effects, a blockage model (an inexpensive, much less densely instrumented version of the configuration) was fabricated for preliminary testing. Since it was desired to determine both the effect of the model on the performance of the wind tunnel and also to determine if the inlet would start, the model possessed a total of 32 static pressure orifices distributed on the forebody plane and sidewalls; seventeen static pressure orifices on the tunnel wall and 3 pitot probes on the model monitored the tunnel performance. This paper presents the design considerations in the development of the wind tunnel model and the blockage aspects of the effects of contraction ratio, cowl location, Reynolds number, and angle of attack.

Holland, Scott D.↗

NASA NTRS1991

Effects of vibrational nonequilibrium on axisymmetric hypersonic nozzle design

A vibrational nonequilibrium Navier-Stokes computational algorithm is used to determine the flow conditions in several existing nozzles. Vibration freezes near the throat for typical stagnation conditions in these nozzles. The freezing causes the gas to behave as though the ratio of specific heats is constant. It is shown that the thick boundary layers in hypersonic nozzles create problems in their design using classic techniques. As a result, existing nozzles such as the NASA Langley Mach 17 Nitrogen Tunnel may be underexpanded and operate with poor test section conditions. A design technique based on the Navier-Stokes equations including the effects of vibrational nonequilibrium are required for high quality flow.

Candler, Graham V.↗

NASA NTRS1990

A computational parametric study of three-dimensional sidewall compression scramjet inlets at Mach 10

A computational parametric study of three-dimensional sidewall compression scramjet inlets has been performed. The parameters considered for the study include the leading edge sweep angle, varied between 30 and 60 degrees, and the cowl position, located at the throat and at two forward positions. Additionally, the effects of laminar and turbulent boundary layers as well as adiabatic and cold wall boundary conditions are assessed. The parametric study is performed for a Mach number of 10 and a unit freestream Reynolds number of 2 x 10 to the 6th/ft at a geometric contraction ratio of 5. Comparisons among the various configurations are made in terms of the gross parameters of mass capture, throat Mach number, total pressure recovery, and area weighted internal pressure ratios, as well as more detailed flow field phenomena comparisons. The inclusion of one 0-deg sweep computation indicates that the leading edge may be swept by up to 30 deg before significant changes in the gross flow field parameters occur. It is found that a 45-deg sweep configuration provides a good compromise of mass capture, total pressure recovery, and internal compression.

Holland, Scott D.↗

NASA NTRS1990

Limitations of the method of characteristics when applied to axisymmetric hypersonic nozzle design

A design study of axisymmetric hypersonic wind tunnel nozzles was initiated by NASA Langley Research Center with the objective of improving the flow quality of their ground test facilities. Nozzles for Mach 6 air, Mach 13.5 nitrogen, and Mach 17 nitrogen were designed using the Method of Characteristics/Boundary Layer (MOC/BL) approach and were analyzed with a Navier-Stokes solver. Results of the analysis agreed well with design for the Mach 6 case, but revealed oblique shock waves of increasing strength originating from near the inflection point of the Mach 13.5 and Mach 17 nozzles. The findings indicate that the MOC/BL design method has a fundamental limitation that occurs at some Mach number between 6 an 13.5. In order to define the limitation more exactly and attempt to discover the cause, a parametric study of hypersonic ideal air nozzles designed with the current MOC/BL method was done. Results of this study indicate that, while stagnations conditions have a moderate affect on the upper limit of the method, the method fails at Mach numbers above 8.0.

Edwards, Anne C.↗

NASA NTRS1990

Mach 6 testing of two generic three-dimensional sidewall compression scramjet inlets in tetrafluoromethane

Three-dimensional sidewall compression scramjet inlets with leading edge sweeps of 30 and 70 degrees have been tested in the Langley Hypersonic CF4 Tunnel at Mach 6 and a ratio of specific heats of 1.2. The effects of cowl position, contraction ratio, and Reynolds number were investigated. The models were instrumented with 42 static pressure orifices distributed on the sidewalls, baseplate, and cowl. Schlieren movies were made of each test for flow visualization of the entrance plane and cowl region. In order to obtain an approximate characterization of the flow field, a modification to two-dimensional inviscid oblique shock theory was derived to accommodate the three-dimensional effects of leading edge sweep. This theory qualitatively predicted the reflected shock structure/sidewall impingement locations and the observed increase in spillage (flow upturning) with increasing leading edge sweep. The primary effect of moving the cowl forward is capturing the flow which would have otherwise spilled out ahead of the cowl. Increasing the contraction ratio (moving the sidewalls closer together) increases the number of internal shock reflections and hence incrementally increases the sidewall pressure distribution. Significant Reynolds number effects were noted over a small range of Reynolds number.

Holland, Scott D.↗

NASA NTRS1990

Exploratory wind tunnel investigation of the stability and control characteristics of a three-surface, forward-swept wing advanced turboprop model

The purpose of the present investigation was to parametrically study the stability and control characteristics of a forward-swept wing three-surface turboprop model through an extended angle of attack range, including the deep-stall region. As part of a joint research program between North Carolina State University and NASA Langley Research Center, a low-speed wind tunnel investigation was conducted with a three-surface, forward-swept wing, aft-mounted, twin-pusher propeller, model, representative of an advanced turboprop configuration. The tests were conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. The model parameters varied in the test were horizontal tail location, canard size, sweep and location, and wing position. The model was equipped with air turbines, housed within the nacelles and driven by compressed air, to model turboprop power effects. A three-surface, forward-swept wing configuration that provided satisfactory static longitudinal and lateral/directional stability was identified. The three-surface configuration was found to have greater longitudinal control and increased center of gravity range relative to a conventional (two-surface) design. The test showed that power had a large favorable effect on stability and control about all three axis in the post-stall regime.

Coe, Paul L., Jr.↗