Search NASA⌕ Search

Engineering topics

Perl, Emmett E.

Publications and source records attributed to Perl, Emmett E..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Patterned dielectric back contact design for GaAs thermophotovoltaic devices

-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.

14 SOLAR ENERGY↗
DOE OSTI2022

Fabrication methods for high reflectance dielectric-metal point contact rear mirror for optoelectronic devices

The patterned dielectric back contact (PDBC) structure can be used to form a point-contact architecture that features a dielectric spacer with spatially distributed, reduced-area metal point contacts between the semiconductor back not recognized contact layer and the metal back contact. In this structure, the dielectric-metal region provides higher reflectance and is electrically insulating. Reduced-area metal point contacts provide electrical conduction for the back contact but typically have lower reflectance. The fabrication methods discussed in this article were developed for thermophotovoltaic cells, but they apply to any III-V optoelectronic device requiring the use of a conductive and highly reflective back contact. Patterned dielectric back contacts may be used for enhanced sub-bandgap reflectance, for enhanced photon recycling near the bandgap energy, or both depending on the optoelectronic application. The following fabrication methods are discussed in the article: PDBC fabrication procedures for spin-on dielectrics and commonly evaporated dielectrics to form the spacer layer; methods to selectively etch a parasitically absorbing back contact layer using metal point contacts as an etch mask; methods incorporating a dielectric etch through different process techniques such as reactive ion and wet etching.

14 SOLAR ENERGY↗
DOE OSTI2022

Efficient and scalable GaInAs thermophotovoltaic devices

We report thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste-heat recovery. Here, we report the design, fabrication, and testing of large area (0.8 cm 2 ), scalable, single-junction 0.75-eV GaInAs thermophotovoltaic devices reaching an efficiency of 38.8% +/- 2.0% and an electrical power density of 3.78 W/cm 2 at an emitter temperature of 1,850 °C. Reaching such a high emitter temperature and power density without sacrificing efficiency is a direct result of combining good spectral management with an optimized cell architecture, excellent material quality, and low series resistance. Importantly, fabrication of 12 high-performing devices on a 2-in wafer is shown to be repeatable, and the cell design can be readily transferred to commercial epitaxy on even larger wafers. Further improvements in efficiency can be obtained by using a multijunction architecture, illustrated by early results for a two-junction 0.84-eV GaInPAs/0.75-eV GaInAs device.

14 SOLAR ENERGY↗
DOE OSTI2022

GaAs Thermophotovoltaic Patterned Dielectric Back Contact Devices with Improved Sub-Bandgap Reflectance

We demonstrate GaAs thermophotovoltaic (TPV) devices with a patterned dielectric back contact (PDBC) architecture, featuring a dielectric spacer between the semiconductor and back metal contact over most of the back surface for high reflectance, and metal point contacts over a smaller area for electrical conduction. In the TPV application, high sub-bandgap reflectance is needed to reflect unused sub-bandgap photons to the thermal emitter to minimize energy losses in this portion of the thermal spectrum. We explore different PDBC fabrication processes with SU-8 and SiO2 dielectric spacer layers to maximize sub-bandgap reflectance while minimizing series resistance to increase TPV conversion efficiency. We successfully demonstrate GaAs SU-8 PDBC TPV devices with 2200 degrees C blackbody-weighted sub-bandgap reflectance of 94.9% and 96.5% with and without a front metal grid, respectively. This is 0.7% and 2.3% (absolute) higher than the mean sub-bandgap reflectance of 94.2% for GaAs baseline TPV devices with 100% Au back contact with front metal grid. Lower sub-bandgap reflectance in TPV devices with front grids indicates the front grid induces light scattering leading to additional parasitic absorption in the TPV device. We also show that for higher contact coverage fractions, the PDBC reflectance cannot in general be treated by a linear interpolation using simple 1D transfer matrix method modeling and should be treated instead as a diffraction grating by solving Maxwell's equations in 3D.

energy storage↗
DOE OSTI2021

Platform for Accurate Efficiency Quantification of > 35% Efficient Thermophotovoltaic Cells

Thermophotovoltaic (TPV) devices convert thermal radiation directly into electricity using semiconductor diodes and have a variety of uses from waste heat recovery to energy storage to primary power conversion. Recent results have demonstrated promising cells nearing and surpassing 30% conversion efficiency. As TPV cells continue to increase in efficiency, they become attractive for a wider range of applications. Their efficiencies must be quantified in a standardized fashion to compare results accurately across research groups. Here, we outline and quantify the most important characteristics of an accurate and precise TPV efficiency measurement. Using a custom-built measurement apparatus that takes these characteristics into account, we report 19 cells with greater than 30% conversion efficiency and 2 cells with greater than 35% conversion efficiency. This confirms that our reported cell efficiencies are not simply those of hero cells but rather of a distribution of cells that can be produced in a consistent, high-quality process.

III-V↗
DOE OSTI2021

Trapezoidal grid fingers to reduce shadowing loss and improve short circuit current

Traditional metallic contacts on solar cells can cover a substantial portion of the device area, resulting in shadowing of light that diminishes the amount of current collected. In this paper, we developed trapezoidal electron-beam evaporated Ti/Al front grid fingers on GaAs single-junction solar cells to decrease the optical shadowing and increase the photogenerated current. Here, we observe a high fill factor of 87% at 1-Sun light intensity and we observe no degradation on the open-circuit voltage. The short-circuit current density is found to increase by 0.4 mA/cm 2 when compared to previously demonstrated electroplated Ni/Au front grid fingers, resulting in an efficiency improvement of ~0.8% absolute.

14 SOLAR ENERGY↗
DOE OSTI2021

World Record Demonstration of > 30% Thermophotovoltaic Conversion Efficiency

Thermophotovoltaic (TPV) devices are solid-state heat engines that convert thermal radiation into electricity using semiconductor diodes, and have applications in energy storage, primary power conversion, and waste heat recovery. Higher temperature emitters and wider band gap photovoltaics (PVs) generally afford higher TPV efficiencies. High temperature emitters are accessible in thermal energy storage applications. We have demonstrated a world record 31% +/- 2% TPV conversion efficiency with a 0.9 cm2 GaAs-based PV device under a 2430 °C thermal emitter, producing an electrical output power of 2.23 W. Critical to the result was the cell’s high reflectance of photon energies below the device band gap. Unlike solar PV, for which sub-band gap (SBG) light is lost, a TPV cell can reflect and recycle SBG light to the thermal emitter. The demonstration was made on a custom-built measurement platform in which a ~100 cm2 graphite thermal emitter was heated under vacuum up to 2430 °C. The TPV efficiency was evaluated by comparing the measured electrical output power of the TPV with the calorimetrically measured total net power incident on the cell. The measured TPV efficiency as a function of thermal emitter temperature was corroborated by our full system modeling predictions. As far as the authors are aware, this is the highest TPV conversion efficiency ever measured, and device improvements should yield > 40% efficiency in the near future.

27 ARPA - Advanced Research Projects Agency-Energy↗
DOE OSTI2019

Reverse Heterojunction (Al)GaInP Solar Cells for Improved Efficiency at Concentration

Mitigating series resistance is crucial to the efficiency of concentrator solar cells at high current density. Conventional AlGaInP junction designs for the top junction of III-V multijunction cells present a challenging tradeoff between series resistance on the one hand and current collection and voltage on the other hand. In this article we discuss the physics of a reverse heterojunction solar cell that aims to improve on this tradeoff by combining a high bandgap Al 0.18 Ga 0.33 In 0.49 P base and a lower bandgap (Al)GaInP emitter. The high mobility of the emitter leads to a relatively low series resistance, compared with a high bandgap homojunction cell. Furthermore, the electroluminescence spectrum shows emission peaks from both the emitter and base, leading to an open-circuit voltage that is not strictly dominated by either layer. The reverse heterojunction design is increasingly beneficial as the one-sun voltage increases.

14 SOLAR ENERGY↗