Search NASA⌕ Search

Engineering topics

Perry, Mike L.

Publications and source records attributed to Perry, Mike L..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nanocolumnar Pt:Ni Alloy Thin Films by High Pressure Sputtering for Oxygen Reduction Reaction

Self-supported nanocolumnar Pt:Ni thin films (TFs) with varying Pt:Ni atomic ratios and Pt mass loadings were produced on a microporous layer (MPL)-like surface composed of carbon particles by high pressure sputtering and examined as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cells. Cauliflower-like microstructures were observed from scanning electron microscopy imaging. Various Pt:Ni atomic ratios were obtained by simply changing the relative deposition power between Pt and Ni source and investigated by X-ray diffraction and quartz crystal microbalance analysis. Additionally, electrochemical characterization of the Pt:Ni-TF/MPL-like-layer/glassy-carbon samples was conducted through benchtop cyclic voltammetry and rotating disk electrode measurements. The electrochemically active surface area (ECSA) was found to be between 22–42 m 2 g -1 for different Pt:Ni atomic ratios. Lower Pt mass loadings exhibited a higher ECSA and the catalytic activity of all Pt:Ni ratios increased with the increase in Pt mass loading. The ORR activity of the Pt:Ni-TFs increased in the order of 3:1 < 1:1 < 1:3 with exhibiting a specific activity of 1781 μA cm -2 and mass activity of 0.66 A mg -1 for the Ni-rich film with 1:3 ratio. The catalytic performance of Pt:Ni-TFs were higher than traditional high surface area carbon supported Pt nanoparticles, elemental Pt nanorods, and Pt-Ni nanorods.

08 HYDROGEN↗
DOE OSTI2020

Microstructural Evolution and ORR Activity of Nanocolumnar Platinum Thin Films with Different Mass Loadings Grown by High Pressure Sputtering

Nanocolumnar platinum thin films (Pt-TFs) with different Pt mass loadings were grown by high pressure sputtering (HIPS) and investigated as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cell applications. Mass loading was controlled by changing the sputter deposition time. A cauliflower-like columnar microstructure was achieved by depositing the Pt-TFs onto a microporous layer (MPL)-like surface composed of carbon particles in order to mimic catalyst-coated gas diffusion electrodes. Microstructural evolution of HIPS Pt-TFs and their ORR activity were investigated. Electrochemical characterization of the nanocolumnar Pt-TFs was performed by cyclic voltammetry and rotating disk electrode measurements on Pt-TF/MPL-like-layer/glassy-carbon samples in an aqueous perchloric acid electrolyte. The electrochemically active surface area increased from 18 to 39 m 2 g –1 as the Pt mass loading was decreased. Specific activity of the films was similar (~600 μA cm –2 ) for all Pt mass loadings, due to the similar nanoparticle sizes of ~5 nm as observed by transmission electron microscopy and X-ray diffraction. Furthermore, mass activity of the films increased from 0.11 to 0.26 A mg –1 as the Pt mass loading was decreased, which is an indication of the effective Pt utilization and better access through the catalyst layer at lower Pt mass loadings.

08 HYDROGEN↗
DOE OSTI2020

Oxygen Reduction Reaction Activity of Nanocolumnar Platinum Thin Films by High Pressure Sputtering

Nanocolumnar platinum thin films (Pt-TFs) were produced by high pressure sputtering (HIPS) and investigated as oxygen reduction reaction electrocatalysts for polymer electrolyte membrane fuel cells. Conventional high-density Pt-TF prepared by low pressure sputtering was also studied for comparison. Pt-TFs were deposited on a microporous layer (MPL)-like surface composed of carbon particles to mimic catalyst-coated gas diffusion electrodes. Electron microscopy imaging revealed that HIPS Pt-TFs developed a cauliflower-like columnar microstructure, which originated from a shadowing effect during HIPS. This shadowing effect is enhanced on the rough surface of the MPL-like carbon that leads to the nano-cauliflower formation. With this approach, we also aimed to relate the catalyst performance obtained by benchtop tests directly to membrane electrode assembly test results. The electrochemically active surface area of Pt-TFs increased from 10 to 19 m 2 /g with increasing sputter pressure. Specific activity of conventional high-density and nanocolumnar films were similar at ~600 μA/cm 2 , which is likely due to their similar crystal grain sizes, >5 nm. On the other hand, mass-specific (MA) activity values increased from ~0.06 A/mgPt for conventional Pt-TF to ~0.13 A/mgPt for HIPS Pt-TFs, which is consistent with the columnar microstructure of HIPS films providing a better catalyst utilization compared to conventional Pt-TF.

08 HYDROGEN↗
DOE OSTI2020

Perspective—On the Need for Reliability and Safety Studies of Grid-Scale Aqueous Batteries

Li-ion batteries currently dominate electrochemical energy storage for grid-scale applications, but there are promising aqueous battery technologies on the path to commercial adoption. Though aqueous batteries are considered lower risk, they can still undergo problematic degradation processes. This perspective details the degradation that aqueous batteries can experience during normal and abusive operation, and how these processes can even lead to cascading failure. We outline methods for studying these phenomena at the material and single-cell level. Considering reliability and safety studies early in technology development will facilitate translation of emerging aqueous batteries from the lab to the field.

25 ENERGY STORAGE↗
DOE OSTI2017

The Relationship between Shunt Currents and Edge Corrosion in Flow Batteries

Shunt currents occur in electrochemical reactors like flow batteries, electrolyzers, and fuel cells where many bipolar cells that are connected in series electrically contact a mobile electrolyte through one or more common fluid distribution manifolds. Shunt currents reduce energy efficiency, and can cause unwanted side reactions including corrosion and gas generation. Equivalent-circuit models have been widely used to examine shunt currents in multi-cell electrochemical reactors. However, a detailed investigation of the interesting electrochemical processes occurring at the edges of the active areas has not been presented. In this work, the generation of shunt currents and their tendency to drive corrosion at the edges of positive electrodes in the most positive cells in a reactor stack are investigated with a comprehensive numerical model. An analytical model based on the penetration of current into a semi-infinite electrode, that can be used in conjunction with traditional equivalent-circuit models to assess the tendency for shunt currents to drive corrosion, is developed and compared to the numerical model. The models provided here can be used to set requirements on maximum allowable port currents in order to achieve a particular durability goal.

25 ENERGY STORAGE↗
DOE OSTI2015

Processing and Pretreatment Effects on Vanadium Transport in Nafion Membranes

Here, this work describes how manufacturing processes and pretreatments affect the proton conductivity and vanadyl permeability of Nafion® and how these properties are altered by running in a cell. Five Nafion membranes were examined: reinforced XL100, dispersion cast NR211 and NR212, and extruded N115 and N117. The membranes were subjected to pretreatments that included annealing at 120°C and immersing in ambient temperature and boiling water and sulfuric acid. Vanadyl permeability varied by ~15X with pretreatment and ~3X with manufacturing process. Variations in ionic conductivity were comparatively modest: ~1.5X with pretreatment and ~1.2X with processing. Differences in permeability can be eliminated by annealing the extruded membranes above their glass-transition temperature or by immersing in boiling sulfuric acid. The differences induced by processing and pretreatments were largely absent from membranes removed from vanadium redox cells subjected to repeated charge/discharge cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Redox Flow Batteries: An Engineering Perspective

Redox flow batteries are well suited to provide modular and scalable energy storage systems for a wide range of energy storage applications. In this paper, we review the development of redox flow battery technology including recent advances in new redox active materials and systems. We discuss cost, performance, and reliability metrics that are critical for deployment of large flow battery systems. The technology, while relatively young, has the potential for significant improvement through reduced materials costs, improved energy and power efficiency, and significant reduction in the overall system cost.

Batteries↗