Search NASA⌕ Search

Engineering topics

Peshek, Timothy J.

Publications and source records attributed to Peshek, Timothy J..

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Thermal Performance of Perovskite-Based Photovoltaics for Operation in Low Earth Orbit

Perovskite-based photovoltaics are attractive for applications in space. The space environment is harsh with ionizing radiation, atomic oxygen, UV radiation, extreme temperatures, and thermal cycling. Herein, the thermal performance of perovskite active layer and perovskite photovoltaic devices in low earth orbit is analyzed. A 1 μm silicon oxide layer coupled with 500 nm zirconia thin film aid in cell thermal management is determined. The residual stresses between various layers in a device are modeled and it is proved that thermally induced mechanical failure of the perovskite (time > 460 years) is unlikely during operating lifetime of any mission. In conclusion, target power conversion efficiencies are also shared to manage maximum operating temperature of a perovskite-based device.

14 SOLAR ENERGY↗
DOE OSTI2023

Combined Stress Testing of Perovskite Solar Cells for Stable Operation in Space

Perovskite solar cells (PSCs) could provide new low-cost opportunities for powering spacecraft. Here we are designing a PSC resilient to lunar surface conditions, focusing on contact/barrier layers combinations that maximize stability. Thermal vacuum stress shows cells with gold back-contacts and SiOx protection retain >90% of initial efficiency and indium tin oxide (ITO)-contacted cells retain ~100% of initial efficiency after five months of stress. SiO x mitigates mechanical aspects of contact stress, retaining 99% of initial efficiency, whereas cells with silicone/cover glass decreased 27%. We further exposed cells to combined illumination, 75 °C heat, and 10 -6 Torr vacuum for 24 h and found that ITO-contacted cells outperformed Au-contacted cells.

14 SOLAR ENERGY↗
DOE OSTI2023

Evaluation of Hybrid Perovskite Prototypes After 10-Month Space Flight on the International Space Station

Metal halide perovskites (MHPs) have emerged as a prominent new photovoltaic material combining a very competitive power conversion efficiency that rivals crystalline silicon with the added benefits of tunable properties for multijunction devices fabricated from solution which can yield high specific power. Perovskites have also demonstrated some of the lowest temperature coefficients and highest defect tolerance, which make them excellent candidates for aerospace applications. However, MHPs must demonstrate durability in space which presents different challenges than terrestrial operating environments. To decisively test the viability of perovskites being used in space, a perovskite thin film is positioned in low earth orbit for 10 months on the International Space Station, which was the first long-duration study of an MHP in space. Postflight high-resolution ultrafast spectroscopic characterization and comparison with control samples reveal that the flight sample exhibits superior photo-stability, no irreversible radiation damage, and a suppressed structural phase transition temperature by nearly 65 K, broadening the photovoltaic operational range. Further, significant photo-annealing of surface defects is shown following prolonged light-soaking postflight. Here these results emphasize that methylammonium lead iodide can be packaged adequately for space missions, affirming that space stressors can be managed as theorized.

14 SOLAR ENERGY↗
DOE OSTI2022

Countdown to perovskite space launch: Guidelines to performing relevant radiation-hardness experiments

Perovskite photovoltaics (PVs) are under intensive development for promise in terrestrial energy production. Soon, the community will find out how much of that promise may become reality. Perovskites also open new opportunities for lower cost space power. However, radiation tolerance of space environments requires appropriate analysis of relevant devices irradiated under representative radiation conditions. We present guidelines designed to rigorously test the radiation tolerance of perovskite PVs. We review radiation conditions in common orbits, calculate nonionizing and ionizing energy losses (NIEL and IEL) for perovskites, and prioritize proton radiation for effective nuclear interactions. Low-energy protons (0.05-0.15 MeV) create a representative uniform damage profile, whereas higher energy protons (commonly used in ground-based evaluation) require significantly higher fluence to accumulate the equivalent displacement damage dose due to lower scattering probability. Furthermore, high-energy protons may "heal" devices through increased electronic ionization. These procedural guidelines differ from those used to test conventional semiconductors.

14 SOLAR ENERGY↗
DOE OSTI2022

What Would It Take to Manufacture Perovskite Solar Cells in Space?

Imagine: Astronauts land on the moon. They verify their arrival with mission control and perform system checks and validations. After the dust settles, they open the airlock of the landing vehicle and venture outside. A side hatch opens, and a flexible substrate slowly unfurls on a boom. A series of printer heads raster, hovering over the substrate and sequentially vapor-depositing the constituent layers of a perovskite solar module. In time, a 1-megawatt array has been manufactured on the moon and can now be connected to supply power to the Artemis Base Camp. This ambitious vision could someday become a reality.

14 SOLAR ENERGY↗
NASA NTRS2019

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗
NASA NTRS2019

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗
NASA NTRS2018

Evidence for Arcing on the International Space Station Solar Arrays

The International Space Station (ISS) is powered by a set of 160 V photovoltaic arrays (PVA) in the US sector. Arcing thresholds for the ISS PVAs measured in the laboratory are shown to vary from -210 V to -457 V depending on the ambient plasma density, where low arcing threshold occurs at high plasma densities. Arcing of ISS PVAs on-orbit is unlikely under normal operating conditions. The net potential of a solar cell relative to space depends on the position of the cell within a string, the (vxB)•L contribution to the potential at the location of the cell, and the frame potential of ISS due to solar array charging. Net potentials on a cell will reach the arcing threshold only on rare occasions. However, the situation changes when damaged PVA strings are considered. Open circuit strings can exhibit voltages exceeding -300 V when the strings are shunted. Under these conditions the local potential on the damaged string can easily exceed arcing thresholds at the low end of the -210 V to -457 V range for ISS PVAs. Because arcing to space on the array will remove some fraction of the net negative charge on the ISS, transient variations in the frame potential are expected during the electrostatic discharge events. We report a new class of transient ISS frame potential variations consistent with arcing on open strings using data from the ISS Floating Potential Measurement Unit’s Floating Potential Probe instrument.

Minow, Joseph I.↗
NASA NTRS2018

Advanced Development of Space Photovoltaic Concentrators Using Robust Lenses, Multi-Junction Cells, and Graphene Radiators

At the past three PVSCs, our team has presented recent advances in our space photovoltaic concentrator technology. In the past year, under multiple NASA-funded research and technology development programs, our team has made much additional progress in the advanced development of space photovoltaic concentrators. New robust Fresnel lenses, new high-efficiency multi-junction cells, and new graphene radiators have been developed. The paper will present the latest advances in this technology.

O'Neill, Mark↗
NASA NTRS2018

Insights into Space Solar Cell Durability Using SPICE Simulation Seeded by Current-Voltage Characteristics Parametrized Using the Lambert W Special Function

We developed and validated an automated routine for the fitting of I-V curve data to the single diode model according to an exact analytical solution. Our fitting routine was validated to show good noise immunity and high accuracy usingsimulated values from LTSPICE. We are thus able to automate parameter extraction from a dataset or arbitrary size. This parameterization allows for better simulation of performance of real cells and arrays and provides utility for a host of applications relevant to space arrays. We will use this methodology to determine the array performance of radiated cells over time, and simulate the performance of the arrays with bypass diodes and power electronics.

Solar Cell↗