Engineering topics

Peters, Daniel J.

Publications and source records attributed to Peters, Daniel J..

5 records

NASA NTRS1960

Experimental Evaluation of Rocket Exhaust Diffusers for Altitude Simulation

An experimental investigation of exhaust diffusers has been conducted to evaluate various methods of minimizing the overall pressure ratio (from chamber to ambient pressure) required to establish and maintain full expansion of the nozzle flow (altitude simulation). Exhaust-diffuser configurations investigated were (1) cylindrical diffusers, (2) diffusers with contraction, and (3) diffusers including a right-angle turn. Cylindrical diffusers were evaluated with primary nozzles of various area ratios and types, as well as two clustered configurations; the other diffusers were evaluated with individual nozzles of constant area ratio and varied type. Air was the working fluid, except for two check points obtained with JP-4 fuel and liquid-oxygen rocket engines and cylindrical diffusers. The minimum length-diameter ratio of cylindrical diffusers was about 6 for minimum pressure-ratio requirements. With cylindrical diffusers of adequate length, the pressure-ratio requirements were primarily a function of the ratio of diffuser to nozzle-throat areas and were essentially independent of primary-nozzle type (including two clustered configurations) or area ratio. The two check points obtained with rocket engines indicated the pressure-ratio requirements at given ratios of diffuser to nozzle-throat areas were lowered, as compared with the requirements with air, as a result of the reduced ratio of specific heats. The minimum length-diameter ratio of the contraction throat of convergent-divergent diffusers was also about 6 for minimum pressure-ratio requirements. With adequate contraction-throat length, the pressure-ratio requirements of such diffusers were appreciably below those of comparable cylindrical diffusers when used with conical and cutoff-isentropic nozzles, but not when used with a bell nozzle. Minimum pressure-ratio requirements of a diffuser including a simple long-radius right-angle turn at maximum diffuser area, obtained with the center of radius of the turn a minimum of 2 diffuser diameters downstream of the nozzle exit, were not appreciably above those of a comparable optimum cylindrical diffuser. A diffuser including a long-radius right-angle turn at a contraction minimum area had somewhat lower pressure-ratio requirements than the aforementioned simple turn.

Sivo, Joseph N.↗

NASA NTRS1959

Comparison of Rocket Performance using Exhaust Diffuser and Conventional Techniques for Altitude Simulation

A rocket engine with an exhaust-nozzle area ratio of 25 was operated at a constant chamber pressure of 600 pounds per square inch absolute over a range of oxidant-fuel ratios at an altitude pressure corresponding to approximately 47,000 feet. At this condition, the nozzle flow is slightly underexpanded as it leaves the nozzle. The altitude simulation was obtained first through the use of an exhaust diffuser coupled with the rocket engine and secondly, in an altitude test chamber where separate exhauster equipment provided the altitude pressure. A comparison of performance data from these two tests has established that a diffuser used with a rocket engine operating at near-design nozzle pressure ratio can be a valid means of obtaining altitude performance data for rocket engines.

Sivo, Joseph N.↗

NASA NTRS1958

Altitude Performance of the Afterburner on the Iroquois Turbojet Engine. Coord. No. AF-P-6

The performance and operational characteristics of two afterburner configurations for the Iroquois turbojet engine were evaluated in an altitude test chamber over a range of afterburner equivalence ratios at afterburner-inlet pressures from 733 to 3186 pounds per square foot absolute. These conditions correspond to an altitude range from 38,700 to 66,800 feet at a flight Mach number of 1.5. The only difference between the two afterburner configurations was in the pattern of afterburner fuel injection. At an afterburner-inlet pressure of approximately 3100 pounds per square foot absolute, corresponding to an altitude of 38,700 feet and a_ flight Mach number of 1.5, the combustion efficiency of both configurations reached peak values of 0.80 to 0.85 at equivalence ratios of 0.35 to 0.40. However, further reduction in the afterburner-inlet pressure severely affected combustion efficiency. For example, at an afterburner inlet pressure level of 700 to 1000 pounds per square foot absolute, the efficiency for both configurations was 0.20 to 0.40.

Groesbeck, Donald E.↗

NASA NTRS1958

Some Altitude Operational Characteristics of a Prototype Iroquois Turbojet Engine. COORD. NO. AF-P-6

The evaluation of the altitude operational characteristics was part of the over-all investigation of the early developmental Iroquois engine. Engine steady-state windmilling characteristics were evaluated over a range of flight Mach numbers from 0.48 to 1.72 at altitudes of 35,000 and 50,000 feet. Engine altitude ignition limits were obtained over a range of flight Mach numbers from 0.5 to 1.5 with the standard engine ignition system and also with an oxygen boost system. A short investigation of high-speed altitude reignition following combustor blowout was conducted.

Peters, Daniel J.↗

NASA NTRS1951

Investigation of Surge Characteristics of XJ34-WE-32 Turbojet Engine

Surge characteristics of the XJ34-WE-32 turbojet engine were determined over a range of altitudes. Several typical oscillograph traces during which surge occurred are presented. The effect of altitude on the surge line and it's relation to the steady-state operating region are shown.

Groesbeck, Donald E.↗