Search NASA⌕ Search

Engineering topics

Petrie, T W

Publications and source records attributed to Petrie, T W.

At least 19 records

Balancing Current Drive and Heating in DIII-D High Noninductive Current Fraction Discharges Through Choice of the Toroidal Field

In order to maintain stationary values of the stored energy and the plasma current in a tokamak discharge with all of the current driven noninductively, the sum of the alpha-heating power and the power required to provide externally driven current must be equal to the power required to maintain the pressure against transport losses. In a study of high noninductive current fraction discharges in the DIII-D tokamak, it is shown that in the case of present-day tokamaks with no alpha-heating, adjustment of the toroidal field strength (B(T)) is a tool to obtain this balance between the required current drive and heating powers with other easily modifiable discharge parameters (beta(N), q(95), discharge shape, n(e)) fixed at values chosen to satisfy specific constraints. With all of the external power sources providing both heating and current drive, and beta(N) and q(95) fixed, the fraction of externally driven current scales with B(T) with little change in the bootstrap current fraction, thus allowing the noninductive current fraction to be adjusted.

Ferron, J R↗

Toroidally Resolved Structure of Divertor Heat Flux in RMP H-mode Discharges on DIII-D

As shown on DIII-D edge localized modes (ELMs) can be either completely eliminated or mitigated with resonant magnetic perturbation (RMP) fields. Two infrared cameras, separated 105 degrees toroidally, were used to make simultaneous measurements of ELM heat loads with high frame rates. Without the RMP fields ELMs display a variety of different heat load dynamics and a range of toroidal variability that is characteristic of their 3D structure. Comparing radial averages there is no asymmetry between two toroidal locations. With RMP-mitigated ELMs, the variability in the radially averaged power loads is significantly reduced and toroidal asymmetries in power loads are introduced. In addition to RMP ELM suppression scenarios an RMP scenario with only very small ELMs and very good confinement has been achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

UEDGE simulation of edge plasmas in DIII-D double null configurations

Analysis of plasma flow in the edge of double null hybrid mode DIII-D plasmas is reported. The two dimension fluid plasma code UEDGE [T. Rognlien et al., J. Nucl. Mater. 196-198, 347 (1992)] is used for the analysis. The effect of impurity radiation from intrinsic carbon sputtered from plasma facing surfaces is included as is the effect of plasma drifts. Two discharges in which the flux surfaces through the poloidal field nulls (X-points) are separated by 1 cm at the outer midplane are analyzed. The discharges differ only in the direction of the ion {nabla}B drift. It is shown that the flow of both primary ions and intrinsic impurities is dominated by the effect of plasma drifts. Variations in the recycling of deuterium ions, as seen in D{sub {alpha}} emission profiles, are qualitatively consistent with experiment and are driven by the effect of ExB drifts associated with radial gradients of the electron temperature at the secondary separatrix. Trace argon impurity is introduced to simulate the transport of argon used in the experiment to enhance divertor radiation power. Penetration of the trace argon to the closed field lines depends on the direction of the ion {nabla}B drift, consistent with experiment. The analysis described here includes the effect of a deuterium gas puff to establish the ''puff and pump'' configuration. The poloidal flow of impurities is a balance between the projection of the parallel flow and poloidal drifts, primarily from ExB. It is shown that the effect of the gas puff is primarily to alter the electron temperature profile and thus affects impurity flow via alteration of ExB drifts, not via entrainment in deuterium ion parallel flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of ITER operational scenarios on DIII-D

The DIII-D programme has recently initiated an effort to provide suitably scaled experimental evaluations of four primary ITER operational scenarios. New and unique features of this work are that the plasmas incorporate essential features of the ITER scenarios and anticipated operating characteristics; e. g. the plasma cross-section, aspect ratio and value of I/aB of the DIII-D discharges match the ITER design, with size reduced by a factor of 3.7. Key aspects of all four scenarios, such as target values for beta(N) and H(98), have been replicated successfully on DIII-D, providing an improved and unified physics basis for transport and stability modelling, as well as for performance extrapolation to ITER. In all four scenarios, normalized performance equals or closely approaches that required to realize the physics and technology goals of ITER, and projections of the DIII-D discharges are consistent with ITER achieving its goals of >= 400MW of fusion power production and Q >= 10. These studies also address many of the key physics issues related to the ITER design, including the L-H transition power threshold, the size of edge localized modes, pedestal parameter scaling, the impact of tearing modes on confinement and disruptivity, beta limits and the required capabilities of the plasma control system. An example of direct influence on the ITER design from this work is a modification of the physics requirements for the poloidal field coil set at 15 MA, based on observations that the inductance in the baseline scenario case evolves to a value that lies outside the original ITER specification.

CONFINEMENT↗

Plasma Shape Optimization for Steady-State Tokamak Development in DIII-D

For a more detailed account of the results summarized here and for references, see C.T. Holcomb et al., Phys. Plasmas 16, 056116 (2009). Advanced tokamak research on DIII-D is focused on developing a high fusion gain, steady-state scenario that would eliminate or greatly reduce the demands on an inductive transformer in future machines. Steady-state operation requires the inductively driven current density (j{sub Ind}) be zero everywhere. Most of the total current I{sub p} is typically from self-driven bootstrap current, with the remainder driven by external noninductive sources, such as neutral beam and radiofrequency current drive. This paper describes an extension of the fully noninductive condition (f{sub NI} {approx} 100%) to {approx}0.7 current relaxation times that was achieved by a combination of more available ECCD and new scientific insights. The insights are an optimization of performance through variation of the plasma shape parameter known as squareness ({zeta}) and an optimization of divertor magnetic balance. These optimizations simultaneously improve stability, confinement, and density control. These are each essential for achieving fully noninductive operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗