Engineering topics
Pettes, Michael T.
Publications and source records attributed to Pettes, Michael T..
Structural alignment of ZnO columns across multiple monolayer MoS 2 layers as compliant substrates
The study reveals that a two-dimensional (2D) material as substrate for heterogeneous integration acts as a compliant substrate.
Evidence of hexagonal germanium grains on annealed monolayer MoS 2
Growing three-dimensional (3D) materials on two-dimensional (2D) van der Waals surface has shown its effectiveness in overcoming materials incompatibility for stacking transferrable membranes toward advanced device manufacturing. Herein, we demonstrate that the nucleation of hexagonal germanium (Ge) grains within a continuous crystalline film, which has been unfeasible through traditional epitaxy techniques, is realized by chemical vapor deposition on top of n-type monolayer molybdenum disulfide (MoS 2 ) substrates. Suggested by quantum molecular dynamics calculation, the hexagonal Ge nucleation is thermodynamically preferable to cubic Ge when growing on monolayer MoS 2 with sulfur vacancies. The strained hexagonal Ge grains have been confirmed by transmission electron microscopy analyses from both real space and reciprocal space. Scanning probe microscopy shows that the hexagonal Ge film possesses higher reflectivity in infrared spectral range, implying a higher carrier concentration resulted from the narrower band gap, as compared to cubic Ge.
Analysis of Coronado State Historic Site artifacts using X‐rays
Abstract Two historic‐period metal artifacts were provided by the New Mexico Historic Sites to Los Alamos National Laboratory for non‐destructive analysis. The artifacts were a crossbow quarrel (or bolthead) and a reliquary pendant recovered from Kuaua Pueblo (also known as the Coronado Historic Site) in Bernalillo, NM. The quarrel is a heavily patinated metal that had been flattened due to compressive forces. The pendant consisted of a metal casing that had previously surrounded two center gemstones on the front and rear face of the pendant. The gemstone in the rear setting had fractured and was displaced from the setting, leaving only a small, loose fragment within the pendant for study. The front gem appeared to be very dark, near‐black in color, and the fragment of the rear gem was a bright red color. The artifacts were analyzed to ascertain their composition and glean insight into their provenance using the following X‐ray techniques: X‐ray computed tomography, confocal micro X‐ray fluorescence, and X‐ray diffraction. Infrared spectroscopy and electron microscopy were used on selected areas. Ultraviolet Raman spectra were collected on the two gems and the pendant. The metal material of the artifacts was found to be primarily composed of copper. The gems in the pendant were composed of manganese (front gem) and calcium (side gem).
Reliability Improvement and Effective Switching Layer Model of Thin-Film MoS 2 Memristors
2D memristors have demonstrated attractive resistive switching characteristics recently but also suffer from the reliability issue, which limits practical applications. Previous efforts on 2D memristors have primarily focused on exploring new material systems, while damage from the metallization step remains a practical concern for the reliability of 2D memristors. Here, the impact of metallization conditions and the thickness of MoS 2 films on the reliability and other device metrics of MoS 2 -based memristors is carefully studied. The statistical electrical measurements show that the reliability can be improved to 92% for yield and improved by ≈16× for average DC cycling endurance in the devices by reducing the top electrode (TE) deposition rate and increasing the thickness of MoS 2 films. Intriguing convergence of switching voltages and resistance ratio is revealed by the statistical analysis of experimental switching cycles. An “effective switching layer” model compatible with both monolayer and few-layer MoS 2 , is proposed to understand the reliability improvement related to the optimization of fabrication configuration and the convergence of switching metrics. In conclusion, the Monte Carlo simulations help illustrate the underlying physics of endurance failure associated with cluster formation and provide additional insight into endurance improvement with device fabrication optimization.
Subsurface Characteristics of Metal-Halide Perovskites Polished by an Argon Ion Beam
Focused ion beam (FIB) techniques have been frequently used to section metal-halide perovskites for microstructural investigations. However, the ion beams directly irradiating the sample surface may alter its properties far different from those of pristine, potentially leading to modified deterioration mechanisms under aging stressors. Here, we combine complementary approaches to measure the subsurface characteristics of polished perovskites and identify the chemical species responsible for the measured properties. Analysis of the experimental results in conjunction with Monte Carlo simulations indicates that atomic displacements and local heating occur in the first ≈15 nm of the subsurface of methylammonium lead iodide (MAPbI 3 ) by glancing-angle Ar + beam irradiation (4 kV at 3°). The lead-rich, iodine-deficient surface promotes rapid phase segregation under thermal aging conditions. On the other hand, despite the subsurface modification, our experiments confirm that the rest of the MAPbI 3 bulk retains the material integrity. Our observation supports that polished perovskites could serve in studying the properties of bulk or buried junctions far away from the altered subsurface with care.
Work function lowering of LaB 6 by monolayer hexagonal boron nitride coating for improved photo- and thermionic-cathodes
We report a lowering of work function for lanthanum hexaboride (LaB 6 ) by monolayer hexagonal boron nitride (hBN) coating. Photoemission electron microcopy (PEEM) and thermionic emission electron microscopy (TEEM) both revealed that the hBN coated region of a LaB 6 (100) single crystal has a lower work function compared to the bare (i.e., non-coated) and graphene coated regions. A broad and uniform brighter image of the hBN coated region in PEEM was quantitatively supported by a 0.4 eV decrease in the work function in photoelectron spectra compared to the bare region. TEEM results were consistent in that the hBN coated region exhibited thermionic emission at 905 °C, whereas the bare and graphene coated regions did not. A larger decrease in the work function for hBN coated LaB 6 (100) compared to graphene coated LaB 6 (100) was qualitatively supported by our density functional theory calculations. Adding an oxide layer in the calculations improved consistency between the calculation and experimental results. We followed up our calculations with synchrotron-radiation x-ray photoelectron spectroscopy and confirmed the presence of an oxide layer on our LaB 6 .
Surface Effects on Anisotropic Photoluminescence in One‐Dimensional Organic Metal Halide Hybrids
1D organic metal halide hybrids (OMHHs) exhibit strongly anisotropic optical properties, highly efficient light emission, and large Stokes shift, holding promise for novel photodetection and lighting applications. However, the fundamental mechanisms governing their unique optical properties and in particular the impacts of surface effects are not understood. Herein, 1D C 4 N 2 H 14 PbBr 4 by polarization‐dependent time‐averaged and time‐resolved photoluminescence (TRPL) spectroscopy, as a function of photoexcitation energy, is investigated. Surprisingly, it is found that the emission under photoexcitation polarized parallel to the 1D metal halide chains can be either stronger or weaker than that under perpendicular polarization, depending on the excitation energy. The excitation‐energy‐dependent anisotropic emission is attributed to fast surface recombination, supported by first‐principles calculations of optical absorption in this material. The fast surface recombination is directly confirmed by TRPL measurements, when the excitation is polarized parallel to the chains. The comprehensive studies provide a more complete picture for a deeper understanding of the optical anisotropy in 1D OMHHs.
Determination of P?V equation of state of a natural clinoptilolite using high-pressure powder synchr
Explore the source record for details and available documents.
Induced Ferromagnetism in Epitaxial Uranium Dioxide Thin Films
Abstract Actinide materials have various applications that range from nuclear energy to quantum computing. Most current efforts have focused on bulk actinide materials. Tuning functional properties by using strain engineering in epitaxial thin films is largely lacking. Using uranium dioxide (UO 2 ) as a model system, in this work, the authors explore strain engineering in actinide epitaxial thin films and investigate the origin of induced ferromagnetism in an antiferromagnet UO 2 . It is found that UO 2+ x thin films are hypostoichiometric ( x <0) with in‐plane tensile strain, while they are hyperstoichiometric ( x >0) with in‐plane compressive strain. Different from strain engineering in non‐actinide oxide thin films, the epitaxial strain in UO 2 is accommodated by point defects such as vacancies and interstitials due to the low formation energy. Both epitaxial strain and strain relaxation induced point defects such as oxygen/uranium vacancies and oxygen/uranium interstitials can distort magnetic structure and result in magnetic moments. This work reveals the correlation among strain, point defects and ferromagnetism in strain engineered UO 2+ x thin films and the results offer new opportunities to understand the influence of coupled order parameters on the emergent properties of many other actinide thin films.
Synergistic single process additive manufacturing of hydro-responsive Ag nanoparticle composites by digital visible light processing 3D printing
Single unit process fabrication of a responsive Ag nanoparticle (NP) chemical hydrogel composite is achieved through digital visible light processing (DLP) 3D printing of a self-assembled nanostructured (multilamellar) resin doped with Ag( i ).