Engineering topics

Pham, Hien N.

Publications and source records attributed to Pham, Hien N..

8 records

DOE OSTI2024

Gas-phase surface modification to control catalyst structure and yields in methane dehydroaromatization

Methane dehydroaromatization (MDA) is a promising approach for direct methane transformation to aromatics and hydrogen. The benchmark catalyst Mo/H-ZSM-5 struggles to find commercial adoption because of thermodynamically-limited yields and rapid coking on Brønsted acid and molybdenum carbide species, especially on zeolite external surfaces. Here, gas-phase atomic layer deposition (ALD) overcoats H-ZSM-5 external surfaces with SiO 2 or Al 2 O 3 . NH 3 -TPD, HRTEM, and textural properties show that these overcoats exclusively passivate zeolite external surfaces. Under MDA conditions, SiO 2 gives softer coke and increases cumulative benzene yields by 25%, while Al 2 O 3 strongly decreases yields. H 2 -TPR and UV-visible and Raman spectroscopy show how the overcoats redisperse the MoO x precatalysts, especially over multiple deactivation and isothermal oxidative regeneration cycles. Combined with 27 Al-MAS NMR, MoO x redistribution and dealumination are seen as the causes of long-term deactivation over multiple regeneration cycles, and this process continues to occur regardless of the overcoat. Altogether, the deposition of a small amount of silica on the outer surface of Mo/H-ZSM-5 reduces the formation of hard coke, which could be regenerated by milder methods such as hydrogen treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Designing ultrastable Pt/CeO 2 -Al 2 O 3 nanosheet catalysts for three-way catalysts applications

Designing Rh-free, especially Pt-only, three-way catalysts with improved low-temperature activity/stability is highly desirable. Herein, we demonstrate that ultrastable Pt/CeO 2 -Al 2 O 3 nanosheet catalysts can be obtained based on a Sabatier principle of metal-support interaction. Tuning the surface coverage of penta-site rich γ-Al 2 O 3 nanosheets (AlNS, weak adhesion to Pt) by CeO 2 “nano-islands” (strong adhesion to Pt) can lead to the synthesis of Pt/60 wt.%CeO 2 -AlNS that have lower light-off temperatures for CO, hydrocarbons, and NO compared to conventional Pt/CeO 2 and Pt/Al 2 O 3 catalysts by 100–200°C and a similar performance with the state-of-the-art Rh-based catalyst. Further, incorporating CeO 2 on the surface of AlNS can retard the sintering of CeO 2 during harsh redox hydrothermal aging, associate with the strong interaction between CeO 2 “nano-island” and penta-site rich γ-Al 2 O 3 nanosheets. Moreover, the improved activity/stability of Pt/CeO 2 -AlNS catalysts can be attributed to tuning of the Pt detachment and migration from and back to the CeO 2 “nano-islands”, respectively, that keeps Pt as nanoclusters on CeO 2 , the most active species for three-way catalyst applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

The Role of Lewis Acid Sites in γ-Al 2 O 3 Oligomerization

Olefin oligomerization by γ-Al 2 O 3 has recently been reported, and it was suggested that Lewis acid sites are catalytic. The goal of this study is to determine the number of active sites per gram of alumina to confirm that Lewis acid sites are indeed catalytic. Addition of an inorganic Sr oxide base resulted in a linear decrease in the propylene oligomerization conversion at loadings up to 0.3 wt %; while, there is a >95 % loss in conversion above 1 wt % Sr. Additionally, there was a linear decrease in the intensity of the Lewis acid peaks of absorbed pyridine in the IR spectra with an increase in Sr loading, which correlates with the loss in propylene conversion, suggesting that Lewis acid sites are catalytic. Characterization of the Sr structure by XAS and STEM indicates that single Sr 2+ ions are bound to the γ-Al 2 O 3 surface and poison one catalytic site per Sr ion. The maximum loading needed to poison all catalytic sites, assuming uniform surface coverage, was ~0.4 wt % Sr, giving an acid site density of ~0.2 sites per nm2 of γ-Al 2 O 3 , or approximately 3 % of the alumina surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Strategies for regeneration of Pt-alloy catalysts supported on silica for propane dehydrogenation

Catalyst stability, resistance to deactivation, and regeneration remain a challenge for high temperature reaction processes. For Pt alloys used in propane dehydrogenation (PDH), the primary pathways of catalyst deactivation include coke formation and metal nanoparticle sintering over time. Recent work shows that silica-supported catalysts provide excellent selectivity for this reaction, but the regenerability of silica-supported catalysts has not been established. In this work, we study a series of Pt alloys, including PtMn, PtZn, and PtSn, for the PDH reaction at 550 °C and 600 °C, and we subject the catalysts to regeneration over multiple cycles. While oxidation in air restores the reactivity completely with minimal catalyst sintering, it is surprising to find that these catalysts can also be regenerated in pure hydrogen. Here we explore the types of coke formed on these catalysts using in situ temperature programmed oxidation (TPO). Two types of coke are found: one on the metallic NP surface, and a second on the silica support. Our work shows that treatment in hydrogen causes redistribution of the coke between the metal and support, which can restore most catalytic activity lost during a reaction run. Finally, periodic introduction of H 2 during a reaction cycle may constitute an unexplored strategy for extending the lifetime of PDH catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Ni/CeO 2 Nanocatalysts with Optimized CeO 2 Support Morphologies for CH 4 Oxidation

Catalytic oxidation of CH 4 over nonprecious Ni/CeO 2 catalysts has attracted wide attention. Controlling the morphology of a CeO 2 support can enhance the CH 4 oxidation activity without changing the catalyst composition. Here, in this paper, a series of 2 wt % Ni/CeO 2 nanocatalysts with different CeO 2 support morphologies (nanoparticles (P), rods (R), cubes (C)) and synthetic procedures (precipitation, sol-gel (SG)) were evaluated for their CH 4 oxidation performance. The redox properties of CeO 2 supports and corresponding Ni loaded catalysts were characterized by H 2 -temperature-programmed reduction and oxygen storage capacity (OSC) measurements. The relationship among the CeO 2 morphologies, surface areas, redox properties, and CH4 oxidation activity for both CeO 2 supports and Ni/CeO 2 catalysts was established. The findings suggest that CeO 2 -R has a greater amount of surface oxygen vacancies as well as an improved OSC and CH4 oxidation activity compared to CeO 2 -P and CeO 2 -C supports. The same CH 4 oxidation activity pattern was observed for the Ni containing catalysts (Ni/CeO 2 -R > Ni/CeO 2 -P > Ni/CeO 2 -C). Increasing the CeO 2 surface area by using a sol-gel synthesis method (CeO 2 -SG) improved the amount of surface oxygen vacancies and CH 4 oxidation performance of CeO 2 -SG and Ni/CeO 2 -SG compared to CeO 2 -R and Ni/CeO 2 -R, respectively. Finally, all studied Ni/CeO 2 nanocatalysts showed improved hydrothermal stability compared to conventional Pd/Al 2 O 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Designing Ceria/Alumina for Efficient Trapping of Platinum Single Atoms

Cerium oxide (ceria) has been shown to be very effective at trapping platinum atoms, due to formation of stable surface complexes at step edges, where coordinatively unsaturated cerium cations are present. But ceria loses its effectiveness when heated to high temperatures, due to loss of surface area and growth in particle size associated with sintering of the oxide. Being a rare-earth, and with limited supplies worldwide, it is important to develop methods to improve the effectiveness of ceria as a catalyst support. Here we explore the performance for trapping Pt atoms when the ceria is supported on a high surface area alumina carrier. This helps create a more sustainable catalyst formulation, especially if we can retain the high dispersion of Pt seen on ceria supports. For this work, we studied the atom trapping efficacy of ceria/alumina samples with increasing ceria content (8 wt% - 50%) and contrasted the behavior with pure ceria. Electron microscopy reveals that when dispersed on alumina, ceria is present in the form of crystalline nanoparticles as well as isolated cerium ions. These two forms of ceria differ markedly in their ability to trap Pt atoms. Atomically dispersed cerium is present in the form of Ce 3+ cations on alumina, however this form of ceria is not effective for trapping Pt atoms. Our results show that the atom trapped Pt resides primarily on crystalline ceria nanoparticles. CO oxidation was used as a probe reaction to evaluate the performance of these Pt AT /ceria-alumina catalysts. As a result, we conclude that over the range of ceria loadings we investigated, 50% ceria/alumina represents the optimal catalyst support for achieving high surface area and atom trapping efficiency while helping reduce the total ceria content in this catalyst system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

MgO(111) Nanocatalyst for Biomass Conversion: A Study of Carbon Coating Effects on Catalyst Faceting and Performance

Solid base metal oxide catalysts such as MgO offer utility in a wide variety of syntheses from pharmaceuticals to fuels. The (111) facet of MgO shows enhanced, unique properties relative to the other facets. Carbon coatings have emerged as a promising modification to impart metal oxide catalyst stability. Here, we report the synthesis, characterization, and catalytic properties of commercial MgO, MgO(111), and carbon coated derivatives thereof for 2-pentanone condensation. The dimer and trimer products of this reaction can be used as precursors for biofuels upon oxygen removal and thus have relevance in environmental sustainability. Additionally, MgO(111) maintained impressive selectivity towards the dimer product after carbon coating, whereas the other catalysts experienced a decrease in conversion and selectivity as a consequence of the carbon coating. Our findings highlight the catalytic efficacy of MgO(111), provide insight into carbon coating for catalyst stability, and pave the way for continued mechanistic investigations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Creating Brønsted acidity at the SiO 2 -Nb 2 O 5 interface

Catalytically active acid sites associated with the silica-niobia interface were probed with a series of overcoated SiO 2 on Nb 2 O 5 (SiO 2 /Nb 2 O 5 ) mixed oxide materials prepared by deposition of tetraethyl orthosilicate onto niobic acid (Nb 2 O 5 nH 2 O) or calcined niobia (Nb 2 O 5 ). NH 3 TPD and pyridine DRIFTS studies indicated that the speciation of acid sites in the materials evolved as a function of SiO 2 loading, impacting the quantity and stability of Brønsted sites. Catalyst activity was highly dependent on SiO 2 loading in the liquid phase hydroalkoxylation of dihydropyran with n-octanol. At SiO 2 surface densities corresponding to approximately 1 Si per 2 surface Nb, the activity of these catalysts passed through a maximum approximately 20 times higher than the activity of calcined Nb 2 O 5 . We found that apparent reaction barriers measured over the most active SiO 2 /Nb 2 O 5 catalysts were 10 kJ/mol lower than those measured over niobic acid, suggesting that the OH features unique to the SiO 2 -Nb 2 O 5 interface were slightly more reactive than those on niobic acid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗