Search NASA⌕ Search

Engineering topics

Phillips, H

Publications and source records attributed to Phillips, H.

Plasma Processing of Large Surfaces with Application to SRF Cavity Modification

Plasma based surface modifications of SRF cavities present promising alternatives to the wet etching technology currently applied. To understand and characterize the plasma properties and chemical kinetics of plasma etching processes inside a single cell cavity, we have built a specially-designed cylindrical cavity with 8 observation ports. These ports can be used for holding niobium samples and diagnostic purposes simultaneously. Two frequencies (13.56 MHz and 2.45 GHz) of power source are used for different pressure, power and gas compositions. The plasma parameters were evaluated by a Langmuir probe and by an optical emission spectroscopy technique based on the relative intensity of two Ar 5p-4s lines at 419.8 and 420.07 nm. Argon 5p-4s transition is chosen to determine electron temperature in order to optimize parameters for plasma processing. Chemical kinetics of the process was observed using real-time mass spectroscopy. The effect of these parameters on niobium surface would be measured, presented at this conference, and used as guidelines for optimal design of SRF etching process.

Upadhyay, Janardan↗

NbTiN Based SIS Multilayer Structures for SRF Applications

For the past three decades, bulk niobium has been the material of choice for SRF cavities applications. RF cavity performance is now approaching the theoretical limit for bulk niobium. For further improvement of RF cavity performance for future accelerator projects, Superconductor Insulator - Superconductor (SIS) multilayer structures (as recently proposed by Alex Gurevich) present the theoretical prospect to reach RF performance beyond bulk Nb, using thinly layered higher-Tc superconductors with enhanced Hc1. Jefferson Lab (JLab) is pursuing this approach with the development of NbTiN and AlN based multilayer SIS structures. This paper presents the results on the characteristics of NbTiN films and the first RF measurements on NbTiN-based multilayer structure on thick Nb films.

Valente, Anne-marie↗

R&D Energy Recovery Linac at Brookhaven National Laboratory

Collider Accelerator Department at BNL is in the final stages of developing the 20-MeV R&D energy recovery linac with super-conducting 2.5 MeV RF gun and single-mode super-conducting 5-cell RF linac. This unique facility aims to address many outstanding questions relevant for high current (up to 0.5 A of average current), high brightness energy-recovery linacs with novel Zigzag-type merger. We present the performance of the R&D ERL elements and detailed commissioning plan.

43 PARTICLE ACCELERATORS↗

PLASMA ETCHING RATES AND SURFACE COMPOSITION OF BULK NIOBIUM TREATED IN Ar/Cl2 MICROWAVE DISCHARGE

To achieve theoretically predicted values of the accelerating fields in superconducting radiofrequency (SRF) cavities, their inside surface should be fairly smooth and free of impurities. Thus, surface preparation is the critical step in production of SRF cavities. Plasma etching process is a dry chemistry technique that can be used to achieve these requirements. It is based on interaction between reactive halogen species produced in the glow discharge and the surface. During this process, volatile Nb halides are evaporated from the surface of Nb, removing the mechanically damaged and contaminated layer. We present a treatment of bulk Nb samples in the Ar/Cl2 microwave discharge. We have shown that etching rates of bulk Nb as high as 1.5 mm/min can be achieved without introducing impurities in Nb. The rate dependence on various discharge parameters and reactive gas composition is presented. Surface composition and topology measurements were carried out before and after plasma treatment

43 PARTICLE ACCELERATORS↗

High etching rates of bulk Nb in Ar/Cl2 microwave discharge

Niobium is the material of choice for production of superconducting radio frequency cavities used in linear particle accelerators. In this study, plasma etching of bulk Nb is performed on the surface of disk shaped samples with the goal of eliminating non-superconductive pollutants in the penetration depth region and mechanically damaged surface layer. We have demonstrated that, in the microwave glow discharge, the etchings rates of 1.5 ?m/min can be achieved using Cl2 as reactive gas. The influence of plasma parameters such as input power, pressure, and concentration of the reactive gas on the etching rates is determined.

43 PARTICLE ACCELERATORS↗